wiper SSANGYONG KORANDO 2012 Owner's Manual

08-37810-00
1. WIPER CONTROL
2. CAUTIONS ON RAIN SENSOR
When the wiper switch is in the AUTO position, the wiper will operate for 1 cycle if the initial engine
start is made. This may cause the wiper blades to wear prematurely. Therefore, other than rainy
days, set the switch to the OFF position. Especially during the winter time, check if the wiper blades
are not frozen to the windshield.
Operating the wiper with the blades frozen can damage the wiper motor.
If you operate the wipers when the windshield is dry without spraying washer fluid, the windshield
can be scratched and the wiper blades can wear prematurely. Use the wiper with the washer fluid
when the windshield is dry.
When it does not rain, turn the wiper switch to the OFF position.
Turn the wiper switch to the OFF position before any car wash to avoid unwanted operation of the
wipers. -
-
-
-Wiper mist & washer coupled wiper
Auto washer coupled wiper
Rain sensor coupled wiper operation (LIN)
Speed sensitive intermittent wiper
Wiper low/high control ▶
▶
▶
▶
▶
Check if the sensor is off the position.
Check if the rain sensor cover is securely installed.
Check if the customer is familiar to how to control the wiper sensitivity.
Check if the wiper sensitivity control is set to the FAST side (step 5).
Check the wiper blade for wear.
If the wiper blade cannot wipe the glass uniformly and clearly, it may cause the rain sensor to
work irregularly. Therefore, in this case, replace the wiper blade with a new one. -
-
-
-
- Irregular operation (abrupt operation) ▶ When cleaning the windshield over the sensor with damp clothes, the wiper may operate suddenly. It
could cause serious injury. Make sure to place the wiper switch to the OFF position and ignition switch
OFF when not in use.

08-4
3. MAJOR CHANGES
Windshield wiper blade
Wiper blade design and wiper arm pressure
Previous Current
Wiper arm pressure
Driver side = 900 ± 50 g
Passenger side = 600 ± 50 gWiper arm pressure
Driver side = 950 ± 50 g
Passenger side = 650 ± 50 g
Wiper blade design changed (blade size is the same)
Driver side: 600 mm (24 in)
Passenger side: 400 mm (16 in)

08-57810-00
1. WIPER AND WASHER SYSTEM
1) AUTO Washer Coupled Wiper Function
If you press the AUTO washer switch briefly with the ignition key ON and INT-AUTO switch "OFF", the
washer motor is operated for about 2 seconds to spray washer fluid once after the switch is turned ON
and the wiper relay is turned ON for 4 cycles. After that, the washer motor is operated for about 2
seconds to spray the washer fluid again and the relay is turned ON for 3 cycles and then the relay is
turned OFF.
2) Rear Washer Fluid Supply System
The front washer fluid reservoir supplies the rear washer fluid without additional washer fluid reservoir. Operating part for rear
wiper/washer
AUTO washer
switch (press)
Washer motor

08-77810-00
2. RAIN SENSING SYSTEM
In the rain sensing wiper operation system, the rain sensing unit only sends the information about the
amount of rain drops to the BCM, and it does not operate the wiper directly. The wiper and washer are
controlled by the BCM according to the driver's choice.
Rain sensing unitMultifunction wiper switch
AUTO and sensitivity control
This sensor emits infrared rays through LED
and then detects the amount of rain drops
by receiving the rays reflected off the
sensing section (rain sensor mounting
section on the windshield) with photodiode.AUTO: Wiper operates automatically by rain
sensor
FAST <-------> SLOW:
Auto delay/auto speed control.
A position that can control the sensitivity for
the amount of rains on the windshield and
transmit the wiping request signal
accordingly.
Rain sensor emitter lens
Auto light sensor sensing
portion

08-8
BCM ▶
The rain sensor detects the amount of rain drops and sends the operating request signal to the BCM,
which drives the wiper directly. At this moment, the BCM also sends the information on whether the
wiper is in operation mode or whether the multifunction wiper switch is in AUTO position to the rain
sensor.
BCM Underhood Fuse Box

08-10
Rain sensor unit
3. SYSTEM LAYOUT (INCLUDING RAIN SENSOR)
Wiper
Front wiper
Rear wiper
Rear washer hose and nozzle
For vehicles with
rear spoilerFor vehicles without rear
spoiler
WIPER AND WASHER SWITCH

08-12
4. WIPER AND WASHER OPERATION
1) Windshield Wiper Control Function
The wiper operates for 1 cycle when pushing
up the lever. The lever will return to the "OFF"
position when released.
Wiping speed control switch
When turning to FAST, wiping speed gets faster and when
turning to SLOW, wiping speed gets slower. Stop the operation.
Wiper speed controls automatically
according to the vehicle speed o
r
amount of rain (rain sensing wiper).
Wiping speed gets faster
when placing the pointer at
the "HI" position. Wiping speed gets slower when placing
the pointer at the "LO" position.
MIST
OFF
AUTO
LO
HI

08-137810-00
(1) Wiper mist
When the multifunction switch is pushed to the MIST position for 0.1 sec. or more with the IGN1 ON,
the wiper relay is turned on after 0.1 sec. has passed. When the wiper returns to the park position, the
wiper relay is turned off.
When the MIST switch signal is input the wiper is operated at high speed. When the switch is release
from the MIST position, the wiper is operated at low speed. 1.
2.

08-14
(2) Wiper LO/HI control
The wiper LOW relay is turned on when the multifunction wiper switch is at the LO position. The wiper
HIGH relay is turned on when the wiper switch is at the HI position. When the wiper switch is at the HI
position, both the LOW relay (constant operation) and HIGH relay are operated.
The wiper motor returns to parking position and stops, even when turning off the ignition switch during
wiper operation.
The wiper relay should stay ON in low/high wiper operation mode even if the parking signal for the
wiper motor is not received. In INT/AUTO wiper operation mode, the wiper relay should be turned
OFF after 5 seconds if there is no parking signal for the wiper for 3 seconds and informs the driver of
parking position signal abnormality.
While the wiper operates at low/high speed, the front/rear washer switch can be operated but the auto
washer switch cannot.
The wiper motor returns to parking position and stops when turning off the ignition switch during wiper
operation in high mode. 1.
2.
3.
4.
5.

08-157810-00
When holding the front washer switch at ON position for more than 0.6 seconds with IGN ON, the
wiper relay is activated 0.5 seconds after. The wiper stops after three more wipes since that the
washer switch is turned to "OFF" position. 1.
2) Windshield Washer Control Function
(1) Windshield washer coupled wiper
Wiper and Washer Coupled Operation
Pull the switch briefly (for less than 0.6 sec.)
: One wiping cycle
Pull and hold the switch for more than 0.6 sec.
: Three wiping cycles with washer fluid spray
<0b1d0b1d0b1d0b1d0b1d0b1d0b1d0b1d00470047004700470047004700470047004700470047004700470047004700470047004700470047004700470047004700470047004700470047004700470047004700470047004700470047004700470047004700
47004700470047004700470047004700470047>