display TOYOTA PRIUS 2021 (in English) Owner's Manual

35
CHANGING PRE-COLLISION ALERT TIMING
DISABLING PRE-COLLISION SYSTEM (PCS)
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting. Each time it is pressed, the response to
the PCS warning timing changes as shown above.
(4) Press “” to go back to the menu.
Note: PCS is enabled each time the engine switch is turned to Ignition On.
The system can be disabled/enabled and the alert timing of the system can be
changed. (Alert timing only, brake operation remains the same).
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting (ON/OFF).
(4) Press “” to go back to the menu.
Note: The system is enabled each time the power switch is turned to ON mode.
Refer to the Toyota Owner’s Manual for additional information on PCS operation,
settings adjustments, limitations, and precautions before attempting to use it.
OVERVIEW
FEATURES
& OPERATIONS
TOYOTA
SAFETY
SENSE
SAFETY
& EMERGENCY
FEATURES
Far
Middle(default)
Near
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 35126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 356/17/20 10:09 AM6/17/20 10:09 AM

37
LANE DEPARTURE ALERT
LDA function display
Operation display of steering wheel operation support
LDA indicator
Steering control indicator and operation display (steering assist function)
Lane markers/road edge
(2)(1)
Lane Departure Alert (LDA) indicator flashes orange when operating.
The LDA function “” displays when the Multi-Information Display (MID) is
switched to the driving assist system information screen.
(1) The system displays solid white lines on the LDA indicator when visible lane
markers or the road are detected. A side flashes orange to alert the driver when the
vehicle deviates from its lane.
(2) The system displays outlines on the LDA indicator when lane markers or the road
are not detected or the function is temporarily canceled.
Note: When operation conditions are no longer met, a function may be
temporarily canceled. However, when the operation conditions are met again,
operation of the function is automatically restored. For example, LDA may not
function on the side(s) where white/yellow lines are not detectable.
Refer to the Toyota Owner’s Manual for additional information on LDA operation,
settings adjustments, limitations, and precautions before attempting to use it.
OVERVIEW
FEATURES
& OPERATIONS
TOYOTA
SAFETY
SENSE
SAFETY
& EMERGENCY
FEATURES
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 37126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 376/17/20 10:09 AM6/17/20 10:09 AM

38
ADJUSTING LDA ALERT SENSITIVITY
DISABLING STEERING ASSIST
The driver can adjust the sensitivity of the LDA (warning) function from the
Multi-Information Display (MID) customization screen.
High - Is designed to warn approximately before the front
tire crosses the lane marker.
Normal - Is designed to warn approximately when the front
tire crosses the lane marker.
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting (High/Normal).
(4) Press “” to go back to the menu.
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting (ON/OFF).
(4) Press “” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
TOYOTA SAFETY SENSE™
SWAY WARNING SYSTEM
SWS is a function of LDA and is designed to detect swaying based on the vehicle
location in the lane and the driver’s steering wheel operation. To help prevent
swaying, the system alerts the driver using a buzzer sound and a warning displays
in the MID.
Continuous lane deviations from swaying.
Gentle swaying from driver’sinattentiveness.
Acute steering wheel operation after the number of operations decrease due to driver’s inattentiveness.
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 38126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 386/17/20 10:09 AM6/17/20 10:09 AM

39
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting. Each time it is pressed, the response to
the sway warning timing changes.
(4) Press “” to go back to the menu.
Refer to the Toyota Owner’s Manual for additional information on LDA operation,
settings adjustments, limitations, and precautions before attempting to use it.
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting (ON/OFF).
(4) Press “” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
ADJUSTING SWAY ALERT SENSITIVITY
DISABLING LDA SWAY WARNING ALERT
When enabled, the LTA system’s lane centering function is designed to
automatically provide assistance to help keep the vehicle in the center of the lane
when Full-Speed Range DRCC is set.
Lane Tracing Assist (LTA)
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 39126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 396/17/20 10:09 AM6/17/20 10:09 AM

