alternator SSANGYONG MUSSO 1998 Workshop Owner's Manual

OM600 ENGINE MECHANICAL 1B3-65
11. Remove the alternator bracket (16).
9. Disconnect the pipes of power steering pump and remove
the belt pulley.
Notice
Be careful not to lose the key.
10. Remove the nut and pull out the bolt and then remove the
power steering pump.
12. Remove the fuel filter.

1B3-68 OM600 ENGINE MECHANICAL
Tightening Torque25 Nm 5. Install the flange, vibration damper and crankshaft belt
pulley.
Notice
Replace front radial seal if necessary.
6. Install the alternator bracket.
25 Nm Front
Side
7. Install the alternator
Tightening TorqueUpper - 25 Nm
Low - 25 Nm
8. Install the cylinder head cover.
Tightening Torque 10 Nm
9. Tighten the injection pump mounting bolts.
Tightening Torque 23 Nm

1D3-8 OM600 ENGINE COOLING
COOLANT PUMP HOUSING
Preceding Work : Removal of coolant pump
Removal of thermostat
Removal of alternator
1 Gasket ................................................... Replace
2 Coolant Pump Housing
3 Connector
4 Bolt........................................................... 10 Nm5 Coolant Hose
6 Return Pipe
7 O-Ring
8 Temperature Sensor
Notice
The bolt on the arrow should be installed last.

SECTION 1E1
M162 ENGINE ELECTRICAL
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1E1-1
Alternator Specifications . . . . . . . . . . . . . . . . 1E1-1
Starting Motor Specifications . . . . . . . . . . . . 1E1-2
Battery Specifications . . . . . . . . . . . . . . . . . . 1E1-2
Fastener Tightening Specifications . . . . . . . . 1E1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1E1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1E1-3
Maintenance and Repair . . . . . . . . . . . . . . 1E1-4
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1E1-4
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-4
Starting Motor . . . . . . . . . . . . . . . . . . . . . . . . 1E1-5
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-6
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-7
Ignition Cable . . . . . . . . . . . . . . . . . . . . . . . . 1E1-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 1E1-12
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E1-12
SPECIFICATIONS
ALTERNATOR SPECIFICATIONS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Application
Output Voltage
Current
Resistance Between Rotor Core and Slip RingDescription
12 - 14 V
115 A
¥ W

1E1-2 M162 ENGINE ELECTRICAL
N·m
14 - 18
4 - 5
45 - 50
12 - 15
6 - 7
35 - 48
12 - 18
12 - 18
12 - 18
9 - 11
9 - 11
25 - 30
STARTING MOTOR SPECIFICATIONS
Application
Voltage
Output PowerDescription
12 V
1.7 KW
BATTERY SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Capacity
Specific Gravity
Max. Tolerance Between CellsDescription
75 AH
³ 1.24
³ 0.04
Application
Alternator Terminal B+Nut
Alternator Terminal D+Nut
Alternator Combinction Bolt
Battery Cable Nut on Starting Motor
Electric Wire Nut on Starting Motor
Starting Motor Mounting Nut
Battery Mounting Bracket Nut
Battery Negative Cable
Battery Positive Cable
Ignition Cable Cover Bolt
Ignition Cable Bolt
Spark plug

1E1-4 M162 ENGINE ELECTRICAL
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ALTERNATOR
Preceding Work : Removal of the drivebelt
Removal & Installation Procedure
1. Disconnect the negative battery terminal.
2. Unscrew the nut and disconnect the terminal (1).
Installation Notice
1 Terminal (B+)
2 Terminal (D+)
3 Combination Bolt
4 Alternator
3. Unscrew the nut and disconnect the terminal (2).
Installation Notice
Tightening Torque 14 - 18 Nm
4. Unscrew the combination bolt (3).
Installation Notice
Tightening Torque 4 - 5 Nm
5. Remove the alternator.
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 42 - 50 Nm

SECTION 1E2
M161 ENGINE ELECTRICAL
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1E2-1
Alternator Specifications . . . . . . . . . . . . . . . . 1E2-1
Starting Motor Specifications . . . . . . . . . . . . 1E2-2
Battery Specifications . . . . . . . . . . . . . . . . . . 1E2-2
Fastener Tightening Specifications . . . . . . . . 1E2-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1E2-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1E2-3
Maintenance and Repair . . . . . . . . . . . . . . 1E2-4
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1E2-4
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-4
Starting Motor . . . . . . . . . . . . . . . . . . . . . . . . 1E2-5
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-6
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-7
Ignition Cable . . . . . . . . . . . . . . . . . . . . . . . . 1E2-9
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 1E2-12
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E2-12
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
SPECIFICATIONS
ALTERNATOR SPECIFICATIONS
Application
Output Voltage
Current
Resistance Between Rotor Core and Slip RingDescription
12 - 14 V
115 A
¥ W

1E2-2 M161 ENGINE ELECTRICAL
N·m
14 - 18
4 - 5
45 - 50
12 - 15
6 - 7
35 - 48
12 - 18
12 - 18
12 - 18
9 - 11
9 - 11
25 - 30
STARTING MOTOR SPECIFICATIONS
Application
Voltage
Output PowerDescription
12 V
1.2 KW
BATTERY SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Capacity
Specific Gravity
Max. Tolerance Between CellsDescription
90 Ah
³ 1.24
³ 0.04
Application
Alternator Terminal B+Nut
Alternator Terminal D+Nut
Alternator Combinction Bolt
Battery Cable Nut on Starting Motor
Electric Wire Nut on Starting Motor
Starting Motor Mounting Nut
Battery Mounting Bracket Nut
Battery Negative Cable
Battery Positive Cable
Ignition Cable Cover Bolt
Ignition Cable Bolt
Spark plug

1E2-4 M161 ENGINE ELECTRICAL
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ALTERNATOR
Preceding Work : Removal of the drivebelt
Removal & Installation Procedure
1. Disconnect the negative battery terminal.
2. Unscrew the nut and disconnect the terminal (1).
Installation Notice
1 Terminal (B+)
2 Terminal (D+)
3 Combination Bolt
4 Alternator
3. Unscrew the nut and disconnect the terminal (2).
Installation Notice
Tightening Torque 14 - 18 Nm
4. Unscrew the combination bolt (3).
Installation Notice
Tightening Torque 4 - 5 Nm
5. Remove the alternator.
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 42 - 50 Nm

SECTION 1E3
OM600 ENGINE ELECTRICAL
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1E3-1
General Specifications . . . . . . . . . . . . . . . . . 1E3-1
Maintenance and Repair . . . . . . . . . . . . . . 1E3-2
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1E3-2
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Application
Alternator
Starter
Glow PlugDescription
12V - 75A
12V - 2.2kW
11.5V
SPECIFICATIONS
GENERAL SPECIFICATIONS
Glow Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E3-2
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1E3-6
Starter Motor . . . . . . . . . . . . . . . . . . . . . . . . . 1E3-8