change time TOYOTA LAND CRUISER 2007 J200 Navigation Manual

cxiii
(d) Set as destination
Touch the “Enter ” switch on the “Set
Dealer” screen. The screen changes and
displays the map location of the regis-
tered dealer and the “Route Preference”.
(See
“ — Entering Destination” on page xlviii.)
Calendar with memo
This system informs you of a memo entry.
At the specified date, the memo informa-
tion will be displayed when the naviga-
tion system is in operation. The memo in-
formation screen will appear every time
the system is turned on. To disable this
screen, touch the
“Do not display
this message again”
switch.1. Push the
“INFO” button to display
the “Information Menu” screen.
5u004
2. Touch the “Calendar” switch to dis-
play the “Calendar” screen.

cl If manual switching of air intake is de-
sired
UNX506
The air intake control button is used to switch
the air intake between the OUTSIDE AIR
mode and RECIRCULATED AIR mode.
With the button in the OUTSIDE AIR mode,
the OUTSIDE AIR mode indicator light will
come on and the system will take fresh out-
side air into the vehicle.
If quick circulation of cooled air is desired,
push the air intake control button for RECIR-
CULATED AIR. The RECIRCULATED AIR
mode indicator light will come on.
For normal use, it is best to keep the air in-
take control button set to OUTSIDE AIR
mode. If recirculated air is used during heat-
ing, the windows will fog up more easily.If the engine coolant temperature becomes
extremely high, the RECIRCULATED AIR
mode is automatically selected. This is not
a malfunction. When the engine coolant
temperature is lowered, the previous mode
resumes.
In the following cases, the RECIRCULATED
mode may change to the OUTSIDE AIR
mode automatically to prevent interior fog.
When the outside temperature becomes
lower than 4C (39F).
When the air conditioning compressor
malfunctions.
When the air conditioning cooler refriger-
ant decreases.If manual onoff of the air conditioning is
desired
Push the “A/C” switch to turn the air condi-
tioning on and push it again to turn the air
conditioning off. If you turn off the air condi-
tioning manually, the EXHAUST GAS AU-
TOMATIC mode will be cancelled.
If the outside temperature is lowered down to
around 0C (32F), the air conditioning will
turn off automatically. At this time, the indica-
tor on the A/C button is off and the EX-
HAUST GAS AUTOMATIC indicator light re-
mains on. However, the EXHAUST GAS
AUTOMATIC mode does not operate.
When the air conditioning turns on as with
the raised temperature, the EXHAUST GAS
AUTOMATIC mode resumes.
If the system is used for ventilation, heating
in dry weather or removing frost or exterior
fog on the windshield, turn the air condition-
ing off once it is no longer required. This will
improve fuel economy. The air conditioning
can be used for year−round automatic tem-
perature control including cooling and dehu-
midifying operation.

clxi
(b) Presetting a station
lxb001a
1. Tune in the desired station.
2. Touch one of the station selector
switches (16) and hold it until a beep is
heard. This sets the station to the switch
and the frequency appears on the switch.
Each switch can store FM1, FM2 and AM.
To change the preset station to a different
one, follow the same procedure.
The preset station memory is cancelled
when the power source is interrupted by bat-
tery disconnection or a blown fuse.
(c) Selecting a station
Your Toyota has an electronic tuning radio
(ETR). Tune in the desired station using one
of the following methods.
Preset tuning: Touch the switch (1−6) or
push the “
” or “” side of the “CH” button
for the station you want. The switch (1−6) is
highlighted in green and station frequency
appears on the display.
Manual tuning: Turn the “TUNE” knob brief-
ly. Each time you turn the knob, the radio will
step up or down to another frequency.
Seek tuning: Push the “
” or “” side of
the “SEEK” button and hold it until you hear
a beep. The radio will begin seeking up or
down for a station of the nearest frequency
and will stop on reception. Each time you
push the button, the stations will be
searched out one after another.
lxb001a
Scan tuning:Touch the “SCAN” switch
briefly. “SCAN” appears on the display. The
radio will find the next station up or down the
band, stay there for a few seconds, and then
scan again. To select a station, touch the
“SCAN” switch a second time.
Preset scan tuning: Touch the “SCAN”
switch and hold it until you hear a beep. “P.
SCAN” appears on the display. The radio
will tune in the next preset station up or down
the band, stay there for a few seconds, and
then move to the next preset station. To se-
lect a station, touch the “SCAN” switch a se-
cond time.

