4A2 SUZUKI GRAND VITARA 1999 2.G Service Workshop Manual

YH4
GRAND
vol.1
0A
0B
1A
1B
3
3A
3B1
3C
3C1
3D
3E
3F
4A2
4B
5
6
7A5A
5B
5C
5E1
6A1
6A2
6A4
6B
6C
6E1
6E2
6F1
6F2
6G
6G1
6H
6K
7A1
7B1
7C1
7D
7E
7F
8
8B
8C
8D
8G
9
10
10A
8A
10B
6-1ENGINE
General Information and
Diagnosis (G16 / J20)
General Information and
Diagnosis (H25)
Engine Mechanical (G16)
Engine Mechanical (H25)
Engine Mechanical (J20)
Engine Cooling
Engine Fuel
Engine and Emission Control
System (SFI for G16 / J20)
Engine and Emission Control
System (SFI for H25)
Ignition System (G16)
Ignition System (J20 / H25)
Cranking System
(Reduction Type)
Cranking System
(No-Reduction Type)
Charging System
Exhaust System
TRANSMISSION, CLUTCH
AND DIFFERENTIAL
Manual Transmission (Type 1)
Manual Transmission (Type 2)
Automatic Transmission
Clutch (Hydraulic Type)
Transfer
Differential (Front)
Differential (Rear)
BODY ELECTRICAL SYSTEM
Wiring Diagram
Lighting System
Instrumentation / Driver
Information
Windows, Mirrors, Security
and Lock
Immobilizer Control System
BODY SERVICE
RESTRAINT SYSTEM
Seat Belt
Air Bag System GENERAL INFORMATION
General Information
Maintenance and Lubrication
TABLE OF CONTENTS TABLE OF CONTENTS SECTIONSECTION
0B
HEATING AND AIR
CONDITIONING
Heater and Ventilation
Air Conditioning
STEERING, SUSPENSION,
WHEELS AND TIRES
Front End Alignment
Power Steering (P / S) System
Steering Wheel and Column
(Not Equipped with Air Bag)
Air Bag Steering Wheel
and Column
Front Suspension
Rear Suspension
Wheel and Tires
1A
3A 0A
1B
3B1
3C
3C1
3D
3E
3F36A16
6A2
6A4
6B
6C
6E1
6E2
6F1
DRIVE SHAFT / PROP. SHAFT
Front Drive Shaft / Shaft
Bearing, Oil Seal
Propeller Shaft
BRAKES
Brake Pipe / Hose / Master
Cylinder
Front Brakes
Parking and Rear Brakes
Antilock Brake System
4A2
4B
5
5A
5B
5C
5E1
6F2
6G
6G1
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8
8A
8B
8C
8D
8G
9
10
10A
10B
6-1
NOTE:
The screen toned Sections 6 ± 6K are included in Volume 2 and Section 8A is in Wiring
Diagram Manual.

YH4
GRAND
VITARA
4A2
1. Drive shaft oil seal
2. Double off set joint (DOJ)
3. Joint circlip
4. DOJ boot
5. Ball joint boot
6. Ball joint assembly (RH side)
7. Drive shaft assembly (LH side)
8. Left drive shaft
9. Drive shaft bearing circlip
10. Drive shaft bearing
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-1
SECTION 4A2
FRONT DRIVE SHAFT/SHAFT BEARING,
OIL SEAL
CONTENTS
GENERAL DESCRIPTION4A2- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS4A2- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table4A2- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Shaft Boot And Joint Check 4A2- 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE4A2- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive Shaft4A2- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shaft Bearing / Oil Seal4A2- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS4A2-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
The drive shaft joint is a constant velocity joint (C.V. joint) which slides in the axial direction. The joint is composed
of an outer race, cage, inner race and balls. In the turning direction, the joint rotates in the same way as a ball bear-
ing. The balls lock rotation completely and transmit drive. In addition this vehicle is also characterized by a function
that the shaft can slide through the balls in the grooves of the outer race in the extension / contraction direction of
the drive shaft.

YH4
GRAND
VITARA
4A2-2 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
DIAGNOSIS
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
When starting:
Abnormal Noise
Loose wheel nuts.

Loose drive shaft flange bolts.

Broken or otherwise damaged wheel
bearing.Tighten wheel nuts.
Tighten drive shaft flange bolts.
Replace or change.
When making turns:
Abnormal Noise
Grease leakage from drive shaft joint
boot.

Worn or broken drive shaft joint.Replace joint boot and apply grease.
Replace drive shaft joint.
When running:
Abnormal Noise
Broken drive shaft joint.

