key SSANGYONG KORANDO 2013 Manual Online

Smart key deactivation
This function prevents the operation by the smart key inside the vehicle even if the driver breaks in the
vehicle in the theft deterrent mode.
Deactivation conditions
- All doors closed (B-CAN)
- Theft deterrent mode activated (B-CAN)
- Smart key searchFOB deactivation: The smart key inside the
vehicle is deactivated when the passive
LOCK/REKES LOCK signal is input by a smart
key from the outside.
Smart key deactivation -
The REKES LOCK/passive LOCK (theft deterrent mode activation) request signal is sent by a
smart key outside the vehicle.
The smart key activated door LOCK is not found in the vehicle.
The system memorizes all smart keys found inside the vehicle as deactivated ones. 1.
2.
3.
Smart key deactivation actuation area -
Passive entry not available
Passive starting & power control not available
REKES function not available 1.
2.
3.
Cancellation of smart key deactivation -
When the theft deterrent mode is deactivated using a smart key outside the vehicle, the
deactivated smart key functions returns to be available. 1.In theft deterrent mode, the smart key(s) inside the vehicle is deactivated to prevent theft.

8712-03
7. SMART KEY VERIFICATION TIME CONTROL
The smart key verification time control consists of pre-verification timer and immobilizer verification timer,
and no verification process is required for 30 seconds after the each verification process has been
completed.
Pre-verification timer: Time for performing start & power mode function that controls the vehicle
power.
Immobilizer verification timer: Time for which the start with a smart key is possible after the SKM and
EMS (ECU) verify the immobilizer. -
-
Item Pre-verification timer Immobilizer verification timer
Operating power
Power OFF, ACC, IGN ON IGN ON after pre-verification (ACC)
FunctionTime for which the power control can be
carried out under the verified conditions
(30 seconds after the verification)Time for which the start request can be
carried out without a smart key under the
verified conditions
(30 seconds after the verification)
Input conditions
Verification
conditionsSmart key searching completed after the
following conditions are met:
Close signal input after any door
opened
Brake switch signal input
START/STOP switch signal input
After emergency slot inserted
After IGN OFF 1.
2.
3.
4.
5.Power changed to IGN ON after
valid pre-verification
Power changed to IGN ON by
smart key verification after pre-
verification timer completed
Smart key verification succeeded
by brake switch input after
immobilizer verification timer
completed with IGN ON
Smart key verification succeeded
after immobilizer verification timer
completed with IGN ON,
immobilizer verification and brake
switch input 1.
2.
3.
4. All doors closed
(including tailgate)
START/STOP switch input
Brake switch signal input
Smart key inserted into emergency
slot
Smart key searching completed
Engine start ON to OFF 1.
2.
3.
4.
5.
6.Brake switch signal input
START/STOP switch input 1.
2.

Component Pre-verification timer Immobilizer verification timer
Deactivation
conditions
If any condition for pre-verification timer and immobilizer verification timer is met, no verification process
is required for 30 seconds after the each verification process has been completed.
Operation before pre-verification timer
Passive LOCK/UNLOCK
REKES LOCK/UNLOCK -
-
Ignition status after immobilizer verification
The immobilizer verification has been completed when the engine starts.
The immobilizer verification is not deactivated until the ignition is turned to ON, OFF or ACC
ON.
The immobilizer is not deactivated when the key out warning condition is met while the engine
is running. -
-
-
8. START & POWER MODE CONTROL
The ignition status is changed to OFF, ACC ON, IGN ON and engine cranking by one START/STOP
switch.30 seconds has been passed after
the immobilizer verification timer
IGN1 OFF
No smart key is found inside the
vehicle with all doors closed after any
door has been opened and then
closed. 1.
2.
3. 30 seconds has been passed after
the pre-verification timer
Door handle switch ON
IGN ON
Theft deterrent mode
activation/deactivation
Door status changed (open/closed) 1.
2.
3.
4.
5.

Engine starting
When the START/STOP button is pressed with the brake pedal applied and gear selector lever in P or
N position, the SKM performs the immobilizer verification and sends the engine START request signal
to the EMS if a normal coded smart key is found.
When the .engine start request signal from the START/STOP switch is received, the SKM sends the
start request signal through the P-CAN and the vehicle power status signal to the BCM through the B-
CAN.
The SKM cuts the power for IGN2 and ACC relays while the engine is cranking as cutting the electric
load is necessary.
The SKM receives the engine start status signal from the EMS (ECU) through the P-CAN. 1.
2.
3.
4.
EMS (ECU)Engine rpm, engine cranking/stop/running/loaded
TCUGear selector lever position: P, N
ABS/ESPVehicle speed signal (wheel speed sensor on each wheel)
The SKM turns on the ACC/IGN2 relays after the engine cranking and sends the signal for IGN after
starting to the BCM through the B-CAN.
When the START/STOP button is pressed and engine cranking request1 signal is sent, the EMS
(ECU) cranks the engine after checking the engine warming up. If the engine cranking request2
signal is sent, the EMS cranks the engine without checking the engine warming up. 5.
6.
Engine cranking request1
(engine start after
warming up)When the START/STOP button is pressed briefly under the start
conditions, the vehicle starts to warming up and then the engine is started
after a certain amount of time (warming up indicator ON to OFF).
Engine cranking request2
(engine start without
warming up)When the START/STOP switch is pressed once again while the engine
cranking request1 signal is sent, the engine is started (regardless of
warming up indicator)
It can be delayed by several seconds according to the engine
coolant temperature.
Starting engine while driving 7.
The engine start request signal is sent when the START/STOP switch is pressed, provided that the
vehicle speed is less than 10 Km/h or no vehicle speed signal is input, the gear selector lever is in
N position and the brake switch is ON with IGN ON (30 sec. verification is not required).
The engine start request signal is sent regardless of the brake signal when the START/STOP
switch is pressed, provided that the vehicle speed is 10 Km/h or more and the gear selector lever is
in N position with IGN ON (30 sec. verification is not required). -
-