40
TOYOTA SAFETY SENSE™
TURNING THE LTA SYSTEM ON/OFF
Press the LTA switch to turn the LTA system on. Depress again to turn it off.
Note: Operation of the LTA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
Refer to the Toyota Owner’s Manual for additional information on LTA operation,
settings adjustments, limitations, and precautions before attempting to use it.
LANE TRACING ASSIST
LTA function display
Lane Tracing Assist (LTA) indicator flashes orange when operating.
Operation display of steering wheel operation support
LTA indicator
Steering control indicator and operation display (steering assist function)
Lane markers
Follow-up cruising display
(2)(1)
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 40126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 406/17/20 10:09 AM6/17/20 10:09 AM

41
The LTA function “” displays when the Multi-Information Display (MID) is
switched to the driving assist system information screen.
(1) The system displays solid white lines on the LTA indicator when visible lane
markers on the road are detected. A side flashes orange to alert the driver when the
vehicle deviates from its lane.
(2) The system displays outlines on the LTA indicator when lane markers on the road
are not detected or the function is temporarily canceled.
Note: When operation conditions are no longer met, a function may be
temporarily canceled. However, when the operation conditions are met again,
operation of the function is automatically restored. For example, LTA may not
function on the side(s) where white/yellow lines are not detectable.
Refer to the Toyota Owner’s Manual for additional information on LTA operation,
settings adjustments, limitations, and precautions before attempting to use it.
ADJUSTING LTA ALERT SENSITIVITY
DISABLING STEERING ASSIST
LANE TRACING ASSIST (CONTINUED)
The driver can adjust the sensitivity of the LTA (warning) function from the
Multi-Information Display (MID) customization screen.
High - Is designed to warn approximately before the front
tire crosses the lane marker.
Normal - Is designed to warn approximately when the front
tire crosses the lane marker.
OVERVIEW
FEATURES
& OPERATIONS
TOYOTA
SAFETY
SENSE
SAFETY
& EMERGENCY
FEATURES
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting (ON/OFF).
(4) Press “” to go back to the menu.
Note: Operation of the LTA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” and then press “.” The setting
screen is displayed.
(3) Press “” to select the desired setting (High/Normal).
(4) Press “” to go back to the menu.
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 41126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 416/17/20 10:09 AM6/17/20 10:09 AM

42
TOYOTA SAFETY SENSE™
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” and then press “.” The
setting screen is displayed.
(3) Press “ ” switches and select the “On/Off” and then press “” to select the
desired setting.
(4) Press “” to go back to the menu.
Note: Operation of the LTA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
Refer to the Toyota Owner’s Manual for additional information on LTA operation,
settings adjustments, limitations, and precautions before attempting to use it.
DISABLING LANE CENTERING FUNCTION
LANE CENTERING
The lane centering function is linked with Full-Speed Range Dynamic Radar Cruise
Control (DRCC) and provides the required assistance by operating the steering
wheel to keep the vehicle in its current lane.
When dynamic radar cruise control with full-speed range is not operating, the lane
centering function does not operate.
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 42126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 426/17/20 10:09 AM6/17/20 10:09 AM

