clock SMART FORTWO COUPE 2008 User Guide

Instrument cluster
>> Controls.
141
The buttons for setting the time are on the top
of the cockpit clock.1
Setting the time forward
2
Setting the time back> Setting the time forward in 1 minute
increments
: Press button
1 repeatedly
until the desired time is set.
> Setting the time forward quickly: Press
button
1 for longer than two seconds.
The setting speed accelerates.
> Setting the time back in 1 minute
increments: Press button
2 repeatedly
until the desired time is set.
> Setting the time back quickly: Press
button
2 for longer than two seconds.
The setting speed accelerates.
!
Do not hang any objects on the cockpit
clock.
This could cause the cockpit clock to be torn
from its mounting and damage it.
Adjusting instrument cluster
illuminationYou can adjust the illumination of the
switches, the dials in the instrument cluster,
the radio*, the climate control* panel and the
auxiliary instruments*.
Five settings are possible.
>Make sure that the key in the starter switch
is turned to position1.
>Switch on the parking lamps.
> To brighten or dim illumination: Press right
button
2 (
page 138) repeatedly until the
desired setting is reached.
The current setting is stored. P68.10
3615
31

Loading and storing
>> Controls.
161
> Opening: Pull on glove box lid release
2
and fold down the glove box lid.
>Closing: Lift up the glove box lid with a bit
of force until it engages.
>Locking: Insert the key into glove box
lock
1 and turn counterclockwise.
> Unlocking: Insert the key into glove box
lock1 and turn clockwise.Storage compartment in the tailgate
1
You can store small objects in the storage
compartment in the tailgate.1
Handle
>Open the tailgates.
>Pull handle
1 on the inside of the tailgate
backward.
>Lift up the storage compartment cover.
Loading instructions
1 coupé only.
G
Warning!
Transport heavy or hard objects in the
cargo compartment, not in the passenger
compartment.
Always fasten items being carried as
securely as possible using fastening ma

terials appropriate for the weight and
size of the load.
In an accident, during hard braking or
sudden maneuvers, loose items may be
thrown around inside the vehicle, causing
injury to vehicle occupants.

At the gas station
170
>> Operation >Turn off the engine.
>Remove the key from the starter switch.
>Open the fuel filler flap by pulling at the
point indicated by arrow
1.
>Turn the fuel filler cap counterclockwise
and hold on to it until possible pressure is
released.
>Take off the fuel filler cap.
!
The fuel filler cap is tethered to the fuel
filler flap. Do not drop the fuel filler cap. It
could damage the vehicle paint finish.
>To prevent gasoline vapors from escaping
into open air, fully insert filler nozzle unit.
>Only fill your tank until the filler nozzle unit
cuts out
do not top off or overfill.>Replace the fuel filler cap.
>Turn the fuel filler cap clockwise until the
handle grip overturns.
i
Make sure to close the fuel filler flap be

fore locking the vehicle as the fuel filler flap
locking pin prevents closing after you have
locked the vehicle.
>Close the fuel filler flap.
You should hear the latch close shut.
i
Only use premium unleaded gasoline with a
minimum Posted Octane Rating of 91 (average
of 96 RON/86 MON). Information on gasoline
quality can normally be found on the fuel
pump. Please contact gas station personnel in
case labels on the pump cannot be found.
For more information on gasoline, see
"Premium unleaded gasoline" (

page 306),
see "Fuel requirements" (

page 306), and
the, or contact an authorized smart center.
G
Warning!
Overfilling of the fuel tank may create
pressure in the system which could cause
a gas discharge. This could cause the gas
to spray back out when removing the fuel
pump nozzle, which could cause personal
injury.

