steering wheel SSANGYONG MUSSO 2003 Owner's Guide

8B-18 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
MAINTENANCE AND REPAIR ON-VEHICLE SERVICE AIR BAG MODULE Removal & Installation Procedure
1. Remove the steering wheel rid (LH,RH) with a screwdriver.Installation Notice Each position mark (LH,RH) is stamped on the inner surface of the rids.
Tightening Torque 7 - 11 Nm
3. Disconnect the connectors and remove the air bag module.
4. Installation should follow the removal procedure in thereverse order.
2. Unscrew the bolts from both sides.
Installation Notice

8B-20 SUPPLEMENTAL RESTRAINT SYSTEM(SRS) Removal & Installation Procedure preceding work : removal of steering wheel
1. Turn the ignition switch to “OFF” position and disconnectthe battery negative cable. Start the procedure after waiting over 3oseconds.
2. Unscrew 3 screws from lower cover on steering column shaft and remove the lower cover.
3. Unscrew 4 screws from clock spring and remove the clock
spring
Installation Notice
Don’t try to repair and modify the clock spring.
When aligning the neutral position, turn to clockwise until it stops, and turn to counter clockwise until the marks are aligned

5-98 ELECTRICAL WIRING DIAGRAMS
16. ECS
1) POWER SUPPLY, GROUND, SENSOR (WHEEL'G, VERTICAL, LATERAL) CIRCUIT Main - Engine Engine - Main DLC Connector - Main Main - Floor MainMain
C103 (21Pin, White)
C109 (16Pin, Black)
C211 (14Pin, Black)
C303 (14Pin, White) G201 G302
b. CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
a. CONNECTOR INFORMATION
CONNECTOR(NUMBER)
CONNECTING. WIRING HARNESSCONNECTOR POSITION
Inside The Engine Room Fuse Block Under The Coolant Reservoir Tank Beside The Steering Column Beside The I/P Relay BlockRight The I/P Fuse Block Beside The Left Rear Speaker
C103
W/H MAIN
ECS CLUSTER
1
14 13 2611
2
29 38
28
13 2021
39 434842
C303
W/H MAIN
12 45
78 3
9 101112 13 6
14
C109
W/H ENGINEC211
W/H DLC
LATERAL SENSOR
VERTICAL SENSOR
231
WHEEL 'G'
SENSOR
231
G201 G302
LW
LB
YR
30
18
YR
R R GW GB GB
B+
5V
LAMP
16
13
SIG
Ef8
60A
F16 15A
Ef2 80A
ECS
Relay
30
86
87
85
1
C103
1 C303
F24
10A
F22 10A
B
12 14
B
GND
YW
11
5V
GND
9 C303 Cluster
(ECS WarningLamp)4
C303
Y Y
Cluster
(Speed Meter)
"17"
23 ECS Control Unit
7C211
13
C303
G G G
DLC
"1"
+
3
BY
7
SIG
1BL
YW BY
YW BY
BL
8
_
2
85 6
C303
15 13 14C109
Wheel 'G' Sensor
+
3
20
SIG
1
YW GBr GBr
BG
GY
_
2
Lateral Sensor
+
3
10
SIG
1
YW BG GY_
2
Vertical Sensor
7 C303
12 C303
30 BAT+
15 IGN 1
31 GND
1
2910 1213
12
11
34
56
71 4
8

5-186 ELECTRICAL WIRING DIAGRAMS
41. ABS 5.3 CIRCUITa. CONNECTOR INFORMATION
b. CONNECTOR IDENTIFICATION SYMBOL & PIN NUMBER POSITION
C109
W/H ENGINE C302
W/H MAIN EBCM (ABS)
WHEEL SPEED SENSOR ACCELERATION
SENSOR
TOD
(BTRE A/T) (MB A/T,M/T) STOP LAMP SWITCH
C102
W/H MAIN C211
W/H DLC
CLUSTER
1234 5678
9 101112
13 14 15 16
12 34
5678910
11 12 13 14 15 16
1234567891011 12
13 14 15
212019
18
17
16
22 23 24 25 2627 28 29 30 31123
12910 1213
12 11
34567 14
812
A1 A9 A8
A18
B1
B6 B5
B12
12 3421
11 2
29 38
28
13 2021
39 434842
Main - Engine Engine - Main DLC Connector - Main Main - FloorMain
C102 (2Pin, Colorless)C109 (16Pin, Black) C211 (14Pin, Black) C302 (16Pin, White) G206
CONNECTOR(NUMBER)
CONNECTING. WIRING HARNESSCONNECTOR POSITION
Inside The Engine Room Fuse Block Under The Coolant Reservoir Tank Beside The Steering ColumnBeside The I/P Relay Block Beside The ABS Module
F22
RRGLB
BW
2 C102 18
17 18 20
15
B+ B+
G206
16
19
BB
12 LH12RH
SIG
GND
GND IGN1
14
SIG3010 SIG285V
SIG
7 6 5
4
BrB BrB BrBBrB
BrWBrW
BrWBrW
Front Wheel Speed Sensor
12 LH12RH
SIG SIG
98 1
2
13
BrB BrB BrB RY
C302
BrB
BrWBrW
BrWBrW
3
41
2
Rear Wheel Speed Sensor
C109
YW
GY LY GW WR
21
8
9 ABS EBD Stop Lamp
Switch
"2(M/T, MB A/T)"
"4(BTRA A/T)"
11 WY
WY
DLC
"8"
Cluster
TOD
"A13" EBCM
14
C211
G
Acceleration Sensor
1 2
3
30 BAT+
15 IGN 1
31 GND
Ef1 60A10AF3
10A
1 23
4