heater TOYOTA CAMRY 1996 Owners Manual

60
To turn the rear wipers and washers on,
twist the knob at the end of the lever.
The key must be in the ONº position.
The wipers will operate at intervals when
the knob is in the INTº position.
The washer squirts at the two marked
knob positions. The knob will automatical-
ly return from these positions when it is re-
leased.
If the washer does not work, check to see
whether the washer tank is empty. For in-
formation on adding washer fluid, see
Adding washer fluidº in Chapter 7-3.
NOTICE
Do not operate the rear wipers if the
rear window is dry. It may scratch
the glass.
To defog or defrost the rear window,
push the switch.
The key must be in the ONº position.
The thin heater wires on the inside of the
rear window will quickly clear the sur-
faces. An indicator light will illuminate to
indicate the defogger is operating.
Push the switch once again to turn the de-
fogger off.
The system will automatically shut off af-
ter the defogger has operated about 15
minutes.
Rear window wipers and
washer (wagon) Rear window defogger
ProCarManuals.com

61 Make sure you turn the defogger off when
the window is clear. Leaving the defogger
on for a long time could cause the battery
to discharge, especially during stop-and-
go driving. The defogger is not designed
for drying rain water or for melting snow.
NOTICE
When cleaning the inside of the rear
window, be careful not to scratch or
damage the heater wires.
ProCarManuals.com

Part 1Car audio system operating tips
77
OPERATION OF
INSTRUMENTS
AND CONTROLSÐ
Chapter 1-7
Car audio system and
Air conditioning
system
Car audio system operating tips
AM-FM radio with electronic
tuner
AM-FM radio with electronic
tuner and cassette tape player
AM-FM radio with electronic
tuner, cassette tape player and
Compact Disc player
Air conditioning controls
Heater controls
Side vents
Lower vent
You can listen to the car audio system
when the ignition key is at ONº or
ACCº. However, if the engine is not
running, the key must be in the ACCº
position.
ILLUMINATION CONTROL LOGIC
On some audio-units, when the instru-
ment panel lights are on, the letters on op-
erable buttons of the mode in current use
light up together with the mode selection
and eject buttons.
RADIO
FM reception tips
Most of us are not aware that a vehicle is
not an ideal place to listen to a radio. Be-
cause it moves, reception conditions
change continuously. Buildings, terrain,
signal distance and noise from other ve-
hicles are all working against good recep-
tion. Some FM reception conditions may
appear to be problems even though they
are normal.
The following characteristics are normal
for a given reception area, and they do not
indicate any problem with the radio itself.Fading and drifting: On the average,
the broadcast range of FM stations is
limited to about 40 km (25 miles), ex-
cept for some high power stations.
If a vehicle is moving away from the
desired station's transmitter, the signal
will tend to fade and/or drift. This phe-
nomenon is more noticeable with FM
than with AM, and is accompanied by
distortion.
Fading and drifting can be minimized
to a certain degree by fine tuning, or
you should tune in to a stronger signal.
Static and Fluttering: When the line-
of-sight path between a transmitter
and vehicle is blocked by large build-
ings or the like, static or fluttering may
occur because of the characteristic of
FM. In a similar effect, a fluttering
noise is sometimes heard when driv-
ing along a tree-lined road.
This static and fluttering can be re-
duced by adjusting the tone control for
greater bass response until the distur-
bance has passed.
ProCarManuals.com

11 0For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
(d) Ventilation
1. Turn the temperature control knob at
the LOW position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Turn the air flow control knob to the
FACE position.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(e) Windshield defogging and defrost-
ing
To remove interior fog on the windshield:
1. Turn the temperature control knob to
any position.
2. Move the air intake control lever to the
OUTSIDE AIR position.3. Turn the air flow control knob to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
To remove frost or exterior fog on the
windshield:
1. Turn the temperature control knob to
the HIGH position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Turn the air flow control knob to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob to the
HIº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(f) Air flow selection
FACE positionÐThis position directs the
air flow to face level.BI-LEVEL positionÐThis position directs
the air flow to face level and the floor. Ex-
cept in ventilation, the air to the floor is
slightly warmer than that to face level.
FLOOR positionÐThis position directs air
flow mostly to the floor.
FLOOR/WINDSHIELD position Ð This
position directs the air flow to the wind-
shield as well as the floor.
WINDSHIELD positionÐThis position di-
rects air flow mostly to the windshield and
front side windows.
Do not use the WINDSHIELD position
during cooling operation in extremely hu-
mid weather. The difference between the
temperature of the outside air and that of
the windshield could cause the outer sur-
face of the windshield to fog up, blocking
your vision.
(g) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory,
check the dashboard vents. (See
Side ventsº or Lower ventº after
Heater controlsº.)ProCarManuals.com

