light SUBARU IMPREZA 2003 2.G Owners Manual

In case of emergency
9-14
WARNING
Never place a tire or tire changing tools in the
passenger compartment after changing
wheels. In a sudden stop or collisions, looseequipment could strike occupants and cause
injury. Store the tire and all tools in the proper place.Jump starting
WARNING

Battery fluid is SULFURIC ACID. Do not let it
come in contact with the hooks, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush
the exposed area with water immediately. Get
medical help if the fluid has entered your hooks.
If battery fluid is accidentally swallowed, im-
mediately drink a large amount of milk or wa-
ter, and obtain immediate medical help. Keep everyone including children away from
the battery. The gas generated by a battery explodes if a
flame or spark is brought near it. Do not
smoke or light a match while jump starting. Never attempt jump starting if the dis-
charged battery is frozen. It could cause thebattery to burst or explode. Whenever working on or around a battery,
always wear suitablehookprotectors, and re- move metal objects such as rings, bands or
other metal jewelry.

In case of emergency
9-15
– CONTINUED –
Be sure the jumper cables and clamps on
them do not have loose or missing insulation.
Do not jump start unless cables in suitablecondition are available. A running engine can be dangerous. Keep
your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other
moving engine parts. Removing rings,watches and ties is advisable.
When your vehicle does not start due to a run down
(discharged) battery, the vehicle may be jump
started by connecting your battery to another bat-
tery (called the booster battery) with jumper cables.
Jump starting is dangerous if it done incorrectly. If
you are unsure about the proper procedure for jump
starting, consult a competent mechanic.
How to jump start
1. Make sure the booster battery is 12 volts and the
negative terminal is grounded.
2. If the booster battery is in another vehicle, do notlet the two vehicles touch.
3. Turn off all unnecessary lights and accessories.
4. Connect the jumper cables exactly in the se-
quence illustrated.

Appearance care
10-2
Exterior care Washing
The best way to preserve your vehicle ’s beauty is
frequent washing. Wash the vehicle at least once a
month to avoid contamination by road grime.
Wash dirt off with a wet sponge and plenty of luke-
warm or cold water. Do not wash the vehicle with hot
water and in direct sunlight.
Salt, chemicals, insects, tar, soot and bird droppings
should be washed off by using a light detergent, as
required. If you use a light detergent, make certain
that it is a neutral detergent. Do not use strong soap or chemical detergents. All cleaning agents should
be promptly flushed from the surface and not al-
lowed to dry there. Rinse the vehicle thoroughly with
plenty of lukewarm water. Wipe the remaining water
off with a chamois or soft cloth. NOTE When having your vehicle washed in an auto- matic car wash, make sure beforehand that thecar wash is of suitable type. If the vehicle is
equipped with a rear/roof spoiler or rear wiper, itmay be damaged by car wash brushes or otherequipment.
CAUTION
When washing the vehicle, the brakes may
get wet. As a result, the brake stopping dis-
tance will be longer. To dry the brakes, drivethe vehicle at a safe speed while lightly press- ing the brake pedal to heat up the brakes. Do not wash the engine compartment and
area adjacent to it. If water enters the engineair intake, electrical parts or the power steer-
ing fluid reservoir, it will cause engine trouble
or faulty power steering respectively.
Washing the underbody
Chemicals, salts and gravel used for deicing road
surfaces are extremely corrosive, accelerating the
corrosion of underbody components, such as theexhaust system, fuel and brake lines, brake cables,floor pan and fenders, and suspension.
Thoroughly flush the underbody and inside of the
fenders with lukewarm or cold water at frequent in-
tervals to reduce the harmful effects of such agents.
Using a warm water washer
Keep a good distance of 12 in (30 cm) or more
between the washer nozzle and the vehicle.

Appearance care
10-3
– CONTINUED –
Do not wash the same area continuously.
If a stain will not come out easily, wash by hand.
Some warm water washers are of the high tempera-
ture, high pressure type, and they can damage or
deform the resin parts such as mouldings, or causewater to leak into the vehicle. Waxing and polishing
Always wash and dry the vehicle before waxing and polishing.Use a good quality polish and wax and apply them
according to the manufacturer ’s instructions. Wax or
polish when the painted surface is cool.
Be sure to polish and wax the chrome trim, as well
as the painted surfaces. Loss of wax on a painted
surface leads to loss of the original luster and also
quickens the deterioration of the surface. It is rec-
ommended that a coat of wax be applied at least
once a month, or whenever the surface no longer re-
pels water. If the appearance of the paint has diminished to the
point where the luster or tone cannot be restored,
lightly polish the surface with a fine-grained com-
pound. Never polish just the affected area, but in-
clude the surrounding area as well. Always polish in
only one direction. A No. 2000 grain compound is recommended. Never use a coarse-grained com-
pound. Coarser grained compounds have a smallergrain-size number and could damage the paint. Af-
ter polishing with a compound, coat with wax to re-
store the original luster. Frequent polishing with a
compound or an incorrect polishing technique will
result in removing the paint layer and exposing the
undercoat. When in doubt, it is always best to con-tact your SUBARU dealer or an auto paint specialist. NOTE Be careful not to block with windshield washer nozzles with wax when waxing the vehicle.
Cleaning aluminum wheels
Promptly wipe the aluminum wheels clean of any
kind of grime or agent. If dirt is left on too long, it
may be difficult to clean off. Do not use soap containing grit to clean the
wheels. Be sure to use a neutral cleaning agent, and
later rinse thoroughly with water. Do not clean the
wheels with a stiff brush or expose them to a high- speed washing device. Clean the vehicle (including the aluminum wheels)
with water as soon as possible when it has been
splashed with sea water, exposed to sea breezes, or
driven on roads treated with salt or other agents.

