check engine TOYOTA GR86 2022 (in English) Owner's Guide

2284-6. Using other driving systems
1The detection range of the radar
sensors
2 Area out of detection range of
the radar sensors
Parked vehicle
Vehicle that may not be
detected
Example 2
1 The detection range of the radar
sensors
Vehicle that may be detected
The system may detect that a vehicle
is passing in front of your vehicle.
Always be sure to check the
surroundings with your eyes when reversing the vehicle.
■Operating conditions
The BSD/RCTA will operate when
all of the following conditions are
met.
 The engine switch is in ON.
 The BSD/RCTA warning light
and BSD/RCTA OFF indicator
are turned off.
 The vehicle is driven at speeds
above 12 km/h (7 mph) (except
when reversing).
 The shift lever is in R. (RCTA
only)
The BSD/RCTA will not operate in
the following situations.
 The BSD/RCTA OFF indicator
appears.
 The vehicle speed is below 10
km/h (6 mph) even when the
BSD/RCTA OFF indicator does
not appear (except when revers-
ing).
●In the following cases, the BSD/RCTA
will stop operating and the BSD/RCTA warning light will appear.
• When a malfunction occurs in the sys-
tem, including the BSD/RCTA approach indicator
●If the BSD/RCTA warning light appears, exercise proper caution.
( P.232)
●In the following cases, the BSD/RCTA
will temporarily stop operating (or may
stop operating) and the BSD/RCTA
WA R N I N G
An approaching vehicle may not
be detected because the detection
range is limited by the parked vehicle
. Always be sure to check the
surroundings with your eyes when
reversing the vehicle.
A
C
System operation

2444-6. Using other driving systems
●Do not wipe the camera with alcohol,
benzine or paint thinner.
Otherwise, discolora tion may occur. To remove contamination, wipe the
camera with a cloth moistened with a
diluted neutral detergent. Then wipe it with a soft, dry cloth.
●When waxing the vehicle, be careful not to apply the wax to the camera. If
it comes in contact with the camera,
moisten a clean cloth with a diluted neutral detergent to remove the wax.
●The camera lens has a hard coating to help prevent scratches. However,
when washing the vehicle or cleaning
the camera lens, be careful not to
scratch the camera lens. Do not use a washing brush directly on the camera
lens. The image quality of the rear
view camera may deteriorate.
●Strong light shined on the camera lens
may develop vertical lines around the light source. This is not a malfunction.
●Under the fluorescent light, the display
may flicker. However, this is not a mal-
function.
●The image of the rear view camera
may be slightly different from the actual color of the objects.
●If there is a malfunction on the multi-media system screen, refer to “Multi-
media owner’s manual”.
Rear view camera
A rear view camera is attached
to the trunk lid. When the
engine switch is in ON and the
shift lever is set to R, the rear
view camera automatically dis-
plays the rear view image
behind the vehicle on the mul-
timedia system screen.
WA R N I N G
●Since the rear view camera uses a
wide-angle lens, the image on the monitor is different from the actual
view in terms of distance.
●Since the range of the image on the
monitor is limited, always check the
rear view and the surrounding area with your eyes and mirrors, and
move backward at a slow speed.
Moving backward only by checking the rear view image from the cam-
era could cause an accident.
●Do not disassemble or modify the
camera, switch or wiring. If smoke
comes out or you smell a strange odor, stop using the rear view cam-
era immediately.
Contact any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer for
an inspection. Continued use may result in accident, fire or electric
shock.
NOTICE
●When washing your vehicle with a high-pressure washer, do not allow
water to touch the camera directly.
Entry of water in the camera lens may result in condensation, mal-
function, fire or electric shock.
●Since the camera is a precision
device, do not subject it to strong
impacts. Otherwise, malfunction, fire or electric shock may occur.

247
4
4-6. Using other driving systems
Driving
Approx. 1 m (3 ft) from the
bumper (yellow horizontal line)
Approx. 0.5 m (1.5 ft) from the
bumper (red horizontal line)
Vehicle centerline
Dynamic guidelines
When the shift lever is set to R, the
multimedia system screen the help
lines together with the rear view
image.
If you shift to the R range within several
seconds after turning on the engine
switch, the warning message may not be displayed. Wait for several seconds
after turning on the engine switch before
shifting to the R range. Then, the warn- ing message will be displayed.
When “Steering Angle Lines” is off, the dynamic guidelines will be disappear on
the multimedia system screen. To turn
the dynamic guidelines on and off, refer to “Multimedia owner’s manual”.
■Difference between screen
image and actual road
The distance markers show the dis-
tance for a level road when the
vehicle is not loaded. It may be dif-
ferent from the actual distance
depending on the loading condi-
tions or road conditions.
When there is an upward slope
at the back
1 m (3 ft)
The distance on the screen looks
farther than the actual distance.
When there is a downward slope
at the back
1 m (3 ft)
The distance on the screen looks
nearer than the actual distance.
When cargo is loaded, the rear view dis-
WA R N I N G
●When moving backward, always
check the back with your eyes with-
out relying on the help lines. Otherwise, it may cause an acci-
dent or injury.
●The actual position may be different
from the indication of the help lines.
●Differences may occur due to the
number of passengers or the
loaded cargo.
●When the vehicle is on a slope or
inclined against the road, the indi- cation is different from the actual
position.
D
A
A