11 5 For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Press in any fan speed control button
except the OFFº button.
5. Press in the air conditioning on-off but-
ton.
(d) Ventilation
1. Turn the temperature control knob at
the LOW position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.
3. Press in the FACE button of the air flow
control buttons.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(e) Windshield defogging and defrost-
ing
To remove interior fog on the windshield:
1. Turn the temperature control knob to
any position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.3. Press in the WINDSHIELD button of
the air flow control buttons.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
To remove frost or exterior fog on the
windshield:
1. Turn the temperature control knob to
the HIGH position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.
3. Press in the WINDSHIELD button of
the air flow control buttons.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob to the
HIº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(f) Air flow selection
FACE buttonÐThis button directs the air
flow to face level.
BI-LEVEL buttonÐThis button directs
the air flow to face level and the floor. Ex-
cept in ventilation, the air to the floor is
slightly warmer than that to face level.FLOOR buttonÐThis button directs air
flow mostly to the floor.
FLOOR/WINDSHIELD buttonÐThis but-
ton directs air flow to the windshield as well
as the floor.
WINDSHIELD buttonÐThis button di-
rects air flow mostly to the windshield and
front side windows.
Do not use the WINDSHIELD button dur-
ing cooling operation in extremely humid
weather. The difference between the tem-
perature of the outside air and that of the
windshield could cause the outer surface
of the windshield to fog up, blocking your
vision.
(g) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory,
check the dashboard vents. (See
Side ventsº or Lower ventº after
Heater controlsº.)

To help cool down the interior after
parking in the hot sun, drive for the first
few minutes with the windows open.
After the excess heat has blown away,
close the windows.ProCarManuals.com

11 7
Heater controls
ProCarManuals.com

11 9 (a) Controls and functions
The temperature control knob is used to
turn on and off the heater and adjust the
temperature of the heated air.
Turn the knob toward the FULL HEATING
position for higher temperature. Turning
the knob to the NO HEAT position turns off
the heater.
The air intake control lever is used to se-
lect intake air, either outside air or recircu-
lated air.
With the lever in the OUTSIDE AIR posi-
tion, the system will take fresh outside air
into the unit. For recirculated air, move the
lever to the RECIRCULATED AIR position.
The air flow control knob is used to select
the air flow outlets air is delivered from.
See (e) Air flow selectionº for detailed in-
formation.
The fan speed control knob is used to turn
on and off the fan and select the fan
speed.
The higher the fan speed setting is, the
more air is delivered. Turning the knob to
the OFFº position turns off the fan.(b) Heating
1. Turn the temperature control knob
anywhere except the NO HEAT position.
If cooler air is desired at face level for bi-
level operation, turn the knob around the
middle.
2. Move the air intake control lever to the
OUTSIDE AIR position.
If quick circulation of heated air is desired,
move the lever to the RECIRCULATED
AIR position.
For normal use, it is best to keep the lever
in the OUTSIDE AIR position. Otherwise
the windows will fog up more easily.
3. Turn the air flow control knob to the
FLOOR position.
If cooler air is desired at face level for bi-
level operation, turn the knob to the BI-
LEVEL position.
If the windshield fogs up easily, turn knob
to the FLOOR/WINDSHIELD position.
For detailed information on air flow control
including other settings, see (e) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.(c) Ventilation
1. Turn the temperature control knob to
the NO HEAT position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Move the air flow control knob to the
FACE position.
For detailed information on air flow control
including other settings, see (e) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
(d) Windshield defogging and defrost-
ing
1. Turn the temperature control knob at
the FULL HEATING position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Turn the air flow control knob to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (e) Air flow selectionº.
4. Turn the fan speed control knob to the
HIº position.
(e) Air flow selection
FACE positionÐThis position directs the
air flow to face level.ProCarManuals.com