Appearance care
10-6
wear prematurely. Regular cleaning with a soft,
moist, natural fiber cloth should be performed
monthly, taking care not to soak the leather or allowwater to penetrate the stitched seams.A mild detergent suitable for cleaning woolen fab-
rics may be used to remove difficult dirt spots, rub-
bing with a soft, dry cloth afterwards to restore the
luster. If your SUBARU is to be parked for a long
time in bright sunlight, it is recommended that the
seats and headrests be covered, or the windows
shaded, to prevent fading or shrinkage.
Minor surface blemishes or bald patches may be
treated with a commercial leather spray lacquer. You will discover that each leather seat section will de-
velop soft folds or wrinkles, which is characteristic of
genuine leather. Synthetic leather upholstery
The synthetic leather material used on the SUBARU may be cleaned using mild soap or detergent and
water, after first vacuuming or brushing away loose
dirt. Allow the soap to soak in for a few minutes and
wipe off with a clean, damp cloth. Commercial foam-type cleaners suitable for synthetic leather materials
may be used when necessary. NOTE Strong cleaning agents such as solvents, paint
thinners, window cleaner or gasoline must neverbe used on leather or synthetic interior materials.

Maintenance and service
11-2
Tire inspection 11-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire pressures and wear 11-42 . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel balance 11-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wear indicators 11-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire rotation 11-46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire replacement 11-47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel replacement 11-48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel covers 11-49 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aluminum wheels (If equipped) 11-50 . . . . . . . . . . . . . . . .
Windshield washer fluid 11-50 . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement of windshield wiper blades 11-51 . .
Battery 11-54
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses 11-56
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main fuse 11-59
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation of accessories 11-60 . . . . . . . . . . . . . . . . . . . . . . .
Replacing bulbs 11-61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight 11-62
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front turn signal light and parking light 11-64 . . . . . .
Front fog light (if equipped) 11-68 . . . . . . . . . . . . . . . . . . . . .
Front side marker light 11-69 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear combination lights 11-70 . . . . . . . . . . . . . . . . . . . . . . . . . .
License plate light 11-72 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dome light, map light and cargo area light 11-73 . . .
Trunk light 11-74
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High mount stop light 11-74 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance and service
11-6
2. Release the secondary hood release located
under the front grille by moving the lever toward theleft.Lift up the hood, release the hood prop from its
retainer and put the end of the hood prop into theslot in the hood.
To close the hood: All models except WRX:
1. Lift the hood slightly and remove the hood prop
from the slot in the hood and return the prop to its
retainer.
2. Lower the hood until it approaches about 6 in.
(15 cm) from the closed position and let it drop.

Maintenance and service
11-7
– CONTINUED –
WRX:
1. Lift the hood slightly and remove the hood prop
from the slot in the hood and return the prop to its
retainer.
2. Lower the hood until it approaches about 12 in.
(30 cm) from the closed position and let it drop.
After closing the hood, be sure the hood is securelylocked.
If this does not close the hood, release it from a
slightly higher position. Do not push the hood forci-
bly to close it. It could deform the metal.
WARNING
Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block
your view, which may cause an accident and
serious bodily injury.

Maintenance and service
11-12
ing washer after the oil has completely drained out.
1) Oil filter
6. Remove the oil filter with an oil filter wrench.
7. Before installing a new oil filter, apply a thin coatof engine oil to the seal.
8. Clean the rubber seal seating area of the lower
crank case and install the oil filter by hand turning.
Be careful not to twist or damage the seal.
9. Tighten it approximately two-thirds of a turn after the seal makes contact with the lower crank case.
CAUTION
Never over tighten the oil filter because that can result in an oil leak.
10. Pour engine oil through the filler neck.
Oil capacity (guideline): Non-turbo models: 4.2 US qt (4.0 liters, 3.5 Imp qt)
Turbo models: 4.8 US qt (4.5 liters, 4.0 Imp qt)
The oil quantity indicated above is only guideline.
The necessary quantity of oil depends on the quan- tity of oil that has been drained. The quantity of
drained oil differs slightly depending on the temper-
ature of the oil and the time the oil is left flowing out.
After refilling the engine with oil, therefore, you must
the dipstick to confirm that the level is correct.
11. Start the engine and make sure that no oil leaks
appear around the filter ’s rubber seal and drain
plug.
12. Run the engine until it reaches the normal oper-
ating temperature. Then stop the engine and wait a
few minutes to allow the oil drain back. Check the oil
level again and if necessary, add more engine oil.

Maintenance and service
11-36
have the vehicle checked at your SUBARU
dealer.Never use different brands of clutch fluid to-
gether. When clutch fluid is added, be careful not to
allow any dirt into the tank.
Recommended clutch fluid
FMVSS No. 116, fresh DOT 3 or 4 brake fluidBrake booster If the brake booster does not operate as described
below, have it checked by your SUBARU dealer.
1. With the engine off, depress the brake pedal sev-
eral times, applying the same pedal force each time.
The distance the pedal travels should not vary.
2. With the brake pedal depressed, start the en-
gine. The pedal should move slightly down to the
floor.
3. With the brake pedal depressed, stop the engine
and keep the pedal depressed for 30 seconds. The pedal height should not change.
4. Start the engine again and run for about one min-
ute then turn it off. Depress the brake pedal several
times to check the brake booster. Brake booster op-
erates properly if the pedal stroke decreases with
each depression.