253
4
4-6. Using other driving systems
Driving
Use snow mode for accelerating and
driving on slippery road surfaces such
as snow.
The snow mode indi cator comes on.
■Sport mode
●In sport mode, lower gears are used and gears change at a higher engine
speed.
●In the following situations, it may not
be possible to change to sport mode.
When the mode cannot be changed to sport mode, a buzzer will sound and a
message will be displayed on the
multi-information display. • When the Adaptive Cruise Control or
Conventional Cruise Control is operat-
ing • When the engine is cold
■Snow mode
To prevent slipping, 1st gear cannot be
selected when in snow mode.
■Automatic deactivation of sport mode and snow mode
In the following situations, the driving
mode is automatically deactivated:
●When the engine is turned off after
driving in sport mode or snow mode.
●When the Adaptive Cruise Control or
Conventional Cruise Control is acti-
vated while driving in sport mode.
●When in sport mode and stop-
ping/starting off is automatically per- formed in second gear. ( P.144)
When the engine switch is turned to
ON, the hill-start as sist control ON
indicator will illuminate.
When the hill-start assist control
operates, the indicator will flash.
1 Park your vehicle in a flat, safe
location.
Make sure that the parking brake is
securely engaged.
2 Stop the engine by turning the
engine switch off.
3 Start the engine and check that
the ABS warning light and slip
indicator are off.
Hill-start assist control
Hill-start assist control helps to
maintain braking force to
assist starting off forward
while facing uphill or starting
off backward while facing
downhill.
Hill-start assist control ON
indicator
Disabling hill-start assist
control

2544-6. Using other driving systems
4Press and hold the switch
for approximately 30 seconds.
Check that the TRC OFF and VSC OFF
indicators illuminate and then turn off.
5 Within 5 seconds after the indi-
cator lights turn off, release the
switch. Then, press the
switch again within 2 seconds of
releasing it.
The hill-start assist control ON indicator will turn off and then illuminate.
6 Turn the engine switch off.
7 Start the engine again and
check that the hill-start assist
control ON indicator turns off.
Hill-start assist control will be disabled.
To enable hill-star t assist control,
perform steps 1 through 7 again.
■When enabling the hill-start assist control
●If the hill-start assi st control ON indi-
cator does not turn off or a mistake was made during the procedure, turn
the engine switch off and start the pro-
cedure from step 4 again.
●If the switch is pressed and held
for 30 seconds or more, the TRC OFF indicator and VSC OFF indicator will
turn off and the switch will become
inoperable. In this case, the VSC will
operate in normal mode. ( P.257) If the engine switch is turned off and
then the engine is started again, oper-
ation of the switch will become
possible.
■Operating conditions of hill-start
assist control
When the following conditions are met, the hill-start assist control will operate:
●Vehicles with an automatic transmis-sion: The shift lever is in D or M (when
starting off forward on while facing
uphill) or in R (when starting off back- ward while facing downhill).
●Vehicles with a manual transmission: The shift lever is in a position other
than R (when starting off forward while
facing uphill) or in R (when starting off backward while facing downhill).
●The vehicle is stopped.
●The accelerator pedal is not
depressed.
●The parking brake is not engaged.
■Hill-start assist control will not
operate when
Hill-start assist control will not operate
when any of the following conditions are
met:
●Vehicles with an automatic transmis-
sion: The shift lever is in a position other than D or M (when facing uphill)
or in a position other than R (when
facing downhill).
●Vehicles with a manual transmission:
The shift lever is in R (when facing uphill) or in a position other than R
(when facing downhill).
●Vehicles with an automatic transmis- sion: The accelerator pedal is
depressed.
●The parking brake is applied.
●Vehicles with a manual transmission: The clutch is engaged.
●Approximately 2 seconds have elapsed since the brake pedal was

6
281
6
Maintenance and care
Maintenance and care
.6-1. Maintenance and care
Cleaning and protecting the
vehicle exterior ............... 282
Cleaning and protecting the
vehicle interior ................ 285
Cleaning and protecting the
Ultrasuede®area ............. 287
6-2. Maintenance
Maintenance requirements
....................................... 289
6-3. Do-it-yourself maintenance
Do-it-yourself service precau-
tions ................................ 291
Hood ................................. 293
Positioning a floor jack ...... 294
Engine compartment ........ 295
Tires .................................. 301
Replacing the tire.............. 308
Tire inflation pressure ....... 312
Wheels.............................. 313
Air conditioning filter ......... 314
Electronic key battery ....... 316
Checking and replacing fuses
....................................... 319
Light bulbs ........................ 321