Front compartment
>> Operation
179
>Allow the radiator to cool down for at least
30 minutes.
>Using a rag, turn pressure cap
1 slowly
approximately one half turn counterclock

wise to release any excess pressure.
>Continue turning pressure cap1
counter

clockwise
and remove it.
The coolant level is correct if the level
• for cold coolant: reaches marking bar
2
visible through the filling opening
• for warm coolant: is approximately 0.6 in
(1.5 cm) higher
>If necessary, add coolant.
Adding coolant
>Add coolant as required. The coolant level
may not exceed the maximum filling level.
>Replace and tighten pressure cap
1.
Windshield/rear window
1 washer
system
Both the windshield and the rear window
1
washer are supplied from the windshield
washer reservoir.
The recommended minimum filling level is
1.06 US qt (1.0 l).
The windshield washer reservoir is located in
the front compartment on the driver’s side.
1
CapDuring all seasons,
• use a windshield washer concentrate la

beled for summer and water for tempera

tures above freezing point.
• use a windshield washer concentrate la

beled for winter and water for tempera

tures below freezing point.
1 coupé only.
P82.35
2488
31
G
Warning!
Windshield washer concentrate is highly
flammable. Fire, naked flames and
smoking are prohibited when windshield
washer concentrate is being handled.

Vehicle care
228
>> Operation Removing insects
Remove insect remains before you start to
wash the vehicle.
>Spray insect remover on.
>Allow insect remover to work in briefly.
>Rub in gently with a soft cloth or sponge.
>Rinse with plenty of water.
>Treat the cleaned surface with hard wax.
Removing tar
Remove any tar marks before washing the
vehicle.
>Apply tar remover with a soft cloth.
>Allow tar remover to work in briefly.
>Rub in gently.
>Rinse with plenty of water.
>Treat the cleaned surface with hard wax.Vehicle washing
In the winter, thoroughly remove all traces of
road salt as soon as possible.
When washing the vehicle underbody, do not
forget to clean the inner sides of the wheels.
Washing your vehicle by hand
>Wash the vehicle using car shampoo
concentrate and a sponge.
>Rinse with clean water.
>Towel dry the vehicle.
!
Do not wash the vehicle in direct sunlight.
The body panel surfaces and paint finish may
be damaged.
Washing your vehicle in an automatic car wash
i
When running your vehicle through an
automatic car wash, water droplets can run
down the inside of the side windows.Unscrew your vehicle’s antenna before
driving into an automatic car wash.
1
Antenna
>Removing: Unscrew antenna
1 counter

clockwise.
>Fitting: Screw antenna
1 in clockwise. P82.62
3091
31

Where will I find ...?
234
>> Practical hints.
Tire repair kitThe tire repair kit is located in the passen

ger’s footwell under the carpet.1
Carpet holder
>Insert a suitable object such as a coin into
the slot of carpet holder
1.
>Turn carpet holder
1 counterclockwise.
>Lift the carpet.
2
Tire repair kit
The following is included:
• Tire sealant container
• Electric air pump with filler hose
•Sticker
• Operating instructions label (on the inside
of the tire repair kit lid)
i
The tire sealant container is located below
tire repair kit
2.
G
Warning!
The tire repair kit is a limited repair de

vice. In case of a breakdown caused by a
flat tire, read through the section flat
tire (

page 265) carefully. When using
the tire repair kit follow the instructions
in this section. Failure to follow these in

structions can result in severe injury or
death.

Replacing bulbs
>> Practical hints.
257
Low beam headlamp bulb
>Removing: Take off low beam headlamp
cover
3.
>Detach the electrical connector.
>Bend the retainer spring end down and
forward until it unclips. Fold the retainer
spring back.
>Pull the bulb out of the headlamp housing.
>Installing: Insert the new bulb into the
headlamp housing.
>Fold the retainer spring forward.
Bend the retainer spring end forward then
up and back to clip in.
>Attach the electrical connector.
>Reinstall low beam headlamp cover
3.High beam headlamp bulb
>Removing: Take off high beam headlamp
cover
4.
>Detach the electrical connector.
>Tilt the bulb socket down and pull it out.
>Pull the bulb out of the bulb socket.
>Installing: Insert the new bulb into the bulb
socket.
>Fit the bulb so that the retaining lug of the
base plate is pointing up.
>Press the bulb into the bulb socket until it
is fully engaged.
>Attach the electrical connector.
>Reinstall high beam headlamp cover
4.Front turn signal lamp bulb
>Removing: Turn bulb socket
2 counter

clockwise by a quarter of turn and pull it out
of the headlamp housing.
>Press gently onto the bulb and turn it
counterclockwise.
>Pull the bulb out of bulb socket2.
>Installing: Insert the new bulb into bulb
socket
2.
>Press gently onto the bulb and turn it
clockwise.
>Insert bulb socket
2 into the headlamp
housing.
The arrow on bulb socket
2 mu st be in l in e
with the line on the headlamp housing.
>Turn bulb socket
2 clockwise by a quarter
of turn.