Poorly lubricated or worn drive
shaft joint.

Loose drive shaft flange bolts.

Deformed drive shaft oil seal.Replace drive shaft joint.
Lubricate or replace joint.
Tighten drive shaft flange bolts.
Replace.
Vibration
Worn drive shaft joint.

Deformed drive shaft oil seal.

Deformed drive shaft.Replace drive shaft joint.
Replace.
Replace.
DRIVE SHAFT BOOT AND JOINT CHECK
Check drive shaft boot for tear. If even a small tear is noted, replace
with new one.
Check drive shaft joint for wear, breakage and other damage and
replace if any defect exists.

YH4
GRAND
VITARA
1. Oil filler / level plug
2. Front drain plug
1. Circlip
2. Washer
1. Drive shaft flange
bolts and nuts
1. Oil seal
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-3
ON-VEHICLE SERVICE
DRIVE SHAFT
REMOVAL (LEFT SIDE)
1) Hoist vehicle and remove wheel.
2) Remove axle shaft drive flange.
3) Remove drive shaft circlip and front spindle thrust washer.
4) Remove drive shaft flange bolts and nuts.
5) Remove drive shaft assembly to differential side as shown in left
figure.
CAUTION:
To prevent breakage of boots (wheel side and differential
side), be careful not to bring them into contact with other
parts when removing drive shaft assembly.
6) Remove drive shaft thrust washer (vehicle with G16 or J20 en-
gine) from drive shaft and remove drive shaft oil seal as shown
in figure.
CAUTION:
Be careful not to cause damage to drive shaft joint.

YH4
GRAND
VITARA
1. Oil filler / level plug
2. Front drain plug
1. Circlip
2. Washer
1. Differential side joint
2. Tire lever
3. Front differential assembly
1. Oil seal 2
1
4A2-4 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
REMOVAL (RIGHT SIDE)
1) Hoist vehicle and remove wheel.
2) Drain differential gear oil.
3) Remove axle shaft drive flange.
4) Remove circlip and front spindle thrust washer.
5) Remove knuckle and wheel hub comp, refer to steps 5) to 7) and
9) to 14) of item COIL SPRING REMOVAL in Section 3D.
6) Remove drive shaft assembly.
To detach snap ring fitted on the spline of differential side joint
(inboard joint) from differential side gear, pull inboard joint by us-
ing a tire lever.
CAUTION:
To prevent breakage of boots (wheel side and differential
side), be careful not to bring them into contact with other
parts when removing drive shaft assembly.
7) Remove drive shaft thrust washer (to vehicle with G16 or J20 en-
gine) from drive shaft and remove drive shaft oil seal as shown
in figure.
CAUTION:
Be careful not to cause damage to drive shaft joint.

YH4
GRAND
VITARA
1. Boot
2. Snap ring
1. Circlip
2 Snap ring plier
3. Cage
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-5
DISASSEMBLY
1) Remove boot band of differential side joint.
2) Slide boot toward the center of shaft and remove snap ring from
outer race, then take shaft out of outer race.
3) Remove circlip and then cage.
4) Remove inside and outside boots from shaft.
CAUTION:

Do not disassemble wheel side joint (outboard joint). If
any malcondition is found in joint, replace it as assem-
bly.

Do not disassemble ball joint of differential side joint.
If any malcondition is found in ball joint, replace differ-
ential side joint assembly.
INSPECTION

Check boots for breakage or deterioration. Replace them as nec-
essary.

Check circlip, snap ring and boot bands for breakage or deforma-
tion. Replace as necessary.
CLEANING

Wash disassembled parts (except boots) in degreaser. After
washing, dry parts completely by blowing air.

Clean boots with cloth. DO NOT wash boots in degreaser, such
as gasoline or kerosene, etc.
Washing in degreaser causes deterioration of boot.

YH4
GRAND
VITARA
1. Boot
2. Boot band
1. Circlip1. Cage Wheel side
ªAº Fill grease 85g (3.0 oz)
4A2-6 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
ASSEMBLY
CAUTION:

To prevent any problem caused by washing solution, do
not wash joint boots. Degreasing of those parts with cloth
is allowed.

For M / T vehicle with H25 engine
To ensure full performance of joint as designed, be sure
to distinguish between two types of grease in repair set
and apply specified volume to respective joint. i.e. yellow
grease to wheel side joint and black one to differential
side.

Bend each boot band against forward rotation.