clxii
(d) RDS (Radio Data System)
Program type
lxb001a
When you touch the “TYPE ” or “TYPE
” switch on the screen, the current pro-
gram type receiving from RDS station ap-
pears on the display.
If the system receives no RDS stations, “NO
PTY” appears on the display.Each time you touch the “TYPE ” or
“TYPE ” switch, the program type
changes as in the following:
ROCK
EASY LIS (Easy listening)
CLS/JAZZ (Classical music and Jazz)
R&B (Rhythm and Blues)
INFORM (Information)
RELIGION
MISC.
ALERT (Emergency message)
lxb003a
When a program is set, “TYPE SEEK”
switch appears. Touch the switch and the
system starts to seek the station in the rele-
vant program type.
Traffic program: A station that regularly
broadcasts traffic information is auto-
matically located.
When you push the “TRAF” button, “TRAF
SEEK” appears on the display and the radio
will start seeking any traffic program station.
If any traffic program station is not found,
“NOTHING” appears and the previous mode
returns.
If the traffic program station is found, the
name for traffic program station is displayed
and “TRAF” is lit for a while until traffic an-
nouncement is received.
VI

clxiii
Radio text
lxb001a
If the system receives a radio text from RDS
station, “MSG” appears on the display.
Touch the “MSG” switch, and a text mes-
sage is displayed on the screen.
lxb005a
In case a text message is not accepted in a
screen, you can touch the “MSG” switch
and hold it to display the rest of the message.
When the system can show the station
name, “RDS” appears on the display. Each
time you touch the “MSG” switch, indication
on the display changes from the band to the
station name, a radio text in this order. After
six seconds passes, indication returns to the
band.
Radio operation (XM
satellite radio broadcast)
To listen to a satellite radio broadcast in your
vehicle, an additional genuine Toyota satel-
lite receiver and antenna must be purchased
and installed, and the subscription to the
XMsatellite radio is necessary.

clxviii
(h) If the satellite radio tuner malfunctions
When problems occur with the XM tuner, a message will appear on the display. Referring to the table below to identify the problem, take the
suggested corrective action.
ANTENNA
The XM antenna is not connected. Check whether the XM antenna cable is attached securely.
A short−circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer.
UPDATING
You have not subscribed to the XM satellite radio. The radio is being updated with the latest encryp-
tion code. Contact the XM satellite radio for subscription information. When a contact is canceled,
you can choose the “CH000” and all free−to−air channels.
The premium channel you selected is not authorized. Wait for about 2 seconds until the radio returns
to the previous channel or “CH001”. If it does not change automatically, select another channel. If you
want to listen to the premium channel, contact the XM satellite radio.
NO SIGNALThe XM signal is too weak at the current location. Wait until your vehicle reaches a location with a
stronger signal.
LOADINGThe unit is acquiring audio or program information. Wait until the unit has received the information.
OFF AIRThe channel you selected is not broadcasting any programming. Select another channel.
−−−−−There is no song/program title or artist name/feature associated with the channel at that time. No ac-
tion needed.
−−−The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the
previous channel or “CH001”. If it does not change automatically, select another channel.
The XM Listener Care Center is also available on the phone, please call (800) 967−2346 during the following hours:
Monday – Saturday: 7 a.m. – 1 a.m. Sunday: 12 p.m – 12 a.m.
VI