2906-2. Maintenance
request that a record of maintenance
be kept.
■Does your vehicle need repairs?
Be on the alert for changes in perfor- mance and sounds, and visual tip-offs
that indicate service is needed. Some
important clues are:
●Engine missing, stumbling or pinging
●Appreciable loss of power
●Strange engine noises
●A fluid leak under the vehicle (How-
ever, water dripping from the air con- ditioning system after use is normal.)
●Change in exhaust sound (This may indicate a dangerous carbon monox-
ide leak. Drive with the windows open
and have the exhaust system checked immediately.)
●Flat-looking tires, excessive tire squeal when cornering, uneven tire
wear
●Vehicle pulls to one side when driven
straight on a level road
●Strange noises related to suspension
movement
●Loss of brake effectiveness, spongy
feeling brake pedal or clutch pedal
(vehicles with a manual transmission),
pedal almost touches the floor, vehicle pulls to one side when braking
●Engine coolant temperature continu-ally higher than normal ( P. 8 8 )
If you notice any of these clues, take
your vehicle to any authorized Toyota retailer or Toyota authorized repairer, or
any reliable repairer as soon as possi-
ble. Your vehicle may need adjustment or repair.

295
6
6-3. Do-it-yourself maintenance
Maintenance and care
Fuse boxes ( P.319)
Battery ( P.298)
Engine oil level dipstick ( P.295)
Engine oil filler cap ( P.295)
Washer fluid tank ( P.300)
Electric cooling fans
Condenser ( P.298)
Radiator ( P.298)
Engine coolant reservoir ( P. 2 9 7 )
For right-hand drive vehicles:
The battery is located on the opposite side of the engine compartment.
With the engine at operating tem-
perature and turned off, check the
oil level on the dipstick.
Engine compartment
Components
A
C
D
Checking and adding the
engine oil

2966-3. Do-it-yourself maintenance
■Checking the engine oil
1 Park the vehicle on level
ground. After warming up the
engine and turning it off, wait
more than 5 minutes for the oil
to drain back into the bottom of
the engine.
2 Holding a rag under the end,
pull the dipstick out.
3 Wipe the dipstick clean.
4 Reinsert the dipstick fully.
5 Holding a rag under the end,
pull the dipstick out and check
the oil level.
When checking the oil, look at both
sides of the dipstick and use the lower measurement to determine the level of
oil.
6 Wipe the dipstick and reinsert it
fully.
Low
Full
■Checking the oil type and pre-
paring the item needed
Make sure to check the oil type and
prepare the items needed before
adding oil.
 Engine oil selection
 P.370
 Oil quantity (Low  Full)
1.0 L (1.1 qt., 0.9 Imp. qt.)
 Item
Clean funnel
■Adding engine oil
If the oil level is below or near the
low level mark, add engine oil of the
same type as that already in the
engine.
1 Remove the oil filler cap by turn-
ing it counterclockwise.
2 Add engine oil slowly, checking
the dipstick.
3 Install the oil filler cap by turning
it clockwise.
■Engine oil consumption
A certain amount of engine oil will be
consumed while driving. In the following situations, oil consumption may
increase, and engine oil may need to be A

297
6
6-3. Do-it-yourself maintenance
Maintenance and care
refilled in between oil maintenance inter-
vals.
●When the engine is new, for example
directly after purchasing the vehicle or after replacing the engine
●If low quality oil or oil of an inappropri-ate viscosity is used
●When driving at high engine speeds or with a heavy load, or when driving
while accelerating or decelerating fre-
quently
●When leaving the engine idling for a
long time, or when driving frequently through heavy traffic
The coolant level is satisfactory if it
is between the “FULL” and “LOW”
lines on the reservoir when the
engine is cold.
■Engine coolant reservoir
Reservoir cap
“FULL” line
“LOW” line
If the level is on or below the “LOW”
line, add coolant up to the “FULL” line.
( P.362)
■Coolant selection
Only use “TOYOTA Genuine 50/50
Pre-mixed Super Long Life Coolant BLUE” or a similar high quality ethylene
glycol based non-silicate, non-amine,
non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.
WA R N I N G
■Used engine oil
●Used engine oil contains poten-
tially harmful contaminants which may cause skin disorders such as
inflammation and skin cancer, so
care should be taken to avoid pro- longed and repeated contact. To
remove used engine oil from your
skin, wash thoro ughly with soap and water.
●Dispose of used oil and filters only in a safe and acceptable manner.
Do not dispose of used oil and fil-
ters in household trash, in sewers or onto the ground. Call any author-
ized Toyota dealer or repairer, or
another duly qualified and equipped professional, service station or auto
parts store for information concern-
ing recycling or disposal.
●Do not leave used engine oil within
the reach of children.
NOTICE
■To prevent serious engine dam-
age
Check the oil level on a regular basis.
■When replacing the engine oil
●Be careful not to spill engine oil on
the vehicle components.
●Avoid overfilling, or the engine
could be damaged.
●Check the oil level on the dipstick
every time you refill the vehicle.
●Be sure the engine oil filler cap is
properly tightened.
Checking the coolant
A
C