Replacing bulbs
258
>> Practical hints. Side turn signal lamp bulb
>Removing: Open the door on the corre

sponding side.
1
Retaining lug
>Press on retaining lug
1 in the direction of
the arrow until the side turn signal lamp
housing disengages.
>Use a suitable tool to loosen the side turn
signal lamp housing from the fender.
>Turn the bulb socket counterclockwise and
pull it out out of the side turn signal lamp
housing.
>Pull the bulb out of the bulb socket.>Installing: Insert the new bulb into the bulb
socket.
>Insert the bulb socket into the side turn
signal lamp housing and turn the bulb
socket clockwise.
>Fit the side turn signal lamp housing onto
the fender.
>Press gently onto the side turn signal lamp
housing.
The side turn signal lamp housing must
audibly engage.
Replacing bulbs for rear lampsBefore you start to replace a bulb for a rear
lamp, do the following first:
>Turn exterior lamp switch to positionM
(

page 101).
>Switch off the ignition.
Tail lamp unit
>Removing:
Coupé:
>Open the upper tailgate.
>Open the lower tailgate.
Cabrio:
>Open the lower tailgate
>Open the rear soft top (

page 89)
>Remove the side cover in the cargo
compartment on the corresponding side.
>Fold the damping material forward, if
necessary.
P82.10
4556
31

Replacing bulbs
>> Practical hints.
259
Left bulb carrier illustrated as example1
Retaining tab
2
Electrical connector
>Press retaining tab
1 in the center of the
bulb carrier upwards.
>Pull the bulb carrier out of the tail lamp
housing.Left bulb carrier with bulb sockets (right bulb
carrier in reverse)
1
Retaining tab
3
Brake, tail, turn signal, and sidemarker
lamp bulb
4
Back
up lamp bulb
>Depending on which bulb needs to be
replaced, press gently onto bulb
3
or
4
and turn it counterclockwise.
>Pull the bulb out of the bulb socket.>Installing: Insert the new bulb into the bulb
socket.
>Press gently onto the bulb and turn it
clockwise until it engages.
>Insert the bulb carrier into the tail lamp
housing.
>Press gently onto the bulb carrier.
Let retaining tab
1 engage.
>Fold the damping material backward, if
necessary.
>Reinstall the side cover in the cargo com

partment.
P82.10
4527
31

Replacing bulbs
260
>> Practical hints. High mounted brake lamp
1
Retaining screws
2
High mounted brake lamp
3
Bulb socket
>Removing: Unscrew retaining screws
1.
>Remove high mounted brake lamp
2.
>Detach the electrical connector from bulb
socket
3.
>Turn the bulb counterclockwise and pull it
out of its socket.
>Installing: Install in the reverse order.License plate lamps
1
License plate lamp unit jacking point>Use a suitable tool to loosen the corre

sponding license plate lamp unit at jacking
point
1.
>Carefully unclip the license plate lamp unit.
2
Electrical connectors
3
Bulb
>Detach electrical connectors
2.
>Remove bulb
3.
>Insert the new bulb.
>Attach electrical connectors
2.
>Fit the license plate lamp unit on the right
and press gently on the left.
The license plate lamp unit must audibly
engage. P82.10
4838
31
G
Warning!
High outside temperature, stop
and
go
traffic, driving on long uphill grades, or
driving at high engine speed may increa

se the temperature in the engine com

partment. Therefore the area around the
air slots in the rear apron may be hot. Let
the engine cool off before touching this
area to prevent burns.
P82.10
4999
31