transmission TOYOTA MR2 SPYDER 2003 W30 / 3.G User Guide

822003 MR2 from Aug. ’03 Prod. (OM17511U)
(l) Power Steering System WarningLight
This light warns that there is a problem
in your power steering system.
If the light comes on while you are driv-
ing, have your vehicle checked by your
Toyota dealer as soon as possible.
(m) Key Reminder Buzzer
This buzzer reminds you to remove the
key when you open the driver ’s door with
the ignition key in the “ACC” or “LOCK”
position.
(n) Light reminder buzzer
The buzzer will sound if the headlight
switch is left on and the driver’s door is
opened with the key removed from the
ignition switch.
(o) Warning function of the Sequential Manual Transmission (sequential
manual transmission only)
When driving, if any incorrect operation
that may cause damage to this system is
performed or if the gear is not shifted as
desired by the driver, the warning buzzer
will sound and the gear position indicator
will flash to warn the driver in some
cases. For details, see “(k) Warning
functions” on page 94 in Section 16. CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light)
1. Apply the parking brake.
2. Open either side door. The open door warning light should
come
on.
3. Close the door. The open door warning light should go
off.
4. Turn the ignition key to “ON”, but do not start the engine.
All the service reminder indicators ex-
cept the open door warning light should
come on. The “ABS” and power steer-
ing system warning lights go off after
a few seconds. The SRS warning light
goes off after about 6 seconds.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, have it checked by your Toyota
dealer as soon as possible.
03 07.07

832003 MR2 from Aug. ’03 Prod. (OM17511U)
OPERATION OF INSTRUMENTS AND
CONTROLS
Ignition switch, Transmission and Parking brake
Ignition switch with steering lock84
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sequential manual transmission 85
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual transmission 96
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . .
Parking brake 97
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . .
Cruise control 98
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . .
03 07.07
SECTION 1 7

852003 MR2 from Aug. ’03 Prod. (OM17511U)
The sequential manual transmission is a
6speed forward/reverse transmission.
With the basics of the traditional manual
transmission, the clutch operation and
shifting are controlled electronically. The
system has the following features:
The electronically controlled clutch op-
eration and transmission enables gear
shift by the operation of the selector
lever (or the steering switch) only.
When starting the engine, turn the igni-
tion switch to the “ON” position. While
holding down the brake pedal firmly,
shift the selector lever to the “N” posi-
tion. Make sure that the “N” indicator
in the instrument cluster comes on,
and then start the engine. In case the
selector lever is in a position other
than “N”, or the if the brake pedal is
not held down, the engine cannot be
started.
Sequential manual transmission will
downshift to 2nd or 1st automatically
when the speed is reduced less than
the fixed speed with the shift lever in
“S” position.
To understand this unique system and op-
eration method of the sequential manual
transmission, read this section thoroughly
before driving.
SD16017
The sequential manual transmission has a
shift lock system. This system locks the
selector lever to keep the transmission
gear and the selector lever position in the
same position when the ignition switch is
turned to the “ACC” or “LOCK” position.
However, if the selector lever is locked in
the “S” position, the lever can be moved
to the “+” or “” direction, but the gear
will not be actually shifted. (a) Selector lever
“R”: Reverse
“N”: Neutral and engine starting
“S”: Sequential driving
(normal driving)
“+”: Upshifting
Pull the selector lever to the “+”
direction and release it. Every
time the lever is operated, the
transmission is upshifted 1 step in
the order of 1st 2nd 3rd 
4th 5th 6th gear.
“”: Downshifting
Push the selector lever to the “”
direction and release it. Every
time the lever is operated, the
transmission is downshifted in the
order of 6th 5th 4th 
3rd 2nd 1st gear.
The gear position is displayed on the gear
position indicator. The gear position indica-
tor shows the transmission gear position.
Before starting off, always make sure by
using the gear position indicator that the
gear is engaged in 1st or reverse, then
depress the accelerator pedal.
03 07.07
Sequential manual
transmission

