change time TOYOTA CAMRY 1999 Service Workshop Manual

Toyota Supports ASE CertificationPage 1 of 2
BO019±99
Title:
DOOR MIRROR WIND NOISE
Models:
'97 ± '99 Camry
Technical Service
BULLETIN
December 3, 1999

Wind/road noise heard around the door mirrors of some Japan produced Camry vehicles
may be caused by an improperly positioned mirror wire harness grommet and/or harness
connector.
1997 through 1999 Camry vehicles. (Japan produced only)
PLANTSTARTING VIN
TMC
JT2BG22K * X0367325
JT2BG28K * X0367352
TMCJT2BG28K X0367352
JT2BF22K * X0227381
JT2BF28K * X0227306
OP CODEDESCRIPTIONTIMEOPNT1T2
BD9006Adjust the Wire Harness Grommet
and/or Connector (both sides)0.487910±331505957
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
1. Carefully pry off the door speaker
cover and remove the nut using a 10
mm socket that secures the speaker
to the door.
2. Look through the door mirror harness
access hole and check the position of
the wire harness grommet and wire
harness connector ± the harness
connector should be inside the
grommet and the grommet should be
fully seated in the mirror housing.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Warranty
Information
Connector
and Grommet
Mirror Housing
Grommet Connector
CORRECT POSITION
Repair
Procedure

Toyota Supports ASE CertificationPage 1 of 3
BO020±99
Title:
SEAT COVER LOOSENESS
Models:
'99 Camry & Sienna
Technical Service
BULLETIN
December 17, 1999

On some 1999 Camry front seats and Sienna captain seats, the seat bottom cover may
become loose at the front lower J±clip. To correct this condition a change has been
made to the way the seat cover is fastened to the seat bottom.
1999 Camry & Sienna vehicles produced within the following VIN ranges.
MODEL/PLANTBETWEEN VIN
Camry (Plant 1)BG*XU575466 BF*XU578340 / BF*XU085983 BF*XU086274Camry (Plant 1)BG * XU575466 ± BF * XU578340 / BF * XU085983 ± BF * XU086274
Camry (Plant 2)BG * XU908651 ± BG * XU910853 / BF * XU932462 ± BF * XU932748
SiennaXU167107 ± XU168859
NOTE:
When working with sheet metal wear Kevlar Gloves to protect your hands.
Camry
OP CODECOMBODESCRIPTIONTIMEOPNT1T2
711041A&BRe±attach Lower Portion of1171071±xxxxx±xx6214711041A & BRe attach Lower Portion of
Front Seat Cover (RH & LH)1.171072±xxxxx±xx6214
Sienna
OP CODECOMBODESCRIPTIONTIMEOPNT1T2
711041A&BRe±attach Lower Portion of0671071±xxxxx±xx6214711041A & BRe attach Lower Portion of
Captain Seat Cover (RH & LH)0.671074±xxxxx±xx6214
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
BO021±99
Title:
SUNROOF OPERATION
Models:
'97 ± '99 TMMK Camry
Technical Service
BULLETIN
December 17, 1999

Some 1997 ± 1999 TMMK Camry vehicles may experience an interruption in sunroof
operation (not opening or closing). Changes have been made to the roof drip channel
guides to improve operation. The guides were modified to increase the clearance
between the sun shade and opening flange by 2 mm. A radius was added to eliminate
the sharp corners of the guides.
1997 ± 1999 TMMK Camry vehicles built before the production change.
MODELPLANTSTARTING VIN
Camry (TMMK)Plant 14T1BG*XU543595/BF*XU083791Camry (TMMK)Plant 24T1BG*XU901534/BF*XU932010
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
63222±AA010SameRoof Drip Channel Guide ± LH
63221±AA010SameRoof Drip Channel Guide ± RH
OPCODEDESCRIPTIONTIMEOPNT1T2
614141R & R Drip Channel Guide, Both RH and LH2.063222±AA0105383
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 1
BO025-01Title:
SUNVISOR VANITY MIRROR
IMPROVEMENT
Models:
'97 ± '01 NAP Camry
Technical Service
BULLETIN
October 12, 2001

Production changes have been implemented on the 1997 ± 2001 model year NAP Camry
vanity mirror assembly to improve strength and durability of the mirror cover hinge.
Mirror Cover Hinge
1997 ± 2001 model year NAP Camry vehicles.
MODELSTARTING VIN
2001 Camry4T1B#2#K#1U045764 (Line 1)
4T1B#2#K#1U798163 (Line 2)
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
74310±AA095±A0/B0/G074310±AA096±A0/B0/G0Right Sunvisor Assembly
74320±AA055±A0/B0/G074320±AA056±A0/B0/G0Left Sunvisor Assembly
Replace damaged sunvisor with a service part.
OP CODEDESCRIPTIONTIMEOPNT1T2
752101R & R RH and/or LH Sunvisor Assembly0.2
74310±AA095±##
or
74320±AA055±##
6216
Applicable Warranty*:
This repair is covered under the Toyota Comprehensive Warranty. This warranty is in
effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's
in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Repair
Procedure
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 1
BO028-00Title:
LEAKS INTO TRUNK
Models:
'97 - '01 Camry (U.S.), '98 - '01 Sienna,
'99 - '01 Solara & '01 Avalon
Technical Service
BULLETIN
November 3, 2000