clxxiv When the magazine is set completely, the
system will be in a “Load” cycle for approxi-
mately 30 seconds while the system
searches for discs in the magazine. Upon
completion of this cycle, the DVD player unit
will be ready to play. If the “DISC” button is
pushed during the “Load” cycle, “LOAD” ap-
pears on the display until the system has
completed the load cycle, after which the
system will begin normal play.
CAUTION
To reduce the chance of injury in case
of an accident or a sudden stop, always
keep the console box closed while
driving.
(b) Playing a disc
ung627
Push the “DISC” button if the magazine is
already loaded in the player.
The “DVD CHANGER” screen appears on
the display.
The discs set in the magazine are played
continuously, starting with disc number 1.
The disc number of the disc currently being
played, the track number and the time from
the beginning of the program are shown on
the display.
(c) Selecting a desired disc
On the screen: Touch the desired disc
number.
The selected disc number is highlighted in
green.
The player will start playing the selected disc
from the first track.
On the audio panel: Push the “
” or “”
side of the “DISC” button.
When you release the button, the player will
start playing the selected disc from the first
track.VI

clxxvii
(e) Operating a DVD video disc
NOTE: The playback condition of some
DVD video discs may be determined by a
DVD video software producer. This DVD
player plays a disc as the software pro-
ducer intended. So some functions may
not work properly. Be sure to read the in-
struction manual for the DVD video disc
separately provided. For the detailed in-
formation about DVD video discs, see
“(h) DVD player and DVD video disc infor-
mation”Precautions on DVD video disc
When recording with a DVD video or video
CD, audio tracks may not record in some
cases while the menu is displayed. As audio
will not play in this case, verify that the video
tracks are playing and then activate play-
back.
When playback of a disc is completed:
If an audio CD is playing, the next CD will
be selected and playback will begin auto-
matically.
If a DVD video or video CD is playing,
playback will stop or the menu screen will be
displayed. The next disc will not play back
automatically. (Audio tracks cannot be heard
while the disc is stopped)
The title/chapter number and playback time
display may not appear while playing back
certain DVD video discs.
CAUTION
Conversational speech on some DVDs
is recorded at a low volume to empha-
size the impact of sound effects. If you
adjust the volume assuming that the
conversations represent the maximum
volume level that the DVD will play, you
may be startled by louder sound ef-
fects or when you change to a different
audio source. The louder sounds may
have a significant impact on the human
body or pose a driving hazard. Keep
this in mind when you adjust the vol-
ume.
VI

clxxx (iv) Selecting a menu item
Enter the menu item using “ ”, “”, “
”
or “” switches and touch “Enter”. The
player starts playing video for that menu
item. (For details, see the manual that
comes with the DVD video disc provided
separately.)
Each you push “Move Buttons” switch,
the switches on the screen move upward
and downward.
When you push “OFF” switch, the displayed
switches do not display. To display them
again, push “ON” switch.
Touch “Back”, the previous screen returns.(v) Searching by titleEnter the title number using “–”, “+” and
“+10” switches and touch “Enter”. The
player starts playing video for that title
number.
When you push “
” or “” on the “TRACK”
switch, you can select a chapter.
Touch “Back”, and the previous screen re-
turns.(vi) Changing the subtitle language
Each time you touch “Sub title”, the lan-
guage is selected from the ones stored in
the discs and changed.
To turn off the subtitle, touch “Hide”.
Touch “Back”, and the previous screen re-
turns.

clxxxi (vii) Changing the audio language
Each time you touch “Audio”, the lan-
guage is selected from the ones stored in
the discs and changed.
Touch “Back”, and the previous screen re-
turns.(viii) Changing the angleThe angle can be selected for discs that
are multiangle compatible when the
angle mark appears on the display.
Each time you touch “Angle”, the angle
changes.
Touch “Back”, and the previous screen re-
turns.(ix) Setup menuThe initial setting can be changed.
Audio language
You can change the audio language.
1. Touch “Audio Lang.”
2. Touch the language you want to hear
on the “Select Audio Lang.” screen and
“Enter”.
If you cannot find the language you want to
hear on this screen, touch “Others” and en-
ter a language code. For the entry of lan-
guage code, see the following “(x) Entry of
language code”.
VI