9. ESCL CONTROL
ESCL lock/unlock is not performed at ESCL virgin mode.
The SKM does not carry out the ESCL LOCK control if the engine is running with IGN ON or the
vehicle speed is 3 km/h or higher.
All the ESCL functions including START/STOP switch is disabled during anti-scanning flag bit set. -
-
-
If the smart key is pressed with power off, the electric steering motor performs the steering column
unlock. In some cases, power transition is carried out to ACC or IGN ON.
If the power transition and start is not possible after retry to LOCK or UNLOCK operation, the power
transition and start is not still possible after automatic retry and the warning lamp comes on. -
-
1) ESCL LOCK Control
When the ESCL is unlocked and the followings are met at normal condition:
If the driver door is open or closed with ignition key OFF, the electric steering motor performs the
steering column lock.
If the theft deterrent mode is activated by the LOCK signal from the passive or REKES key when
The ESCL LOCK is performed after 60 seconds since the ignition key is turned to B+ from
-
-
-
2) ESCL UNLOCL Control
When the ESCL is locked and the followings are met at normal condition:

8712-03
11. SKM WARNING CONTROL
(1) Smart Key Not Detected Warning
With ACC ON
Smart key not detected warning deactivation conditions
- ACC OFF, IGN1 ON, Smart key detected
IGN ON and engine running
Smart key not detected warning deactivation conditions
- IGN1 OFF, Smart key detected, Door openAny door except the driver door is opened and then closed.
The SKM starts to identify a smart key by using the interior antenna after confirming that all the doors
are closed through CAN communication with the BCM.
When no smart key is found, the SKM sends the smart key not detected warning signal to the BCM
and instrument cluster through B-CAN.
The BCM activates the buzzer for up to 10 seconds at intervals of 0.5 sec. ON/0.5 sec. OFF and
turns on the smart key warning indicator on the instrument cluster.
If a smart key is found, no operation is performed. 1.
2.
3.
4.
5.
Any door except the driver door is opened and then closed.
The smart key not detected warning is not activated.
the smart key not detected warning signal to the BCM and instrument cluster through B-CAN.
The smart key not detected warning is activated.
- Smart key searching at intervals of 3 seconds using the interior antenna. 1.
2.
3.

(2) Smart Key Detected Warning (Smart Key Found Inside Vehicle)
Smart key deactivation warning
The ignition is turned OFF or ACC is turned ON.
A verified smart key found in the vehicle with all doors (including tailgate) closed.
The REKES LOCK or passive LOCK signal is input with a valid smart key from the outside the
vehicle.
The SKM sends the theft deterrent mode signal to the BCM through B-CAN and the verified smart
key is found inside the vehicle.
The SKM sends the smart key detected warning to the BCM and instrument cluster through B-CAN.
The BCM activates the buzzer for up to 10 seconds at intervals of 0.5 sec. ON/0.5 sec. OFF and
turns on the smart key detected warning indicator on the instrument cluster. 1.
2.
3.
4.
5.
6.
Smart key inside vehicle warning
The ignition is turned ON or OFF, or the ACC is turned ON.
A verified smart key found only in the vehicle (including emergency slot) with all doors (including
tailgate) closed.
The passive LOCK signal is input without a valid smart key from the outside the vehicle.
The SKM sends the theft deterrent mode signal to the BCM through B-CAN and the verified smart
key is found inside the vehicle.
The SKM sends the smart key detected warning to the BCM and instrument cluster through B-CAN.
The BCM activates the buzzer for up to 10 seconds at intervals of 0.5 sec. ON/0.5 sec. OFF and
turns on the smart key detected warning indicator on the instrument cluster. 1.
2.
3.
4.
5.
6.Smart key detected warning deactivation conditions
- The theft deterrent mode is deactivated.
Smart key detected warning deactivation conditions
- No smart key is found inside the vehicle when a door is opened and then closed.