A field fix is available for incidents of moisture and odors permeating into the vehicle.
The Quarter Panel Air Duct flaps may have become loose or missing. Replacing the
Quarter Panel Air Duct will remedy the condition.
1997 ± 2001 model year Camry (U.S. produced)
1998 ± 2001 model year Sienna
1999 ± 2001 model year Solara
2001 model year Avalon
MODELSTARTING VIN
2001 MY Camry, 4 cylinder4T1BG22K81U019710
4T1BG22KB1U768622
2001 MY Camry, 6 cylinder4T1BF28K11U116208
4T1BF22K51U958204
2001 MY Sienna4T3ZF13C#1U335575
2001 MY Solara2T1CF22P#1C435983
2001 MY Solara Convertible2T1FF28P#1C435448
2001 MY Avalon4T1BF28B11U123532
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
62940-AA01062940-AA011Quarter Panel Air Duct
Replace the Quarter Panel Air Duct.
OP CODEDESCRIPTIONTIMEOPNT1T2
BD0036R & R Quarter Panel Air Duct1.062940-AA0106257
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Repair
Procedure
Warranty
Information

BR002±94
BRAKE VIBRATION AND/OR PULSATIONPage 2 of 6
B. PEDAL PULSATION
Applying brakes causes the brake pedal to pulsate. This brake pulsation sometimes
causes the steering wheel to oscillate when the brakes are applied (See Figure 2 below).
2) CAUSE OF VIBRATION/PULSATION PROBLEMS
Brake rotor thickness variation causes brake vibration due to changes in the braking force as
thick/thin portions of the rotor pass the pads. Brake rotor thickness variation can be measured
with a micrometer as shown in Figure 3 below.
Figure 2
10 mm
Divide Into
8 Equal Parts & Measure
at each location
Thickness Variation = Maximum ± Minimum
Figure 3

Toyota Supports ASE CertificationPage 1 of 4
BR004±00
Title:
BRAKE PAD CLICKING NOISE
Models:
'90 ± '00 All Models
Technical Service
BULLETIN
October 20, 2000

A clicking type noise may be noticed when first applying the brakes after changing
vehicle travel direction (
Drive/Forward to Reverse, Reverse to Drive/Forward). This is a
normal noise caused by the required brake pad±to±caliper clearances. When the
direction of travel is changed, the brake pads may ªshiftº towards the new direction of
travel. When the brake pad contacts the caliper, a clicking noise may be heard.
To minimize this clicking noise, a disc brake caliper grease has been made available for
use during brake service/maintenance operations. Under normal usage conditions this
grease should be effective for a period of 6 months to 1 year.
1990 ± 2000 model year Toyota vehicles, all models.
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
N/A08887±80609Disc Brake Caliper Grease (50 g tube)
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
BRAKES
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 2
EG001±00
Title:
SINGLE CYLINDER MISFIRES
Models:
'99 Avalon, Camry, Sienna & Solara (CA Spec.)
Technical Service
BULLETIN
January 14, 2000

NOTE:
The information contained in this TSB updates EG013±99 dated December 17, 1999.
Some 1999 California Emission Specification Avalon, Camry (1MZ±FE), Sienna & Solara
(1MZ±FE) vehicles may exhibit a rough idle, and or a M.I.L. ªONª condition, in which a
single cylinder misfire code, or codes are present. Changes have been made in the fuel
injector production process to correct this condition.
1999 CA Emission Spec. TMMK produced Avalon, Camry (1MZ±FE), Sienna &
TMMC produced Solara (1MZ±FE) vehicles built between the VIN numbers listed
below.
MODELSTARTING VINENDING VIN
Avalon4T1BF1#B*XU2985044T1BF1#B*XU319557
Camry4T1BF2#K*XU0764034T1BF2#K*XU081214
Camry (cont.)4T1BF2#K*XU9300244T1BF2#K*XU931330
Sienna4T3ZF1#C*XU0908874T3ZF1#C*XU122589
Solara (U.S.)2T1CF2#P*XC1110832T1CF2#P*XC757508
Solara (Canada)2T1CF2#P*XC7441132T1CF2#P*XC162681
APPLICABLE PARTSQUANTITYPART NAME
23209±0A0106Fuel Injector
OP CODEVWCDESCRIPTIONTIMEOPNT1T2
895221NR & R Fuel Injector Assembly ± All1.823209±0A0100256
Applicable Warranty*:
This repair is covered under the Toyota Federal Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
Coverage is extended to 36 months or 50,000 miles, whichever occurs first, in the
states of California, Massachusetts, and Vermont due to state emission warranty
legislation.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
NOTE:
Be sure to enter the DTC No. in the Condition/Cause/Remedy section, if a DTC Code
appeared.
ENGINE
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 1
EG002±00
Title:
DIAGNOSTIC TROUBLE CODE P1133
Models:
'97 ± '99 Camry: 1MZ±FE CA Spec.
Technical Service
BULLETIN
February 25, 2000

