turn signal TOYOTA AVENSIS 2005 Service User Guide

± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±305
AVENSIS REPAIR MANUAL (RM1018E)Hand±held Tester DisplayDiagnostic Note Normal Condition *
1Measurement Item/Range
(Display)
ELECT LOAD SIGElectrical load signal/
ON or OFF
Tail light switch ON: ON

Defogger switch ON: ON

STOP LIGHT SWStop light switch/
ON or OFF
Brake pedal depressed: ON

Brake pedal released: OFF

PS OIL PRESS SWPower steering signal/
ON or OFF

While turning the steering wheel:
ON

While not turning the steering
wheel: OFF
The idle±up control is performed
when PS is ON.
PS SIGNALPower steering signal/
ON or OFFWhen the steering wheel is turned:
ONThis signal is usually ON status
until the IG switch is turned OFF.
SCV VSVVSV status for intake air control
valve/ ON or OFFVSV operation: ON

FUEL PUMP / SPDFuel pump/speed status/
ON/H or OFF/M,LIdling: ON

EVAP VSVVSV status for EVAP control/
ON or OFFVSV operating: ONVSV for EVAP is controlled by the
ECM (ground side duty control)
VVT CTRL B1VVT control status (bank 1)/
ON or OFFVVT system operation: ON

IGNITIONIgnition counter/ Min.: 0, Max.: 4000 to 400

CYL #1, #2, #3, #4Misfire ratio of the cylinder 1 to 4/
Min.: 0 %, Max.: 50 %0 %This item is displayed in only idling
MISFIRE RPMEngine RPM for first misfire range/
Min.: 0 rpm, Max.: 6,375 rpmMisfire 0: 0 rpm

FC TAUFuel Cut TAU: Fuel cut during very
light load/ ON or OFFFuel cut operating: ON
The fuel cut is being performed un-
der very light load to prevent the
engine combustion from becoming
incomplete.
CHECK MODECheck mode/ ON or OFFCheck mode ON: ONSee step 3
O2 RL B1 S2
Oxygen sensor rich lean bank 1
sensor 2:
Response time for oxygen sensor
output to switch from rich to lean/
Min.: 0 ms, Max.: 16,702.5 ms
Idling after warming up:
O2 RL B2 S2
Oxygen sensor rich lean bank 2
sensor 2:
Response time for oxygen sensor
output to switch from rich to lean/
Min.: 0 ms, Max.: 16,702.5 ms
Idling after warming u:
0 to 1,000 msec.

MIL ON RUN DIST
Distance since activation of check
engine warning light/
Min.: 0 km, Max.: 65,535 km
When there is no DTC: 0 km

FUEL PRESS
Fuel high pressure inside fuel de-
livery pipe/
Min.: 0 MPa, Max.: 819 MPa
Idling: 8 to 13 MPa

Running without load (3,000
rpm): 9.5 to 10.5 MPa


*1: If no conditions are specifically stated for ºldlingº, it means the shift lever is at the N or P position, the A/C
switch is OFF and all accessory switches are OFF.
*
2: For A/T only

±
DIAGNOSTICS SFI SYSTEM(1AZ±FE)
05±279
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION PROCEDURE
HINT:
This chart is on the premise that the engine is cranked normally. If the engine is not cranked, proceed to the
problem symptoms table on page 05±168.
When using hand±held tester:
1READ VALUE OF HAND±HELD TESTER(STA SIGNAL)
(a)Connect the hand±held tester to the DLC3.
(b)Turn the ignition switch ON and push the hand±held tester main switch \
ON.
(c)Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALL / STARTER SIGº and read its value dis-
played on the hand±held tester.
Result:
Ignition Switch PositionONSTART
STA SignalOFFON
OKPROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
(See page 05±149)
NG

