Ignition SUZUKI GRAND VITARA 2003 2.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2003, Model line: GRAND VITARA, Model: SUZUKI GRAND VITARA 2003 2.GPages: 801, PDF Size: 12.15 MB
Page 527 of 801
YH4
GRAND
VITARA
8-2 BODY ELECTRICAL SYSTEM
GENERAL DESCRIPTION
The body electrical components of this vehicle are designed to operate on 12 Volts power supplied by the battery.
The electrical system utilizes negative ground polarity.
CAUTIONS IN SERVICING
When performing works related to electric systems, observe follow-
ing cautions for the purpose of protection of electrical parts and pre-
vention of a fire from occurrence.
When removing the battery from the vehicle or disconnecting the
cable from the battery terminals for inspection or service works
on the electric systems, always confirm first that the ignition
switch and all the other switches have been turned OFF. Other-
wise, the semi-conductor part may be damaged.
When disconnecting cables from the battery, be sure to discon-
nect the one from the negative (±) terminal first and then the other
from the positive (+) terminal.
Reverse the above order when connecting the cables to the bat-
tery terminals.
When disconnecting connectors, never pull the wiring harnesses.
Unlock the connector lock first and then pull them apart by holding
connectors themselves.
When connecting connectors, also hold connectors and put them
together until they lock securely (a click is heard).
Page 532 of 801
YH4
GRAND
VITARA
8B
LIGHTING SYSTEM 8B-1
SECTION 8B
LIGHTING SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
GENERAL DESCRIPTION8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight with Leveling System (If Equipped) 8B- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearance, Tail and License Plate Lights 8B- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back-up Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Lights8B- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights8B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights with Leveling System (If Equipped) 8B- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn Signal and Hazard Warning Lights 8B- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Fog Light (If Equipped)8B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 539 of 801
YH4
GRAND
VITARA
8B-8 LIGHTING SYSTEM
HEADLIGHTS WITH LEVELING SYSTEM
(IF EQUIPPED)
LEVELING SWITCH
INSPECTION
To check the switch operation, substitute it with a new one. If proper
operation is obtained, it means the switch is defective.
Replace it with a new one.
LEVELING ACTUATOR
INSPECTION
All headlight system couples connected including leveling actuator
and switch, and at Ignition switch ON, listen to the leveling actuator
sound on both actuators according to the movement of the leveling
switch. If no sound is heard with the movement of the leveling
switch, replace headlight assembly.
Page 543 of 801
YH4
GRAND
VITARA
8C
INSTRUMENTATION / DRIVER INFORMATION 8C-1
GENERAL DESCRIPTION8C- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8C- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8C- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8C- 2. . . . . . . . . . . . . . . . .
Abbreviations 8C- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8C- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8C- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8C- 2. . . . . . . . . . . . . . . .
Combination Meter 8C- 2. . . . . . . . . . . . . . . . . . .
DIAGNOSIS8C- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 4. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 4. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C- 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C- 4. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light Remainder Warning Buzzer 8C- 5. . . . . . . Seat Belt Warning Light (If Equipped) 8C- 5. . .
Ignition Key Remainder Warning
Buzzer (If Equipped) 8C- 5. . . . . . . . . . . . . . . . .
Cigarette Lighter and Accessory Socket 8C- 5.
ON-VEHICLE SERVICE8C- 6 . . . . . . . . . . . . . . . .
Ignition (Main) Switch 8C- 6. . . . . . . . . . . . . . . . .
Combination Meter 8C- 7. . . . . . . . . . . . . . . . . . .
Speedometer and VSS 8C- 8. . . . . . . . . . . . . . . .
Fuel Meter / Fuel Gauge Unit 8C- 9. . . . . . . . . . . .
Engine Coolant Temp. (ECT) Meter and
Sensor 8C-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pressure Light 8C-11. . . . . . . . . . . . . . . . . . . .
Brake and Parking Brake Warning
Light 8C-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Key Remainder (If Equipped) /
Light Remainder Warning Buzzer 8C-12. . . . . .
Door Switch 8C-13. . . . . . . . . . . . . . . . . . . . . . . . .
Seat Belt Warning Light (If Equipped) 8C-13. . .
SECTION 8C
INSTRUMENTATION/DRIVER INFORMATION
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System
Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.
Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS
Page 545 of 801
YH4
GRAND
VITARA
1. To door switch (driver side) B / Bl
2. To transmission range switch G / Bl
(A / T vehicle only, if equipped) L
3. To transmission range switch G / O
(A / T vehicle only, if equipped) 2
4. To transmission range switch Y / G
(A / T vehicle only, if equipped) D
5. To transmission range switch O / Bl
(A / T vehicle only, if equipped) N
6. To transmission range switch O / G
(A / T vehicle only, if equipped) P
7. To transmission range switch R
(A / T vehicle only, if equipped) R
8. To ground B
9. To PCM (A / T vehicle only) W / B
10. To ECT sensor Y / W
11. To fuel level gauge Bl / W
12. To ground B / Y
13. To combination switch G / Y
NOTE:
Terminal arrangement of coupler viewed from harness side.
Coupler A Coupler B Coupler C
Coupler A Coupler B Coupler C
1. Blank ÐÐ
2. Blank ÐÐ
3. To ignition switch B / W
4. Blank ÐÐ
5. To ABS control module Bl / O
(if equipped)
6. To PCM (A / T vehicle only) Gr / Bl
7. To ABS control module Br
(if equipped)
8. To VSS Bl / Y
9. To combination switch G / R
10. To SDM (if equipped) Y / G or Bl
11. To main fuse W / Bl
12. To fuse box W
13. To combination switch R
14. To ECM (PCM for A / T vehicle) V
(if equipped)
15. To ECM (PCM for A / T vehicle) V / Y
16. To ECM (PCM for A / T vehicle) O / B
(if equipped)1. To ground B
2. To ECM (PCM for A / T vehicle) Br
3. To ignition switch (if equipped) V / R
4. To brake fluid level switch R / B
5. To parking brake switch V
6. To seat belt switch (if equipped) Gr / R
7. To generator W / R
8. To oil pressure switch Y / B
9. To combination switch R / Y
10. To ignition switch (if equipped) Bl / R or CHECK
or ENGINE
or ABSif equipped
if equippedif equipped
INSTRUMENTATION / DRIVER INFORMATION 8C-3
Page 547 of 801
YH4
GRAND
VITARA
INSTRUMENTATION / DRIVER INFORMATION 8C-5
BRAKE AND PARKING BRAKE WARNING LIGHT
TroublePossible CauseCorrection
Brake warning light does
not light upBulb in combination meter blown
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)
Printed plate in combination meter
faulty
Parking brake switch faulty
Brake fluid level switch faulty
Wiring or grounding faultyReplace bulb
Replace fuse to check for short
Replace printed plate
Replace parking brake switch
Replace brake fluid level switch
Repair
LIGHT REMAINDER WARNING BUZZER
TroublePossible CauseCorrection
Light remainder warning
buzzer shows no
soundingªTAILº fuse blown
Buzzer faulty
Wiring or grounding faulty
Driver side door switch faultyReplace fuse to check for short
Replace buzzer
Repair
Replace door switch
SEAT BELT WARNING LIGHT (IF EQUIPPED)
TroublePossible CauseCorrection
Seat belt warning light
does not light upBulb in combination meter blown
ªIG / METERº fuse blown (Hard Top
Model)
ªIGº fuse blown (Canvas Top Model)
Seat belt switch faulty
Wiring or grounding faultyReplace bulb
Replace fuse to check for short
Replace seat belt switch
Repair
IGNITION KEY REMAINDER WARNING BUZZER (IF EQUIPPED)
TroublePossible CauseCorrection
Ignition key remainder
warning buzzer shows no
soundingªDOMEº fuse blown (Hard Top Model)
ªDOMº fuse blown (Canvas Top
Model)
Buzzer faulty
Wiring or grounding faulty
Driver side door switch faulty
Ignition key switch faultyReplace fuse to check for short
Replace buzzer
Repair
Replace door switch
Replace ignition key switch
CIGARETTE LIGHTER AND ACCESSORY SOCKET
TroublePossible CauseCorrection
Cigarette lighter /
accessory socket shows
no operationªCIGARº fuse blown (Hard Top Model)
ªCIGº fuse blown (Canvas Top Model)
Ignition switch faulty
Cigarette lighter / accessory socket
faulty
Wiring or grounding faultyReplace fuse to check for short
Replace ignition switch
Replace cigarette lighter / accessory
socket
Repair
Page 548 of 801
YH4
GRAND
VITARA
8C-6 INSTRUMENTATION / DRIVER INFORMATION
KeyPosition
TerminalWire
color
Hard Top Model
Canvas Top Model
ON-VEHICLE SERVICE
IGNITION (MAIN) SWITCH
INSPECTION
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Disconnect main switch lead wire coupler.
4) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace ignition
(main) switch.
+B+ACCIG1-1IG1-2IG2STL1L2K1K2
W/YBlB/WB/WY/BB/YBBGG
OUTLOCKLOCK
ACC
IN
ON
START
REMOVAL
1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYSTEM
in Section 10B of this manual.
3) Remove steering column referring to Section 3C1 of this manu-
al. Then remove steering lock / ignition (main) switch from steer-
ing column.
INSTALLATION
1) Install steering lock / ignition (main) switch to steering column.
Install steering column assembly referring to Section 3C1 of this
manual.
2) Enable air bag system. Refer to ENABLING AIR BAG SYSTEM
in Section 10B of this manual.
NOTE:
When installing steering column, special care must be tak-
en for tightening sequence and its torque.
Page 551 of 801
YH4
GRAND
VITARA
INSTRUMENTATION / DRIVER INFORMATION 8C-9
1. Exhaust pipe
FUEL METER / FUEL GAUGE UNIT
FUEL METER
INSPECTION
1) Remove rear bumper facing.
2) Detach grommet (3) from vehicle.
3) Disconnect coupler (2) of fuel pump and gauge.
4) Turning switch ON, and check that fuel meter indicates E.
5) Turn ignition switch OFF.
6) Ground Bl / W lead through a 3.4 W test bulb (4) as illustrated.
7) Turn ignition switch ON and check that bulb light up and pointer
(5) moves to F side.
8) If fuel meter shows no operation, repair or replace defective
parts.
FUEL SENDER GAUGE
INSPECTION
1) Remove fuel pump assembly (1) referring to FUEL PUMP RE-
MOVAL in Section 6C.
2) Check resistance between terminals (A) and (B) under each
float position.
Float Position
FuelResistance ()56 model66 modelMeterResistance ()
ªaº88.3 mm
(3.48 in.)51.7 mm
(2.04 in.)F6 ± 8
ªbº157.2 mm
(6.20 in.)139.6 mm
(5.50 in.)1/229.5 ± 35.5
ªcº254.9 mm
(10.0 in.)254.9 mm
(10.0 in.)E94 ± 96
If measured valve is out of specification, replace fuel sender gauge.
Page 552 of 801
YH4
GRAND
VITARA
8C-10 INSTRUMENTATION / DRIVER INFORMATION
G16
J20
H25
1. ECT sensor
1
ENGINE COOLANT TEMP. (ECT) METER AND
SENSOR
ENGINE COOLANT TEMPERATURE (ECT) METER
INSPECTION
1) Disconnect Y/W lead wire going to ECT sensor.
2) Turn ignition switch ON, and check that ECT meter indicates
COOL.
3) Turn ignition switch OFF.
4) Ground Y/W lead wire through a 3.4 W test bulb (1) as illustrated.
5) Turn ignition switch ON, and check that bulb light up and pointer
(2) moves to hot side.
6) If ECT meter shows no operation, repair or replace defective
parts.
ENGINE COOLANT TEMPERATURE (ECT) SENSOR
REMOVAL AND INSTALLATION
Refer to ECT SENSOR in ON-VEHICLE SERVICE in Section 6E1
(for G16 and J20) or Section 6E2 (for H25) of this manual for details.
Page 554 of 801
YH4
GRAND
VITARA
8C-12 INSTRUMENTATION / DRIVER INFORMATION
BRAKE AND PARKING BRAKE WARNING
LIGHT
BRAKE FLUID LEVEL SWITCH
INSPECTION
Check switch (1) for continuity.
If check result is not as specified, replace switch (reservoir).
OFF position (float up)
No continuity
ON position (float down)Continuity
PARKING BRAKE SWITCH
INSPECTION
Check switch (1) for continuity.
If check result is not as specified, replace switch.
OFF position
(parking brake lever released)
No continuity
ON position
(parking brake lever pulled up)Continuity
IGNITION KEY REMAINDER (IF EQUIPPED) /
LIGHT REMAINDER WARNING BUZZER
REMOVAL
1) Remove combination meter (1). Refer to COMBINATION ME-
TER in this section.
2) Remove buzzer unit (2) from combination meter.
INSTALLATION
Reverse removal procedure for installation.