170Begin by vacuuming thoroughly to re-
move as much dirt as possible. Several
types of foam cleaners are available;
some are in aerosol cans and others are
powders or liquids which you mix with wa-
ter to produce a foam. To shampoo the
carpets, use a sponge or brush to apply
the foam. Rub in overlapping circles.
Do not apply waterÐthe best results are
obtained by keeping the carpet as dry as
possible. Read the shampoo instructions
and follow them closely.
Seat belts
The seat belts may be cleaned with
mild soap and water or with lukewarm
water.
Use a cloth or sponge. As you are clean-
ing, check the belts for excessive wear,
fraying, or cuts.
Do not use dye or bleach on the
beltsÐit may weaken them.
NOTICE
Windows
The windows may be cleaned with any
household window cleaner.
When cleaning the inside of the
windows, be careful not to scratch
or damage the heater wires on the
rear window.
NOTICE
Air conditioning control panel, car au-
dio, instrument panel, console panel,
and switches
Use a soft damp cloth for cleaning.
Soak a clean soft cloth in water or luke-
warm water then lightly wipe off any dirt.
NOTICE
Do not use organic substances (sol-
vents, kerosene, alcohol, gasoline,
etc.) or alkaline or acidic solutions.
These chemicals can cause discolor-
ing, staining or peeling of the sur-
face.
If you use cleaners or polishing
agents, make sure their ingredients
do not include the substances men-
tioned above.
If you use a liquid car freshener, do
not spill the liquid onto the vehicle's
interior surfaces. It may contain the
ingredients mentioned above. Im-
mediately clean any spill using the
method mentioned above.
Leather Interior
The leather upholstery may be cleaned
with neutral detergent for wool.
Remove dirt using a soft cloth dampened
with 5% solution of neutral detergent for
wool. Then thoroughly wipe off all traces of
detergent with a clean damp cloth.
After cleaning or whenever any part of the
leather gets wet, dry with a soft clean cloth.
Allow the leather to dry in a ventilated
shaded area.
NOTICE
If a stain should fail to come out with
a neutral detergent, apply a cleaner
that does not contain an organic
solvent.
Never use organic substances such
as benzine, alcohol or gasoline, or
alkaline or acid solutions for clean -
ing the leather as these could cause
discoloring.
Use of a nylon brush or synthetic fi -
ber cloth, etc. may scratch the fine
grained surface of the leather.
Mildew may develop on soiled leath -
er upholstery. Be especially careful
to avoid oil spots. Try to keep your
upholstery always clean.
Long exposure to direct sunlight
may cause the leather surface to
harden and shrink. Keep your ve-
hicle in a shaded area, especially in
the summer.
The interior of your vehicle is apt to
heat up on hot summer days, so
avoid placing on the upholstery
items made of vinyl or plastic or
containing wax as these tend to
stick to leather when warm.
Improper cleaning of the leather up -
holstery could result in discolor-
ation or staining.
If you have any questions about the
cleaning of your Toyota, your local To-
yota dealer will be pleased to answer
them.
ProCarManuals.com

217
21. WIPER 20 A: Windshield wipers and
washer, rear window wipers and washer,
air bag system
22. TURN 7.5 A: Turn signal lights
23. IGN 7.5 A: Multiport fuel injection sys-
tem/sequential multiport fuel injection
system, charging system, air bag system
24. CIG/RADIO 15 A: Audio system,
daytime running light system, clock, ciga-
rette lighter, air bag system, shift lock sys-
tem
25. MIR. HTR 10 A: Outside rear view
mirror heater26. TAIL 15 A: Tail lights, parking lights,
license plate lights, instrument panel
lights, rear light failure warning system
27. SRS 7.5 A: SRS airbag system
28. A/C 10 A: Air conditioning control
system
29. HEAD (LWR-RH) 15 A: Right-hand
headlight (low beam)
30. HEAD (LWR-LH) 15 A: Left-hand
headlight (low beam)
31. DRL 5 A: Daytime running light sys-
tem
32. ST 10 A: Starting systemFuses (type C)
33. AM1 40 A: Starting system
34. P/W 30 A: Electric moon roof, power
windows, tilt steering, power door lock
controls, power back door lock control,
power seat
35. DEFOG 40 A: Rear window defogger
36. HTR 40 A: Air conditioning control
system
37. MAIN NO. 1 40 A: Starting system
38. CDS 30 A: Electric cooling fan
39. RDI 30 A: Electric cooling fan
ProCarManuals.com