43
Full-Speed Range Dynamic Radar Cruise Control
(DRCC)
Full-Speed Range DRCC helps maintain a pre-set distance to a preceding vehicle
when the preceding vehicle is traveling at a lower speed. This mode is always
selected first when the cruise control button is depressed. Constant speed cruise
control mode is also available. Full-Speed Range DRCC is designed to function at
speeds between 0 to approximately 110 MPH and is intended for highway use.
OVERVIEW
FEATURES
& OPERATIONS
TOYOTA
SAFETY
SENSE
SAFETY
& EMERGENCY
FEATURES
TURNING SYSTEM ON/OFF
ADJUSTING SET SPEED
* The speed control may also be canceled by depressing the brake pedal.
Refer to page 45 for switching to Constant Speed (Cruise) Control Mode.
Vehicle will cruise at a set speed, decelerate to maintain selected distance from a
slower vehicle traveling in front and accelerate back up to the selected speed if the
vehicle in front changes lanes or speeds up.
(1) Push the ON-OFF button. The “RADAR READY” and “” indicator will come
on the Multi-Information Display (MID).
(2) Push the lever down to SET speed, push it up to Resume and pull it or depress
brake to Cancel the speed control.
(3) Push up to increase the set speed, push down to decrease (1 mph [1.6 km/h] or
1 km/h [0.6 mph] increments).
(3)
(1)
Push once: On Push again: Off
(2)
Decrease speed
Increase speed
Cancel*
Resume
Set
Display
Set speed
Dynamic Radar Cruise Controlvehicle-to-vehicle distance button
Cruise control switch
Indicators
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 43126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 436/17/20 12:36 PM6/17/20 12:36 PM

45
SWITCHING TO CONSTANT SPEED (CRUISE) CONTROL MODE
SETTING CONSTANT SPEED (CRUISE) CONTROL
Note: When your vehicle is too close to a vehicle ahead, and sufficient automatic
deceleration via the cruise control is not possible, the display will flash and the
buzzer will sound to alert the driver. An example of this would be if another driver
cuts in front of you while you are following a vehicle. Depress the brake pedal to
ensure an appropriate vehicle-to-vehicle distance.
If you are already using DRCC “,” push ON-OFF button to turn the system off
first, then push and hold ON-OFF button for at least 1.5 seconds to switch.
Note: When the engine is turned off, it will automatically default to DRCC.
(3) Acceleration when there are no longer any preceding vehicles driving
slower than the set speed
The system accelerates until the set speed is reached. The system then
returns to constant speed cruising.
To adjust speed or cancel, see steps (2) and (3) of ADJUSTING SET SPEED on
page 43.
Refer to the Toyota Owner’s Manual for additional information on DRCC operation,
settings adjustments, limitations, and precautions before attempting to use it.
ADJUSTING DISTANCE (CONTINUED)
OVERVIEW
FEATURES
& OPERATIONS
TOYOTA
SAFETY
SENSE
SAFETY
& EMERGENCY
FEATURES
1.5 seconds
Set
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 45126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 456/17/20 10:09 AM6/17/20 10:09 AM

47
OVERVIEW
FEATURES
& OPERATIONS
TOYOTA
SAFETY
SENSE
SAFETY
& EMERGENCY
FEATURES
Road Sign Assist (RSA)
Road Sign Assist is designed to help ensure drivers are kept informed. The RSA
system recognizes specific road signs using a forward-facing camera and/or
navigation system to provide information to the driver via a Multi-information Display
(MID). If the system judges that the vehicle is being driven over the speed limit, or
performing actions prohibited by other support types of road signs, it notifies the
driver using a notification display and notification buzzer.
RSA DISPLAY
SUPPORTED TYPES OF ROAD SIGNS
SETTING RSA
When the driving assist system
information is selected, a maximum of
2 signs can be displayed.
Speed limitStop
Do Not EnterYield
When a tab other than the driving assist
system information is selected, the
following types of road signs will be
displayed.
• Speed limit sign
• Do Not Enter sign (when notification
is necessary)
(1) Press “ ” switches and select “” from the Multi-Information Display (MID).
(2) Press “ ” switches and select the “” setting function and then press “.”
(3) Press “” each time to change the setting.
(4) Press “” to go back to the menu.
Note: If the engine switch was last turned off while a speed limit sign was
displayed on the multi-information display, the same sign displays again when
the engine switch is turned back ON.
Refer to the Toyota Owner’s Manual for additional information on RSA operation,
settings adjustments, limitations, and precautions before attempting to use it.
126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 47126899_MY21_Prius_QRG_V2_ML_0614_R1.indd 476/17/20 10:09 AM6/17/20 10:09 AM