maintenance reset SUBARU FORESTER 2000 SF / 1.G Owners Manual

Audio5-9
–
CONTINUED –

Automatic tuning (SCN)
Press the “SCN ” b utton to c hang e the rad io to the SCAN mod e. In th is
mod e, the rad io sc ans throug h the rad io b and until a station is found .
The rad io will stop at the station for five sec ond s while d isp laying the fre-
q uenc y, after whic h sc anning will c ontinue until th e entire b and has b een
sc anned from the low end to the hig h end .
Press the “SCN ” b utton ag ain to c anc el the SCAN mod e and to stop o n
any d isp layed freq uenc y.
When the “SCN ” b utton is p ressed for automatic tuning , stations a re
sc anned in the d irec tion of low freq uenc ies to hig h freq uenc ies only.
Automatic tuning may not func tion p rop erly if the s tation rec ep tion is
weakened b y d istanc e from the station or p roximity to tall b uild ing s and
hills. Selecting preset stations
Presetting a station with a p reset b utton allows yo u to selec t that station
in a sing le op eration. Up to six AM and FM stations eac h may b e p reset.
How to preset stations
1. Press the FM/AM selec tion switc h to selec t either FM or AM rec ep tion.
2. Press the “SCN ” b utton or tune the rad io manually until the d esire d
station freq uenc y is d isp layed .
3. Press one of the p reset b uttons for at least two seconds to store the
freq uenc y. The freq uenc y of the station will flash onc e on the d isp lay at
this time. If the b utton is p ressed for less than t wo sec ond s, the p rec ed -
ing selec tion will remain in memory. NOTE
If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stationsstored in the preset buttons are cleared. If this occurs, it is neces-sary to reset the preset buttons.

Audio5-13
–
CONTINUED –

Display mode
You c an selec t either the time d isp lay mod e or func tion d isp lay mod e b y
p ressing the “DISP/CLK ” b utton when the ig nition switc h is either “ACC ”
or “ON ” p osition.
Time display mode
When the time d isp lay mod e is selec ted , the time d i sp lay takes p rior-
ity of the func tion d isp lay. The time is shown on t he d isp lay whenever
the ig nition switc h is “ACC ” or “ON ” p osition.
When the rad io is turned on or the station is c hang ed d uring the time
d isp lay mod e, the time d isp lay is rep lac ed b y the f req uenc y d isp lay.
However, after the freq uenc y has b een d isp layed for five sec ond s, it
is rep lac ed b y the time d isp lay ag ain. Function display mode
When the func tion d isp lay mod e is selec ted , the tim e is not shown on
the d isp lay. The d isp lay ind ic ates the c urrent func tion only.
When the rad io is turned off d uring the func tion d i sp lay mod e, the
b ac k-up lig ht on the d isp lay g oes out.
Setting the time
1. Turn the ig nition switc h to “ACC ” or “ON ”.
2. To adjust hour: Press the “DISP ” b utton and the “TUNING ” b utton
ind ic ated with “ ” tog ether to ad vanc e the hours in one-hour inc remen ts.
Keep ing the b uttons p ressed ad vanc es the hours q uic kly.
3. To adjust minute: Press the ”DISP ” b utton and the “TUNING ” b utton
ind ic ated “
 ” tog ether to ad vanc e the minutes in one-minute inc r ements.
Keep ing the b uttons p ressed ad vanc es the minutes q u ic kly.
NOTE
If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, the time set-ting will be cleared. If this occurs, it is necessary to reset the time.