862003 MR2 from Aug. ’03 Prod. (OM17511U)
SB16018
(b) Transmission shift switchesUP:
Upshift switches (Back of the steering
wheel)
Push the upshift switch on the back of the
steering wheel. Every time the switch is
operated, the transmission is shifted up 1
step in the order of 1st 2nd 3rd 
4th 5th 6th gear.
DOWN: Downshift switches (Face of the
steering wheel)
Push the downshift switch on the face of
the steering wheel. Every time the switch
is operated, the transmission is down-
shifted 1 step in the order of 6th 5th
 4th 3rd 2nd 1st gear.
Gear shift from “1st” to “6th” by the steer-
ing switch is possible when the selector
lever is in the “S” position. The gear posi-
tion is displayed on the gear position indi-
cator. The gear position indicator shows
the transmission gear position.
(c) System Operation
When the driver ’s door is opened, the
system is activated, and the motor pump
operates to accumulate pressure. The sys-
tem enters standby mode when the accu-
mulated pressure reaches the specified
level. A motor sound may be heard from
the engine compartment at this time, but
it does not indicate malfunction. The motor
will stop after a certain period of time.
SD16018a
Selector lever
03 07.07

872003 MR2 from Aug. ’03 Prod. (OM17511U)
SB16019a
Transmission shift switches
(d) Upshift and downshift
The sequential manual transmission is not
an automatic transmission (A/T), therefore,
the gears are not shifted automatically. To
shift the transmission, the driver must op-
erate the selector lever to the “+” or “”
direction, or the steering switch with the
selector lever in the “S” position. When
driving, the driver should shift the gear at
the most appropriate timing. As on the
traditional manual transmission vehicles,
releasing the accelerator pedal a little will
help the transmission to upshift smoothly.
Upshift: Pull the selector lever to the “+”
direction and release it (or push the up-
shift switch on the back of the steering
wheel.) Every time the switch or the lever
is operated, the transmission is upshifted
1 step in the order of 1st 2nd 3rd
 4th 5th 6th gear.
Downshift: Push the selector lever to the
“” direction and release it (or push the
downshift switch on the face of the steer-
ing wheel.) Every time the switch or the
lever is operated, the transmission is
downshifted 1 step in the order of 6th 
5th 4th 3rd 2nd 1st gear. In case of operating the selector lever and
switch operation on the steering wheel at
the same time, the selector lever opera-
tion has priority. In case of operating the
two switches of upshifting or downshifting
on the steering wheel at the same time,
it is regarded to operate the switch once.
Also, in case of operating the upshift and
downshift switches on the steering wheel
at the same time, demand is canceled and
no shifting is performed.
To shift down smoothly, the engine
runs fast in some cases. This is done
intentionally by the system and is not
a malfunction.
When the accumulated pressure of the
actuator is consumed due to shifting
operation, and the pressure decreases
to a specified level, the pump motor
starts running again. A motor sound
may be heard from the engine compart-
ment at this time, but it does not indi-
cate malfunction.
When driving down a hill, downshift
and use the engine brakes appropriate-
ly. If necessary, continuous shifting-
down is possible. However, if down-
shifting more than 3 steps continuously,
the gear shifting will take more time.
03 07.07

882003 MR2 from Aug. ’03 Prod. (OM17511U)
When the outside temperature is ex-
tremely low, the gear may not down-
shift from 2nd to 1st until the vehicle
stops.
In case the gear jumps out of position
while driving, the system will shift the
gear where it was before it jumps out.
If operating the selector lever to the
“N” position while driving, and operating
it to the “S” position again, the gear
will be shifted to its most proper posi-
tion in accordance with the speed.
In case the transmission cannot be en-
gaged to a certain gear position during
shifting due to mechanical malfunction,
the system will disengage the gear for
a few seconds, and select the next
gear. Therefore, the vehicle may not
accelerate according to the driver’s
intention.Recommended shifting speeds
For the best compromise between fuel
economy and vehicle performance, you
should upshift or downshift at approxi-
mately the following speeds;
gear km/h (mph)
1 to 2 or 2 to 1 24 (15)
2 to 3 or 3 to 2 40 (25)
3 to 4 or 4 to 3 64 (40)
4 to 5 or 5 to 4 72 (45)
5 to 6 or 6 to 5 81 (50)
Upshifting too soon or downshifting too
late will cause lugging, and possibly ping-
ing. Regularly revving the engine to maxi-
mum speed in each gear will cause ex-
cessive engine wear and high fuel
consumption.
Minimum allowable speeds
Try to keep speed higher than that shown
below. When the speed comes to de-
crease the speed shown below, do down-
shift. gear km/h (mph)3 30 (19)
4 40 (25)
5 50 (31)
6 56 (35)
NOTICE
If driving at the speed lower than that
shown above at each gear position, it
may cause early wear of the clutch.
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
gear km/h (mph)
1 53 (33)
2 88 (55)
3 120 (75)
4 163 (101)
03 07.07