Do not squeeze or distort boot when fastening it with
bands.
Distorted boot caused by squeezing air may reduce its du-
rability.
1) Fully apply joint grease to wheel side joint.
Use joint grease in the tube included in spare part.
2) Fit wheel side boot on shaft.
Fill up inside of boot with joint grease of about 90 gram.
Before fixing boot band, insert screwdriver into boot on joint side
and allow air to enter boot so that air pressure in boot becomes
the same as atmospheric pressure.
3) Fixing boot band.
4) Install boot onto drive shaft till its small diameter side fits to shaft
groove and fix there with boot band.
5) Install cage to shaft.
CAUTION:
Install cage directing smaller outside diameter side to
shaft end.
6) Install circlip by using snap ring plier.

YH4
GRAND
VITARA
ªAº: Fill grease 90 ± 95 g (3.2 ± 3.4 oz)
1. Circlip
[LH] [RH] Differential side
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-7
7) Apply grease to entire surface of cage.
Use joint grease in tube included in spare part or joint grease
(99000-25120).
8) Insert cage into outer race and fit circlip into groove of outer
race.
CAUTION:
Position opening of circlip ªaº so that it will not be lined
up with a ball.
9) Apply grease to inside of outer race, and fit boot to outer race.
Fill up inside of boot with joint grease.
ªAº: Joint Grease 99000-25120
(about 90 ± 95g / 3.2 ± 3.4 oz)
10) Fitting boot to outer race, adjust so that measurements ªbº and
ªcº become as indicated in figure.
Length ªbº: 203.2 ± 213.2 mm
(8.00 ± 8.40 in.)
196.8 ± 206.8 mm
(7.75 ± 8.14 in.) M
/
T vehicle with . . . . . . . . .
H25 engine
ªcº: 125.5 ± 135.5 mm
(4.94 ± 5.33 in.)
127.5 ± 137.5 mm
(5.02 ± 5.41 in.) M
/
T vehicle with . . . . . . . . .
H25 engine
Before fixing boot band, insert screwdriver into boot on joint
side and allow air to enter boot so that air pressure in boot be-
comes the same as atmospheric pressure.
11) Clamp boot band. Check boots for distortion or dent.

YH4
GRAND
VITARA
1. Drive shaft oil seal
1. Drive shaft flange bolt and nut
2. Front spindle thrust washer
3. Axle shaft drive flange
ªAº
1. Drive shaft joint
2. Oil seal
3. Pipe
4. Thrust washer4
4A2-8 FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL
INSTALLATION
Install drive shaft assembly by reversing removal procedure and
noting following points.

Clean front drive shaft oil seal and then apply lithium grease to oil
seal and DOJ shaft.
ªAº: Grease 99000-25010

Check oil seal for breakage or deterioration.
Replace it as necessary.

Drive in oil seal until its end contacts stepped surface of drive
shaft joint by using a pipe whose inner diameter is 76 mm (2.992
in.) or more and outer diameter is 80 mm (3.150 in.) or less.
Diameter ªaº: 76 mm (2.992 in.) or more
Diameter ªbº: 80 mm (3.150 in.) or less

Drive in drive shaft thrust washer (Vehicle with G16 or J20 en-
gine).

RH Side
Push differential side joint by hand until it is positioned by snap
ring fitted to its spline.
LH Side
Connect drive shaft flange bolts and nuts.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

Apply grease to front spindle thrust washer and front spindle part
of drive shaft.
ªAº: Grease 99000-25010

When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange.
ªBº: Sealant 99000-31090
Tightening Torque
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
CAUTION:

To prevent breakage of boots (wheel side and differen-
tial side), be careful not to bring them into contact with
other parts when installing drive shaft assembly.

Do not pull housing of differential side joint.
If housing is pulled, it may be detached from drive shaft.

Fill specified differential gear oil into differential case to specified
level.

YH4
GRAND
VITARA
1. Left drive shaft
2. Tire lever
1. Shaft bearing1. Axle oil seal
2. Circlip
3. Axle bearing
FRONT DRIVE SHAFT / SHAFT BEARING, OIL SEAL 4A2-9
SHAFT BEARING / OIL SEAL
REMOVAL
1) Remove drive shaft assembly.
Refer to item DRIVE SHAFT REMOVAL (LEFT and RIGHT) in
this section.
For right side shaft bearing / oil seal removal, drain differential
gear oil.
2) Remove left drive shaft by using tire lever.
3) Remove left side strut. Refer to steps 1) and 4) to 8) of item
STRUT DAMPER REMOVAL in Section 3D.
4) Remove oil seal, using plain screw driver.
5) Remove circlip.
6) Remove bearing, using special tools (A) and (B).
Special Tool
(A): 09941-64510
(B): 09930-30102