transfer box TOYOTA LAND CRUISER 1996 J80 Workshop Manual

Q08467
Rear Propeller
ShaftTransfer Shift
Lever Boot
Transmission Shif
Lever Assembly
Rear Console Box
Front Console Box
Engine Rear Mounting
Plug for Hydraulic Test
Oil Cooler Pipe Transfer Shift
Control Link
Transfer Shift
Lever Cushion
x 6
x 6 Clip
Transfer Shift
Lever Knob
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−19
803
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−21
1996 LAND CRUISER (RM451U)
(c) Remove the transfer shift lever knob.
(d) Remove the 4 screws and console.
(e) Remove the 4 screws and transfer shift lever boot.
(f) Remove the 3 bolts and console box.
(g) Disconnect the 3 connectors.
(h) Remove the 6 screws and transmission shift lever assem-
bly.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−72
−
ENGINE MECHANICAL ENGINE UNIT
1996 LAND CRUISER (RM451U)
24. REMOVE FRONT AND REAR PROPELLER SHAFTS
(a) Put matchmarks on the flanges.
(b) Remove the 4 bolts and nuts.
(c) Remove the 4 nuts.
(d) Remove the propeller shaft.
25. REMOVE TRANSFER SHIFT LEVER
(a) Remove the nut and transmission control rod.
(b) Remove the transfer shift lever knob.
(c) Remove 4 screws.
(d) Lift up the console slightly in order to disconnect the con-
nector.
(e) Remove the console.
(f) Remove the 3 bolts and console box.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−78
−
ENGINE MECHANICAL ENGINE UNIT
1996 LAND CRUISER (RM451U)
15. INSTALL TRANSFER SHIFT LEVER
(a) Install the shift lever and hose clamp with the 4 bolts.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(b) Connect the shift rod and install the pin.
(c) Install the transfer shift lever boot and transmission shift lever assembly with the 10 bolts.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
(d) Connect the 3 connectors to the transmission shift lever assembly.
(e) Install the console box with the 3 bolts.
(f) Connect the pattern select switch connector.
(g) Install the console with the 4 screws.
(h) Install the transfer shift lever knob.
(i) Shift the shift lever to N position.
(j) Fully turn the control shaft lever back and return 2 notches. It is now in neutral position.
(k) Connect the transmission control rod with the nut.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

RS0PE−01
−
SUPPLEMENTAL RESTRAINT SYSTEM AIRBAG SENSOR ASSEMBLY
RS−33
1996 LAND CRUISER (RM451U)
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and various
computers unless absolutely necessary.
(If the IC terminals are touched, the IC may be destroyed by
static electricity.)
1. REMOVE THESE PARTS:
(a) Transfer shirt knob
(b) Front console box
2. REMOVE AIRBAG SENSOR ASSEMBLY
(a) Disconnect the connector.
NOTICE:
Remove the connector with the sensor assembly installed.
(b) Using a torx wrench remove the 4 screws and the airbag sensor assembly.
Torx wrench: T40 (Part No. 09042 −00020 or locally
manufactured tool)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010