remote control TOYOTA PRIUS 2001 Service User Guide

NEW MODEL OUTLINE
MAIN EQUIPMENT
182MO23(For U.S.A.)
Glove box Accesory box Multi-box
Front door pocket
Seat back pocket
(Driver's and
passenger seat)
182MO24182MO09
182MO25
Small storage box
Cup holder
(for two caps use)11.839ft3 (by SAE suitcase method)
luggage space is secured.182MO26182MO27182MO28
18
Air Conditioning
An automatic air conditioning has been adopted
in consideration to ease of use.

A clean air filter which removes pollen and
dust is included as a standard fitting for puri-
fying the air inside the cab.

Two air conditioning modes, A/C for eco-
nomical air conditioning and MAX for espe-
cially strong air conditioning, are provided.
Wireless Door Lock Remote Control System
With the wireless door lock remote control system, all the doors can be locked and unlocked by signals emitted
by the transmitter.
Power Window System
A power window system which enables all windows to be raised or lowered with switches has been adopted.
An auto up/down function and jam protection function have been added to the driver's power window.
HV Immobiliser System
HV immobiliser system will not allow the HV system to be started by duplicate key is used. This system
will permit the HV system to be started only when the ID code of the transponder chip impregnated in the
key matches the ID code registered beforehand in the transponder key amplifier.
Theft Deterrent System
When an attempt is made to forcibly enter the vehicle or open the hood or trunk lid without a key, or when
the battery terminals are removed and reconnected, this system sounds the horn and flashes the headlights,
taillights and emergency flashers for about 1 minute to alert the owner. At the same time, it locks all the
doors.
Storage Space
Ample storage space with an emphasis on practicality provided throughout the Prius.
Instrument panel (passenger seat)Seat back pocketFront door pocket
Center console boxLuggage space

BODY ELECTRICAL ± MULTIPLEX COMMUNICATION SYSTEM 142
SYSTEM OPERATION
1. General
The ECUs that pertain to the body electrical system perform the functions and system controls described be-
low.
Gateway ECU
Conversion of data between AVC-LAN and BEAN
Transmission of vehicle information to the display ECU, in order for it to be displayed on multi-informa-
tion display
Body ECU
Power window system control (Front, Rear passenger only)
Door lock control system control
Wireless door lock remote control system control
Theft deferrent system control
Daytime running light system control
Illuminated entry system control
Light auto turn-off system control
Seat belt warning system control
Key reminder system control
Diagnosis
Meter ECU
Meter control
Illumination and flashing control of indicator and warning lights
Sounding control of warning buzzer
Air Conditioning ECU
Air Conditioning control
ECM
Engine control
Diagnosis
Display ECU
Transmission and reception associated with audio and visual functions

BODY ELECTRICAL ± ACCESSORIES
182BE41
RRP DBody
ECUUARTPower
Window
Master
SwitchDoor Control
Switch (Manual)
Door Control
Switch (Key-linked)
169BE10
Key Unlock
Warning SwitchDoor Courtesy
Switch
Door Lock
MotorsBody
ECU
Serial Data Link
Wireless Door
Control Receiver
Horn
RelayHeadlight
RelayTaillight
RelayTransmitter183
DOOR LOCK CONTROL SYSTEM
The door lock control system has the following features:
This system has a ªkey-linked lock and unlockº, ªkey-confine preventionº and ªmanual unlock prohibi-
tionº functions.
A 2-step unlock function is provided to unlock the driver's door by turning the key cylinder first and to
unlock passenger's door by turning it the second time.
The control of this system is effected by the body ECU. The door lock control signal from the driver's door
is transmitted from the power window master switch to the body ECU through the UART (Universal
Asynchronous Receiver Transmitter).
If you unlock using the ignition key from the conditions in which all the doors are locked, the dome light
will be lighted.

System Diagram 
WIRELESS DOOR LOCK REMOTE CONTROL SYSTEM
The wireless door lock remote control system has the following features:
In this system, the wireless door control receiver performs the code identification process and the body
ECU effects the door lock control. Serial data link is provided for communication between the wireless
door control receiver and the body ECU.
A key-holder type transmitter has been adopted, and it contains the following three switches: the door lock
switch, door unlock switch, and panic switch.
A rolling code system, in which the signal configuration changes each time when a signal is transmitted
by the transmitter, has been adopted.
Panic alarm operation has been adopted.
The verification light function has been adopted. When the transmitter is used to lock or unlock the doors,
this function flashes the taillights to inform that the operation has been completed. However, at the time
of unlocking, the dome light will be lighted.