892003 MR2 from Aug. ’03 Prod. (OM17511U)
CAUTION
Be careful when accelerating, up-
shifting, downshifting or braking on
a slippery surface. Sudden accelera-
tion or engine braking could cause
the vehicle to spin or skid.
To drive down a long or steep hill,
reduce your speed and downshift.
Remember, if you ride the brakes
excessively, they may overheat and
fail.
Do not place the selector lever in
the “N” position while driving.
Otherwise the engine brake may not
work, and you may get involved in
an unexpected accident.
Do not apply the parking brake
while driving. Otherwise, it could
cause a skid and you may get in-
volved in an unexpected accident.
NOTICE
The system will not allow shifting
up or down to a gear that would
cause engine overrevving or un-
derrevving. When engine overrev-
ving occurs, a warning buzzer
(short pulse sound) will sound. In
either case, the demand will be can-
celled.
 If frequently driving at low speed
using a high gear position, a warn-
ing buzzer (long pulse sound) will
sound. Such driving will cause the
reduction of clutch life.
 Frequent downshifting (more than 3
positions continuously) causes the
reduction of transmission life.
 Do not drive with your foot on the
brake pedal. Otherwise, it will cause
the “Sequential manual
transmission” warning light to come
on.
(e) Starting off
1. Start the engine as instructed in “How to start the engine” on page 154 in
Section 3. 2. With your foot holding down the brake
pedal, shift the selector lever to the “S”
position properly. When the selector le-
ver is shifted to “S” position, the gear
will be shifted to 1st. On a slippery
surface, it is possible to start off with
the gear in 2nd. To start off with the
gear in 2nd, shift the selector lever
from “N” to “S” position, then operate
the lever to “+” direction. The gear will
be shifted to 2nd. Before starting off,
always make sure that the gear is en-
gaged by the gear position indicator,
then depress the accelerator pedal.
If the gear cannot be engaged to 1st
when the selector lever is shifted from
the “N” to “S” position, the “N” indica-
tor will flash and a warning buzzer
(long pulse sound) will sound. In this
case, the system will retry shifting or
the driver can operate the selector le-
ver to shift, as follows.
The system will retry shifting automat-
ically. This will take some time, noise
may be heard from the gears, and shift
shock may occur. However, they do not
indicate malfunction.
The driver may shift the selector lever
to the “N” position once, then shift to
the “S” position.
03 07.07

902003 MR2 from Aug. ’03 Prod. (OM17511U)
3. Release the parking brake and brakepedal. Depress the accelerator pedal
slowly for smooth starting.
CAUTION
Unlike automatic transmission mod-
els, the sequential manual transmis-
sion models do not creep.
NOTICE
On a slippery surface, it is possible
to start off with the gear in 2nd,
but to protect the clutch, try to
start using the 1st gear whenever
possible.
 If the gear cannot be engaged to
1st when the selector lever is
shifted from the “N” to “S” posi-
tion, try to shift the selector lever
to the “N” position once, then shift
it to “S” position a few seconds
later.
(f) Starting off on an uphill/downhill
—Uphill
1. Apply the parking brake firmly so that the vehicle does not roll backwards. 2. Shift the selector lever to the “S” posi-
tion while holding down the brake pe-
dal. Make sure that the gear position
indicator in the instrumental cluster dis-
plays 1st gear.
3. Release the brake pedal and depress the accelerator pedal gradually, and
when the vehicle starts to move, re-
lease the parking brake and depress
the accelerator pedal to start off.
—Downhill
1. Hold down the brake pedal and shift the selector lever to the “S” position.
Make sure by using the gear position
indicator that the gear is in 1st.
2. Release the brake pedal, and depress the accelerator pedal slowly. Even
though the accelerator pedal is not de-
pressed, when the vehicle speed in-
creases, the clutch will be engaged
and the engine brake will be applied.
CAUTION
Unlike automatic transmission mod-
els, the sequential manual transmis-
sion models will not creep.
NOTICE
Do not hold the vehicle on an uphill
with the accelerator pedal applied.
Doing so may damage the clutch. Al-
ways use the brake pedal or parking
brake.
03 07.07

