seat memory TOYOTA LAND CRUISER 1986 Factory User Guide

H01021AB0119H01081 H10600H10626
"u
ONAirbag
Sensor
Assembly
DTC B0133/62 DLC3
TC CG
P/T Squib RH
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-789
982 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib RH.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner RH (P/T squib RH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0133/62 is not output.
HINT:
Codes other than code B0133/62 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner RH
(P/T squib RH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.

H01018AB0119H01086
H10600H10628
"u
ONAirbag
Sensor
Assembly
DTC B0135/73
DLC3
TC CG
P/T Squib LH
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-793
986 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner LH (P/T squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0135/73 is not output.
HINT:
Codes other than code B0135/73 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner LH
(P/T squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.

H01017H02139AB0119H01087 H10600H10629
Airbag
Sensor
Assembly
PL+
PL-
DTC B0136/74
ON
DLC3
TC CG
P/T Squib LHFloor No. 1 Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-795
988 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect PL+ and PL- of the floor No.
1 wire connector on the seat belt pretensioner LH (P/T
squib LH) side.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0136/74 is not output.
HINT:
Codes other than code B0136/74 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK

AB0119H01018
H01087 H10600H10630
"u
ONAirbag
Sensor
Assembly
DTC B0136/74 DLC3
TC
CG
P/T Squib LHFloor No. 1 Wire
DI-796
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
989 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner LH (P/T squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0136/74 is not output.
HINT:
Codes other than code B0136/74 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner LH
(P/T squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.

H01017H02139AB0119H01084 H10600H10631
Airbag
Sensor
Assembly
PL+
PL-
DTC B0137/71ON " u
DLC3
TC CG
P/T Squib LHFloor No. 1 Wire
DI-798
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
991 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect PL+ and PL- of the floor No.
1 wire connector on the seat belt pretensioner LH (P/T
squib LH) side.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0137/71 is not output.
HINT:
Codes other than code B0137/71 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK

H01018
AB0118AB0119H01084 H10600H10632
"u
ONAirbag
Sensor
Assembly
DTC B0137/71 DLC3
TC CG
P/T Squib LH
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-799
992 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner LH (P/T squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0137/71 is not output.
HINT:
Codes other than code B0137/71 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner LH
(P/T squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.

H01017H02139AB0119H01085 H10600H10633
Airbag
Sensor
Assembly
PL+
PL-
DTC B0138/72
ON " u
DLC3
TC CG
P/T Squib LHFloor No. 1 Wire
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-801
994 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connector to the airbag sensor assembly.
(b) Using a service wire, connect PL+ and PL- of the floor No.
1 wire connector on the seat belt pretensioner LH (P/T
squib LH) side.
(c) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0138/72 is not output.
HINT:
Codes other than code B0138/72 may be output at this time, but
they are not relevant to this check.
NG Replace airbag sensor assembly.
OK

AB0119H01018
H01085 H10600H10634
"u
ONAirbag
Sensor
Assembly
DTC B0138/72 DLC3
TC CG
P/T Squib LH
DI-802
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
995 Author
: Date
:
2004 LAND CRUISER (RM1071U)
4 Check P/T squib LH.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the seat belt pretensioner LH (P/T squib LH)
connector.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B0138/72 is not output.
HINT:
Codes other than code B0138/72 may be output at this time, but
they are not relevant to this check.
NG Replace seat belt pretensioner LH
(P/T squib LH).
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check. If the malfunctioning part can not be
detected by the simulation method, replace all SRS components including the wire harness.

AB0119H10600H16831H19293
ON
DLC3
CG TCDTC B1153/25
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI-837
1030 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Is DTC B1153/25 output ?
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B1153/25 is output.
HINT:
Codes other than code B1153/25 may be output at this time, but
they are not relevant to this check.
NO The malfunctioning part can now be considered
normal. To make sure of this, use the simulation
method to check.
YES
2 Is connector of the seat position sensor assembly properly connected ?
NO Connect connector.
YES
3 Prepare for inspection (See step 1 on DI-923).

H10600AB0119H21741
Airbag
Sensor
Assembly
ON
DLC3DTC B1153/25
CG
TC
" u
" u
Seat
Position
Sensor
Assembly
DI-840
- DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1033 Author
: Date
:
2004 LAND CRUISER (RM1071U)
7 Check seat position sensor assembly.
PREPARATION:
(a) Turn the ignition switch to LOCK.
(b) Disconnect the negative (-) terminal cable from the bat-
tery, and wait at least for 90 seconds.
(c) Connect the connectors of the seat position sensor as-
sembly and the airbag sensor assembly.
(d) Connect the negative (-) terminal cable to the battery,
and wait at least for 2 seconds.
CHECK:
(a) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(b) Clear the DTC stored in memory (See page DI-692).
(c) Turn the ignition switch to LOCK, and wait at least for 10
seconds.
(d) Turn the ignition switch to ON, and wait at least for 10 se-
conds.
(e) Check the DTC (See page DI-692).
OK:
DTC B1153/25 is not output.
HINT:
Codes other that code B1153/25 may be output at this time, but
they are not relevant to this check.
NG Replace seat position sensor assembly,
then go to next step.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.