BODY ELECTRICAL ± ACCESSORIES187
Condition (2)
When the doors, engine hood, and luggage compartment door are all closed and locked, and 30 seconds
have elapsed.
Condition (3)
When one of the doors, engine hood, or luggage compartment door is changed from ªcloseº to ªopenº.
When one of the doors, engine hood, or luggage compartment door is changed from ªlockº to ªunlockº.
When the ignition key is inserted in the ignition key cylinder.
When a terminal is disconnected from the battery and re-connected.
Alert State: a state in which attempted theft can be detected
The system transfers to the alarm state if any one of the conditions (4) listed below is met, or to the non-alert
state if any one of the conditions (5) is met.
Condition (4)
Any door, engine hood, or luggage compartment door is opened.
The ignition key or the wireless door lock remote control system other than the transmitter is used for
unlocking.
The luggage compartment door is opened with something other than the ignition key.
The engine hood is opened.
A terminal is disconnected from the battery and re-connected.
The wiring harness is directly connected as if to turn the ignition switch ON.
Condition (5)
The ignition key is used to unlock the doors or the luggage compartment door.
The transmitter of the wireless door lock remote control system is used to unlock the doors.
The ignition key is inserted in the ignition key cylinder and turned until the ignition switch is ON.
Alarm State: a state in which attempted theft can be detected
When an attempted theft is detected, the system sounds the vehicle's horn and the security horn, flashes
the headlights, taillights, and hazard lights, and illuminates the interior light to alert the people in the area.
If any one of the doors is unlocked, and the ignition key is not inserted in the ignition key cylinder, the
system forcefully locks the doors once.
The system transfers to the alert state if the condition (6) described below is met, or, when the system is
in the alarm state, it transfers to the non-alert state if any one of the conditions (5) described above is met.
At this time, the taillights are illuminated for 2 seconds to inform the driver that an attempted theft has been
detected.
Condition (6)
After approximately 60 seconds of the alarm time have elapsed.

 No key in ignition key cylinder.
 All doors and luggage compartment closed
 All doors unlocked
 Engine hood open
Lock and unlock by or remote control 3
times.
Lock and unlock the driver's door knob 3
times.
Open the driver's door.
After 2 sec., forced lock functions once.
Unlock the driver's door knob.
Close and open the driver's door 2 times.
Lock and unlock the driver's door knob once.
Afer 2 sec., forced lock functions once.
System without passive mode is set.System with passive mode is set.
Within
30 secs.
Within
20 secs.
HINT:

Initially (when shipping), system without passive mode is set..

Any input or output other than the above shall be regarded as invalid.(Start again from the beginning).
Input to the vehicle
Output from the vehicle
Close and open the driver's door 3, 4 or 5
times.
Lock and unlock the driver's door knob once.
After 2 sec., forced lock functions once.
Within
2 secs.
Within
2 secs. BE±74
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
2001 PRIUS (RM778U)
4. CHANGING METHOD OF PASSIVE MODE
(ON or OFF)

BE0IM±13
Make the vehicle in the initialized condition:
The initialized condition is the condition when the following conditions are satisfied.
(1) Key plate has not been inserted in the ignition key cylinder.
(2) All the doors are closed. (Door warning light is off.)
(3) All the doors are locked.
Under the standard operation, when repeating the operation of UNLOCK and LOCK switch
3 times or more alternately, check the UNLOCK±LOCK operation from 3rd time onward.

Following procedures are standard operation.
(1) Keep about 1 M away to the right direction from the outside handle of a driver's seat.
(2) Face the transmitter toward the vehicle and press one of transmitter switches for about 1 sec.
Normal


Operative distance may differ according to
an operator, the way of holding the transmitter
or position.

Because weak electric wave is used, when
there is strong wave or noise in the used
frequency ,operation distance might be
shortened.
NoYe s
Only wireless function (Remote control) will not operate.
(If a new transmitter or a transmitter of the same type that works properly with the vehicle is not available.)
Basic function check: BE±78
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
2001 PRIUS (RM778U)
PRE±CHECK

BE0OJ±12
I12019
Dry cell battery (1.5 V x 2)
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±83
2001 PRIUS (RM778U)
INSPECTION
1. INSPECT WIRELESS DOOR LOCK TRANSMITTER
OPERATION
HINT:
Refer to ºWireless door lock control receiver and transmitter re-
placementº on page BE±87.
(a) Using a screwdriver, remove and cover.
(b) Remove the battery (lithium battery).
(c) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery can not be obtained, connect 2
new 1.5 V batteries in series, connect the battery (+) to the bat-
tery receptacle side terminal and battery (±) to the bottom termi-
nal, then apply 3 V voltage to the transmitter.
(d) In the location where is approx. 1 M away from driver's
outside handle in the right direction, and check the trans-
mitter operation when pressing transmission switch on
the surface of the transmitter body.
Standard:
Remote control of vehicle door lock can be operated.
HINT:

The minimum operation distance differs according to op-
erator, the way of holding, and location.

As weak wave is used, operation distance might be short-
ened when noise is detected in strong wave or used fre-
quency.
(e) Install the battery (lithium battery).
(f) Install a cover so that rubber cover is not distorted or
slipped off.