8712-03
(4) Smart key battery discharge warning (3) Smart key verification fail warning
When the verification is requested for ignition status change or engine starting and no verified smart key
is in the vehicle, the SKM sends the "smart key verification status" signal, which indicates that the
verification has failed, for up to 10 sec. until the verification fail conditions are deactivated. for up to 10
seconds. until the verification fail conditions are deactivated.
Verification fail detection and transmission conditions
When the ignition status is changed after a smart key is verified by the START/STOP switch ON
input, the SKM sends the verification status for 10 sec. -Normally, the smart key verification warning is one of the smart key fail conditions. -
Ignition status change
(OFF -> ACC) / (OFF -> IGN)/(ACC -> IGN) / (IGN -> engine ON) *
If above conditions are met again, the SKM re-verifies a smart key and sends the verification status
for another 10 seconds.
When the ignition status is changed by the transponder verification while the smart key status is sent
through the B-CAN, the SKM sends the smart key verification signal and also sends the transponder
verification signal for 10 seconds. -
-
If low smart key battery is detected during the verification process for ignition status change or engine
start, the SKM sends the signal for "smart key battery low voltage warning" to the BCM and instrument
cluster through the B-CAN for up to 10 sec. until the warning condition is deactivated.
Smart key battery discharge confirmation and deactivation
If the smart key battery low voltage is confirmed, the SKM sends the smart key battery low voltage
warning signal.
If the smart key battery is in normal condition, the SKM sends the smart key battery low voltage
warning deactivation signal.
The smart key is the last used key. -
-
*
(5) Transponder verification fail warning
If a verified smart key is not found by the key verification process, the SKM sends the information that
indicates the key is not verified to the instrument cluster through the B-CAN for up to 10 seconds until
the warning condition is deactivated.
The SKM sends the transponder verification warning when the verification has failed with the smart
key inserted into the immobilizer holder. -
Transponder verification fail detection and transmission conditions
When the ignition status is changed after the transponder is verified by the START/STOP switch ON
input, the SKM sends the transponder verification status for 10 sec. -

Ignition status change*
If above conditions are met again, the SKM re-verifies the transponder and sends the verification
status for another 10 sec.
When the ignition status is changed by a smart key verification while the transponder verification is
processed, the SKM sends the signal for [transponder verification fail], and sends the smart key
verification status for 10 sec. -
-
(6) Transmission position warning
When the gear selector lever is in a position other than P or N with IGN ON and engine started, the
SKM sends the [gear position warning] signal to the instrument cluster through the BCAN for up to 10
sec. until the operating conditions are deactivated.
Transmission position warning deactivation
When re-attempting to start with IGN1 ON and transmission in P or N -
(7) ESCL JAM warning
The SKM transmits the warning active command to the BCAN through the BCAN signals such as ESCL
NOT LOCKED warning signal or ESCL JAM warning signal within 10 seconds or until the active
command deactivation conditions will be met, if jam is occurred when the electric steering motor is
locked/unlocked.
Failure Detecting Conditions
When the UNLOCK retry occurs after ESCL LOCK command, the ESCL LOCK is performed.
- The UNLOCK retry is possible up to 2 times automatically. If the UNLOCK retry occurs 3 times
in succession, the ESCL NOT LOCKED warning is triggered.
- Reactivates when the ESCL LOCK conditions are met.
When the LOCK retry occurs after ESCL LOCK command, the command will be overridden without
retry.
- After the command is overridden, the ESCL NOT LOCKED warning is triggered.
- Reactivates when the LOCK conditions are met by pressing the START/STOP switch after
ESCL UNLOCK.
When the LOCK retry occurs after ESCL UNLOCK command, the ESCL UNLOCK is performed.
- The LOCK retry is possible up to 2 times automatically. If the LOCK retry occurs 3 times in
succession, the ESCL JAM warning is triggered.
- Reactivates when the ESCL UNLOCK conditions are met by pressing the START/STOP
switch.
When the UNLOCK retry occurs after ESCL UNLOCK command, the command will be overridden
without retry.
- After the command is overridden, the ESCL JAM warning is triggered.
- Reactivates when the UNLOCK conditions are met by pressing the START/STOP switch after
ESCL LOCK. 1.
2.
3.
4.

(10) Brake not working alert
The SKM sends the brake not working alert signal for 10 sec. every time the ignition status is changed
after the 1st cycle (OFF-ACC-IGN-ACC-OFF)
while the brake is not operated.
when the brake pedal is depressed, the system is reset and alert deactivation signal is sent.
when the 10 min. timer is terminated -
-
(11) Smart key slot detection alert
The SKM sends the smart key slot detection alert signal for 10 sec. when a smart key inserted into
the slot is detected with IGN OFF and the driver's door open. -
(12) SKM alert priority
1 Smart key out alarm Outside
1
2 Smart key reminder alarm Outside
3 Smart key verification failure alarm Inside
2 4 Transponder verification fail alert Inside
5 Smart key battery low voltage alert Inside
6 Transmission position alert Inside
7 SKM error alert Inside
8 Brake alert Inside
9 Clutch alert Inside
10 Smart key slot reminder alarm Inside 1
Warning deactivation conditions
Warning transmission conditions
Warning deactivation conditions
when the smart key is removed, the alert deactivation signal is sent.
when the 10 min. timer is terminated -
-