05±358
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)DTC No.
DTC Detection Condition
Condition (a) of DTC P0120, P0122, P0123, P0220, P0222 or P0223 continues
for 2 sec.
(Open or short in throttle position sensor circuit)Trouble Area
P0120
Detection conditions for DTCs P0122 and P0123 are not satis-
fied but condition (a) is satisfied
(a) VTA1
0.2 V or VTA1  4.8 V
Throttle position sensor (built in throttle body)

ECM
P0122(a) VTA1
0.2 V

Throttle position sensor (built in throttle body)

VTA1 circuit short

VC circuit open

ECM
P0123(a) VTA1  4.8 V

Throttle position sensor (built in throttle body)

VTA1 circuit open

E2 circuit open

VC and VTA1 circuit are short±circuited

ECM
P0220
Detection conditions for DTCs P0222 and P0223 are not satis-
fied but condition (a) is satisfied
(a) VTA2
0.5 V or VTA2  4.97 V and
0.2 V
VTA1
1.8 V

Throttle position sensor (built in throttle body)

ECM
P0222(a) VTA2
0.5 V

Throttle position sensor (built in throttle body)

VTA2 circuit short

VC circuit open

ECM
P0223(a) VTA2  4.97 V and 0.2 V
VTA1
1.8 V

Throttle position sensor (built in throttle body)

VTA2 circuit open

E2 circuit open

VC and VTA2 circuit are short±circuited

ECM
P2135
Condition (a) continues for 0.5 sec. or more, or
condition (b) continues for 0.4 sec. or more:
(a) |VTA1 ± VTA2|
0.02 V
(b) VTA1
0.2 V and VTA2
0.5 V
VTA1 and VTA2 circuit are short±circuited

Throttle position sensor (built in throttle body)

ECM
NOTICE:
When a malfunction is detected, the throttle valve is locked at a certain opening angle. Also, the
whole electronically controlled throttle operation is cancelled until the system returns to normal and
the ignition switch is turned OFF.
HINT:

After confirming DTCs, use the hand±held tester to confirm the throttle valve opening percentage and
closed throttle position switch condition.

The THROTTLE POS means VTA1 signal as well as the THROTTLE POS #2 for the VTA2 signal.
Reference (Normal condition):
Tester displayAccelerator pedal fully releasedAccelerator pedal fully depressed
THROTTLE POS10 to 24 %64 to 96 %
THROTTLE POS #22.1 to 3.1 V4.5 to 5.5 V

05±472
±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, it is useful for determi\
ning whether the vehicle was running
or stopped, the engine was warmed up or not, the air±fuel ratio was lea\
n or rich, etc. at the time of the mal-
function.
1READ VALUE OF HAND±HELD TESTER(STARTER SIGNAL)
(a)Connect the hand±held tester to the DLC3.
(b)Turn the ignition switch ON and push the hand±held tester main switch \
ON.
(c)Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALL / STARTER SIGº and read its value dis- played on the hand±held tester.
Result:
Ignition Switch PositionONSTART
STA SignalOFFON
OKCHECK AND REPLACE ECM (See page 01±32)
NG
2INSPECT PARK/NEUTRAL POSITION SWITCH ASSY
(a)Inspect the park/neutral position switch (A/T) (See page 05±938). NGREPLACE PARK/NEUTRAL POSITION SWITCHASSY (See page 40±8) (GO TO NEXT STEP 3 AF-
TER THE REPLACEMENT)
OK
3READ VALUE OF HAND±HELD TESTER(STARTER SIGNAL)
(a)Connect the hand±held tester to the DLC3.
(b)Turn the ignition switch ON and push the hand±held tester main switch \
ON.
(c)Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALL / STARTER SIGº and read its value dis- played on the hand±held tester.
Result:
Ignition Switch PositionONSTART
STA SignalOFFON
OKSYSTEM OK
NG
4INSPECT IGNITION OR STARTER SWITCH ASSY (See page 80±2)
NG REPLACE IGNITION OR STARTER SWITCH ASSY (GO TO NEXT STEP 5 AFTER THE RE-
PLACEMENT)
OK

± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±473
AVENSIS REPAIR MANUAL (RM1018E)
5 READ VALUE OF HAND±HELD TESTER(STARTER SIGNAL)
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALL / STARTER SIGº and read its value dis-
played on the hand±held tester.
Result:
Ignition Switch PositionONSTART
STA SignalOFFON
OK SYSTEM OK
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR

±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
05±463
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using
\b\b
\b 
\f
reeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, it is useful for determi\
ning whether the vehicle was running
or stopped, the engine was warmed up or not, the air±fuel ratio was lea\
n or rich, etc. at the time of the mal-
function.
1CHECK OTHER DTC OUTPUT(IN ADDITION TO P0556)
(a)Read the DTC using the hand±held tester. Result :
DisplayProceed to
Only ºP0556º is output.A
ºP0556º and other DTCs are output.B
HINT:
If any other codes besides ºP0556º are output, perform the troublesh\
ooting for those DTCs first.
BGO TO RELEVANT DTC CHART(See page 05±309)
A
2 READ VALUE OF HAND±HELD TESTER(INTAKE MANIFOLD ABSOLUTE PRESSURE)
(a) Connect the hand±held tester to the DLC3.
(b) Warm up the engine.
(c) Push the hand±held tester main switch ON.
(d) Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALL / MAPº and read its value displayed on
the hand±held tester with the shift lever is the ºNº position.
Standard :
ConditionIntake Manifold Absolute Pressure
Ignition switch ON (do not start engine)70 to 110 kPa (525 to 825 mmHg, 20.7 to 32.5 in.Hg)
Running without load (2,500 rpm)20 to 35 kPa (150 to 263 mmHg, 5.9 to 10.4 in.Hg)
NG Go to step 7
OK
3 READ VALUE OF HAND±HELD TESTER(STOP LIGHT SWITCH)
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch \
ON.
(c) Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST / ALL / STOP LIGHT SWº and read its value displayed on the hand±held tester.
Result :
Brake PedalSTP Signal
DepressedON
ReleasedOFF

A81707
Free Pushed in
43 21
A72880
Brake Pedal
DepressedBrake Pedal
Released
ST1± (+)
E11
E1 (±)
E10
ECM Connector
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±457
AVENSIS REPAIR MANUAL (RM1018E)
1 CHECK OPERATION OF STOP LIGHT
(a) Check if the stop lights go on and off normally when the brake pedal is depressed and released.
NG REPAIR OR REPLACE STOP LAMP SWITCH
CIRCUIT
OK
2 INSPECT STOP LIGHT SWITCH ASSY
(a) Check for continuity between each pair of the terminals.
Standard:
Switch positionTerminal No.Specified condition
Switchpin free1 ± 2ContinuitySwitch pin free3 ± 4No continuity
Switchpinpushed in1 ± 2No continuitySwitch pin pushed in3 ± 4Continuity
NG REPLACE STOP LIGHT SWITCH ASSY
OK
3 READ VALUE OF HAND±HELD TESTER(STP SIGNAL AND ST1± VOLTAGE)
(a) Turn the ignition switch ON.
(b) Select the item ºDIAGNOSIS / OBD/MOBD / DATA LIST
/ ALL / STOP LIGHT SWº and read its value displayed on
the hand±held tester.
Standard:
Brake PedalSpecified condition
DepressedSTP Signal ON
ReleasedSTP Signal OFF
(c) Measure the voltage between the specified terminals of
the E10 and E11 ECM connectors.
Standard:
Symbols (Terminal No.)Brake pedalSpecified condition
ST1± (E10±12) DepressedBelow 1.5 VST1 (E10 12)
± E1 (E11±1)
Released7.5 to 14 V
NG Go to step 4
OK
CHECK FOR INTERMITTENT PROBLEMS