TSB Revision Notice:
The information updated in this TSB is red
and underlined.
Under certain driving conditions, some 1MZ±FE equipped 1997 ± 1999 Camry California
Emission specification vehicles can exhibit a M.I.L. ªONº DTC P1133. An improved
Air/Fuel Ratio Sensor has been developed to correct this condition.
1997 ± 1999 Camry (1MZ±FE) with California Emission Specification.
MODEL YEARENGINESTARTING VIN
1999 Camry1MZ±FE4T1BF2#K * XU088001
4T1BF2#K * XU933227
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
89467±4102089467±41021Sensor, Air/Fuel
Should a M.I.L. ªONº condition with DTC P1133 be encountered, perform diagnostic
procedures as described in the Repair Manual.
If the problem source cannot be identified after checking all affected areas according
to the Repair Manual, the cause may be an Air/Fuel Ratio Sensor malfunction. In this
case, replace the Air/Fuel Ratio Sensor with the current part number listed above.
If the Exhaust Manifold threads are damaged by removal of the sensor, they can be
repaired by the proper use of a M18 x 1.5 tap.
OP CODEDESCRIPTIONTIMEOPNT1T2
895131R & R Air/Fuel Ratio Sensor0.389467±410209999
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
Coverage is extended to 36 months or 50,000 miles, whichever occurs first, in the
states of California and Massachusetts due to state emissions warranty legislation.
NOTE:
Please enter the DTC in the condition/Cause/Remedy section when applying for
warranty reimbursement.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
ENGINE
Introduction
Applicable
Vehicles
Production
Change
Information
Parts
Information
Repair
Procedure
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 23
EG003-02Title:
READINESS MONITOR DRIVE PATTERNS
Models:
All '96 ± '02
Technical Service
BULLETIN
March 29, 2002

TSB REVISION NOTICE:
The information updated in this TSB is red
and underlined.
The On±Board Diagnostic (OBDII) system is designed to monitor the performance of
emission±related components and report any detected abnormalities in the form of
Diagnostic Trouble Codes (DTCs). Since the various components need to be monitored
during different driving conditions, the OBDII system is designed to run separate
monitoring programs called Readiness Monitors. Many state Inspection and
Maintenance (I/M) programs require that vehicles complete their Readiness Monitors
prior to beginning an emissions test.
The current status of the Readiness Monitors can be seen by using the Toyota Diagnostic
Tester with version 9.0 software (or newer), or a generic OBDII Scantool.
To view the Readiness Monitor status using the Toyota Diagnostic Tester, select ªMonitor
Statusº from the Enhanced OBDII Menu.
A status of ªcompleteº indicates that the necessary conditions have been met to run the
performance tests for the related Readiness Monitor.
The Readiness Monitor will be reset to ªincompleteº if:

ECU has lost power (battery or fuse).

DTCs have been cleared.

The conditions for running the Readiness Monitor have not been met.
In the event that any Readiness Monitor shows ªincomplete,º follow the appropriate
Readiness Monitor Drive Pattern to change the readiness status to ªcomplete.º
Refer to the Readiness Monitor Drive Pattern Application Table to determine which
drive pattern should be followed.
SECTIONPAGE(S)
Readiness Monitor Drive Pattern Application Tables3±9
Readiness Monitor Drive Patterns
1EGR Monitor (All Except 1FZ±FE Engine)10
2EGR Monitor (For 1FZ±FE Engine)11
3Catalyst Monitor (O2S Type)12
4Catalyst Monitor (AF Sensor Type)13
5EVAP Monitor (Internal Pressure Monitor/Non±Intrusive Type)14±15
6EVAP Monitor (Vacuum Pressure Monitor/Intrusive Type)16±17
7EVAP Monitor (Without Leak Detection)18
8EVAP Monitor (For Prius)19±20
9Oxygen Sensor Monitor (Front and Rear O2S System)21
10Oxygen/AF Sensor Monitor (Front AF Sensor and Rear O2S System)22
11Oxygen/AF Sensor Heater Monitor23

All 1996 ± 2002 model year Toyota vehicles.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
ENGINE
Introduction
Contents
Applicable
Vehicles
Warranty
Information