922003 MR2 from Aug. ’03 Prod. (OM17511U)
If you stop for more than 90 seconds with
the selector lever in the “S” position with-
out holding down the brake pedal while
the engine is running, a warning buzzer
(long pulse sound) will sound, and the “N”
indicator in the instrument cluster will
flash, and the system will automatically
shift the transmission gear to the neutral
gear position.
If the driver ’s door is opened with the
selector lever in the “S” position without
depressing the brake pedal, warning buzz-
er (long pulse sound) will also sound. 10
seconds later, the “N” indicator in the in-
strument cluster will also flash, and the
system will automatically shift the trans-
mission gear to the neutral gear position.
The gear will resume to 1st or 2nd when
the system is operated as follows:
Brake pedal “ON”: The gear position
before the system selected the “N”
position is resumed.
Operate the selector lever to the “+”
direction: Resume to 2nd gear.
Operate the selector lever to the “”
direction: Resume to 1st gear.
Push upshift switch on the steering
wheel: Resume to 2nd gear.
Push downshift switch on the steering
wheel.: Resume to 1st gear.
“S”“N” “S”: Resume to 1st gear.
When starting off again, always confirm
the gear position by the gear position indi-
cator.
CAUTION
Unlike automatic transmission mod-
els, the sequential manual transmis-
sion models do not creep.
When racing the engine, make sure
that the gear position is in the “N”
position by the gear position indica-
tor. In case the accelerator is oper-
ated with the gear in any other
position, the vehicle may move re-
sulting in an unexpected accident.
When you stop the vehicle, hold the
brake pedal down or shift the selec-
tor lever to the “N” position. If the
selector lever is left in the “S”
position without depressing the
brake pedal for more than 90 sec-
onds while stopping, a warning
buzzer (long pulse sound) will
sound, and the “N” position indica-
tor in the instrument cluster will
flash, and the system will automati-
cally shift the transmission gear to
the neutral gear position. If this
happens on a hill, when starting off
the vehicle, the vehicle may move
unexpectedly and cause an acci-
dent.
Do not leave your vehicle unat-
tended while the engine is running.
03 07.07

932003 MR2 from Aug. ’03 Prod. (OM17511U)
When leaving the vehicle, stop the
engine and park the vehicle with
the gear engaged. In case you need
to leave the vehicle with the engine
running, apply the parking brakes
firmly, and shift the selector lever
in the “N” position. When the driv-
er’s door is opened with the selec-
tor lever in the “S” position while
stopping with the engine running,
warning buzzer (long pulse sound)
will sound. 10 seconds later, the
“N” indicator in the instrument
cluster will also flash, and the sys-
tem will automatically shift the
transmission gear to the neutral
gear position. If this happens on a
hill when starting off the vehicle,
the vehicle may move unexpectedly
and cause an accident.NOTICE
Do not hold or stop the vehicle on
a hill with the accelerator pedal ap-
plied. Otherwise, the warning buzz-
er (long pulse sound) will sound,
and in some cases the engine will
stall. It will also cause excessive
damage to the clutch.
 If the selector lever is operated
more than necessary, the system
may not allow operation of the se-
lector lever for a certain period of
time, and the gear may not be
shifted appropriately. Therefore, do
not operate the selector lever if not
necessary.
(i) Parking
Unlike the automatic transmission, the se-
quential manual transmission does not
have a parking position. The vehicle can
be parked with the selector lever in any
position. Apply the parking brake firmly,
and while depressing the brake pedal,
shift the selector lever into the “R” posi-
tion on a level or downhill, and into the
“S(1)” position on an uphill.
SD16020
1: Uphill
2: Level or downhill
To stop the engine:
Check the transmission gear position by
the gear position indicator, then turn the
ignition switch off to stop the engine. Re-
lease the brake pedal after a few sec-
onds. The selector lever will be locked in
the position just before the ignition switch
was turned off.
You can check the gear position by the
gear position indicator within 5 seconds
after turning the ignition switch off.
03 07.07