A76880
FL MAIN
StarterCircuit
Opening Relay
Park/Neutral
Position SWIG2 Relay
AM2
BatteryECM
STA IGSW IGN Ignition SWFuel Pump
ST2IG2
ST
Relay
(NE Signal) (A/T)FC
IG2STTr
(M/T)
(A/T) AM2
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
05±507
AVENSIS REPAIR MANUAL (RM1018E)
FUEL PUMP CONTROL CIRCUIT
CIRCUIT DESCRIPTION
In the diagram below, when the engine is cranked, current flows from terminal ST2 of the ignition switch to
the starter relay coil and also current flows to terminal STA of ECM (STA signal).
When the STA signal and NE signal are input to the ECM, Tr is turned ON, current flows to the coil of the
circuit opening relay, the relay switches on, power is supplied to the fuel pump and the fuel pump operates.
While the NE signal is generated (engine running), the ECM keeps Tr ON (circuit opening relay ON) and the
fuel pump also keeps operating.
05CK1±01

A76879
IP1I13
Ignition Switch
IGN Driver Side J/B
E9
E11ECM
Battery FL MAINEFI
No. 1
2
B±G2
118
9
18 4DH
2
E9E9
1 12 31 5
EFI
Relay
D
EFBR GR B±W
DA
J/C 1A
J28IGSW
+B2 MREL
E1
Engine Room
J/B No. 41 4A
4BEngine Room
R/B No. 1 and
Engine Room
J/B No. 1 1EFI AM2
1 211
1 2
B±G6
(RHD) IE4 1 (LHD)
B±R B±R B±R
4 4
4
4
4
4Engine Room
R/B No. 4
Engine
Room
R/B No. 4B±Y
B±W
B±R
ECW±B
B±RB±R B±R
(RHD) (LHD)
D J14 D J28 (RHD)(LHD)
D J14
D J28 D J141
E9 +B (RHD)
(LHD)B±W
B±W (RHD)
(LHD)B±W
J26A
J27E
J8
J/CJ/C
CC
IE12
GR
(LHD) (RHD)IP1 IE42
3
AM2 IG2
05±502
± DIAGNOSTICSSFI SYSTEM (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
ECM POWER SOURCE CIRCUIT
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, battery positive voltage is applied to terminal IGSW of the ECM and
the EFI relay (Marking: EFI) control circuit in the ECM sends a signal to terminal MREL of the ECM switching
on the EFI relay.
This signal causes current to flow to the coil, closing the contacts of the EFI relay and supplying power to
terminals +B and +B2 of the ECM.
If the ignition switch is turned off, the ECM continues to switch on the EFI relay for maximum 2 seconds for
the initial setting of the throttle valve.
WIRING DIAGRAM
05CK0±01


B12608
A76903
E12
ECM Connector
FP+
FP± E1
E11
A14558
Normal Signal Waveforms
5 msec./Division 10 V/
Division
GND FP±
FP+
05±478
±
DIAGNOSTICS SFI SYSTEM(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
1CHECK OPERATION OF FUEL PUMP(HIGH PRESSURE)
(a)With the engine running or cranking, use a sound scope to check that there is the normal operating sounds of the
fuel pump (high±pressure) when it is operated.
Standard:
There is the operating sounds of the fuel pump (high±
pressure).
NGREPLACE FUEL PUMP (HIGH PRESSURE)
OK
2INSPECT ECM(FP+ AND FP± VOLTAGE)
(a)Turn the ignition switch ON, and check the waveforms be- tween terminals FP+ and E1, and FP± and E1 of the E11
and E12 ECM connectors.
HINT:
The correct waveform is as shown in the illustration.
NGCHECK AND REPLACE ECM (See page 01±32)
OK
3CHECK FUEL PUMP(HIGH PRESSURE) (See page 11±33)
NG REPLACE FUEL PUMP(HIGH PRESSURE)
OK