ignition SUBARU IMPREZA 2002 2.G Workshop Manual
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2002, Model line: IMPREZA, Model: SUBARU IMPREZA 2002 2.GPages: 390, PDF Size: 4.33 MB
Page 225 of 390

Starting and operating
7-24
CAUTION
If the warning light behaves as follows, the
ABS system may not be working properly. When the warning light is on, the ABS func-
tion shuts down; however, the conventional
brake system continues to operate normally. The warning light does not come on when
the ignition switch is turned to the “ON” posi-
tion. The warning light comes on when the igni-
tion switch is turned to the “ON” position, but
it does not go out even when the vehicle speed exceeds approximately 8 mph (12km/h). The warning light comes on during driving.
If these occur, have the ABS system repairedat the first available opportunity by your
SUBARU dealer.
NOTE If the warning light behavior is as described
below, the ABS system may be considered nor- mal. The warning light comes on right after the
engine is started but goes out immediately,remaining off.
The warning light remains on after the engine
has been started, but it goes out when the
vehicle speed reaches about 8 mph (12 km/h). The warning light comes on during driving, but
it goes out immediately and remains off.
Page 229 of 390

Starting and operating
7-28
HG0312
3. Push the control lever downward in the “SET,
COAST” direction and release it. Then release the
accelerator pedal.
The vehicle will maintain the desired speed.
Vehicle speed can be temporarily increased while
driving with the cruise control activated. Simply de-
press the accelerator pedal to accelerate the ve-
hicle. When the accelerator pedal is released, the
vehicle will return to and maintain the previous cruis-ing speed.
To temporarily cancel the cruise con- trol
There are four ways to cancel the cruise control tem- porarily:
Depress the brake pedal.
Pull the control lever in the “CANCEL” direction. (if
so equipped) Depress the clutch pedal (manual transmission
vehicles only). Shift the selector lever into the “N” position (auto-
matic transmission vehicles only).
To resume the cruise control after it has been tem- porarily canceled and with vehicle speed of about
20 mph (32 km/h) or more, push the control lever
upward in the “ACCEL, RESUME ” direction to return
to the original cruising speed automatically.
To turn off the cruise control
There are two ways to turn off the cruise control: Push the main switch again.
Turn the ignition switch to the “ACC” or “LOCK”
position (but only when the vehicle is completely stopped). To change the cruising speed
To increase the speed
1. Push the control lever upward in the “ACCEL, RE-
SUME” direction and hold it until the vehicle reaches
Page 235 of 390

Driving tips
8-4
Catalytic converter
HG8000BA
Turbo models
HB3003BA
Non-turbo models
The catalytic converter is installed in the exhaust
system. It serves as catalyst to reduce HC, CO and
NOx in exhaust gases, thus providing cleaner ex- haust.
To avoid damage to the catalytic converter: Use only unleaded fuel. Even a small amount of
leaded fuel will damage the catalytic converter. Never start the engine by pushing or pulling the
vehicle. Avoid racing the engine.
Never turn off the ignition switch while the vehicle
is moving. Keep your engine tuned-up. If you feel the engine
Page 271 of 390

In case of emergency
9-2
If you park your vehicle in case of an emergency
HG3004AA
The hazard warning flasher should be used in day
or night to warn other drivers when you have to parkyour vehicle under emergency conditions.
Avoid stopping on the road. It is best to safely pull
off the road if a problem occurs.
The hazard warning flasher can be activated
regardless of the ignition switch position.
Turn on the hazard warning by pushing the hazard
warning flasher switch. Turn it off by pushing the switch again.NOTE When the hazard warning flasher is on, the turn
signals do not work.
Page 288 of 390

In case of emergency
9-19
– CONTINUED –
3. Secure the vehicle onto the carrier properly with safety chains. Each of safety chain should be
equally tightened and care must be taken not to pull
the chains so tightly that the suspension bottomsout.
CAUTION
If your vehicle has a front underspoiler and rear underspoiler (both optional), be carefulnot to scrape them when placing the vehicleon the carrier and when removing the vehicle
from the carrier.
Towing with all wheels on the ground
HG9001AA
1. Check the transmission and differential oil levels
and add oil to bring it to the upper level if necessary.
2. Release the parking brake and put the transmis-sion in neutral.
3. The ignition switch should be in the “ACC” posi-
tion while the vehicle is being towed.
4. Take up slack in the towline slowly to prevent
damage to the vehicle.
WARNING
Never turn the ignition switch to the “LOCK”
position while the vehicle is being towed be-
cause the steering wheel and the direction ofthe wheels will be locked. Remember that the brake booster and pow-
er steering do not function when the engine is not running. Because the engine is turned off,
it will take greater effort to operate the brakepedal and steering wheel.