door lock TOYOTA RAV4 1996 Service Manual Online

DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST (RAV4)
OFF9 & 11
DOWN10 & 11
Unlocked
UP4, 5 & 11; 9 & 10
OFF4, 5, 9 & 11
DOWN4, 5 & 9; 7, 10 & 11
Right Rear Switch
Locked
UP10 & 13
OFF13 & 14
DOWN10 & 14
Unlocked
UP4, 5 & 14; 10 & 13
OFF4, 5, 13 & 14
DOWN4, 5 & 13; 10 & 14
(1)See Fig. 7 .
Application & Switch Position(1) Terminals No.
2-Door
Driver's Switch
Locked & Unlocked
UP3 & 5; 4 & 6
OFF3, 4 & 5
DOWN3 & 4; 5 & 6
Passenger's Switch
Locked
UP12 & 13
OFF12 & 14
DOWN13 & 14
Unlocked
UP3 & 14; 12 & 13
OFF3, 12 & 14
DOWN3 & 12; 13 & 14
4-Door
Driver's Switch
Locked & Unlocked
UP1 & 3; 2, 4 & 5
OFF1, 2, 4 & 5
DOWN2 & 3; 1, 4 & 5

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:35 AMPage 6 © 2005 Mitchell Repair Information Company, LLC.

DRIVER'S POWER WINDOW SWITCH CONTINUITY TEST (SIENNA & TUNDRA)
Passenger's Switch
Locked
UP7 & 10
OFF7 & 8
DOWN8 & 10
Unlocked
UP4, 5 & 8; 7 & 10
OFF4, 5, 7 & 8
DOWN4, 5 & 7; 8 & 10
Left Rear Switch
Locked
UP9 & 10
OFF9 & 11
DOWN10 & 11
Unlocked
UP4, 5 & 11; 9 & 10
OFF4, 5, 9 & 10
DOWN4, 5 & 9; 10 & 11
Right Rear Switch
Locked
UP10 & 13
OFF13 & 14
DOWN10 & 14
Unlocked
UP4, 5 & 14; 10 & 13
OFF4, 5, 13 & 14
DOWN4, 5 & 13; 10 & 14
(1)For RAV4 (2-door) master switch terminal locations, see Fig. 6 . For RAV4 (4-door) master switch
terminal locations, see Fig. 7
.
Application & Switch Position(1) Terminals No.
Driver's Switch
Locked & Unlocked
UP1 & 4; 3 & 9
OFF1, 3 & 4
DOWN1 & 3; 4 & 9
Passenger's Switch
Locked
UP8 & 9

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:35 AMPage 7 © 2005 Mitchell Repair Information Company, LLC.

4Runner
1. Remove master switch and disconnect 14-pin connector. Connect jumper wire between 12-volt battery
positive terminal and master switch terminals No. 3 and 10. Connect another jumper between battery
negative terminal and master switch terminal No. 4.
2. Measure voltage by backprobing between specified terminals with driver's power window switch in
specified position. See POWER WINDOW MASTER SWITCH VOLTAGE TEST (4RUNNER)

table. Voltage should be 10-14 volts. If voltage is not as specified, replace power window switch. If
voltage is as specified, switch is okay.
POWER WINDOW MASTER SWITCH VOLTAGE TEST (4RUNNER)
POWER WINDOW SWITCH CONTINUITY TEST (BACK DOOR/TAILGATE)
4Runner
Using an ohmmeter, check continuity between specified terminals with back door/tailgate power window switch
in specified position. See POWER WINDOW SWITCH CONTINUITY TEST (4RUNNER
- BACK
DOOR/TAILGATE) table. See Fig. 13 . If continuity does not exist at specified terminals, replace appropriate
power window switch.
POWER WINDOW SWITCH CONTINUITY TEST (4RUNNER - BACK DOOR/TAILGATE)
DOWN13 & 14
(1)For terminal location, see Fig. 7 .
Application & Switch Position(1) Terminals No.
Driver's Switch (Locked & Unlocked)
UP1 & 2
DOWN1 & 2
Passenger's Switch (Locked & Unlocked)
UP7 & 8
DOWN7 & 8
Left Rear Switch (Locked & Unlocked)
UP9 & 11
DOWN9 & 11
Right Rear Switch (Locked & Unlocked)
UP13 & 14
DOWN13 & 14
(1)For terminal location, see Fig. 7 .
Application & Position(1) Terminals No.
UP2 & 6
OFFNone

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:35 AMPage 11 © 2005 Mitchell Repair Information Company, LLC.

Motor should operate in opposite direction. If motor does not test as specified, replace motor.
POWER WINDOW LOCK SWITCH
Tailgate Door (4Runner)
Switch Continuity Test

Disconnect power window lock switch Black 10-pin connector, located on left side of instrument panel.
Using an ohmmeter, check continuity between terminals No. 7 (White/Black wire) and No. 10
(Blue/White wire) with lock switch in UNLOCK position. See Fig. 13
. Continuity should be present.
With lock switch in LOCK position, continuity should not be present. If continuity is not as specified,
replace switch.
Switch Illumination Circuit Test

Check continuity between power window lock switch terminals No. 2 (Green wire) and No. 3
(Green/White wire). Continuity should be present with power window lock switch in LOCK or UNLOCK
position. If continuity is not as specified, replace power window lock switch.
POWER WINDOW LIMIT SWITCH
Tailgate Door (4Runner)
Disconnect power window limit switch 2-pin connector, located on left side of tailgate door, behind trim panel.
Using an ohmmeter, check continuity between terminals No. 1 (Red/Blue wire) and No. 2 (White/Black wire)
with switch in ON position. Continuity should exist. With switch in OFF position, continuity should not exist. I
f
continuity is not as specified, replace switch.
CONNECTOR VIEWS
Use the following connector views for diagnostic pin point tests in TROUBLE SHOOTING , COMPONENT
TESTS and CIRCUIT TESTS . See Fig. 4-Fig. 13.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:35 AMPage 15 © 2005 Mitchell Repair Information Company, LLC.

POWER WINDOW MASTER SWITCH ILLUMINATION TEST
Land Cruiser & RAV4 (4-Door)
Disconnect power window master switch 14-pin connector. Connect jumper wire from 12-volt battery positive
terminal to master switch connector terminals No. 3 and 10. Connect another jumper wire from negative battery
terminal to master switch connector terminal No. 4. Ensure all switch lights illuminate. If operation is not as
specified, replace power window master switch.
RAV4 (2-Door)
Disconnect power window master switch 14-pin connector. Connect jumper wire from 12-volt battery positive
terminal to master switch connector terminals No. 6 and 13. Connect another jumper wire from negative battery
terminal to master switch connector terminal No. 3. Ensure all switch lights illuminate. If operation is not as
specified, replace power window master switch.
Sienna
Disconnect power window master switch 14-pin connector. Place window lock switch in UNLOCK position.
Connect jumper wire from 12-volt battery positive terminal to master switch connector terminal No. 9. Connect
another jumper wire from negative battery terminal to master switch connector terminal No. 1. Ensure all switch
lights illuminate. Place window lock switch in LOCK position and ensure passenger power window switches do
not illuminate. If operation is not as specified, replace power window master switch.
POWER WINDOW SWITCH POWER SUPPLY TEST
Sienna, Tundra & 4Runner
Disconnect power window switch connector. Measure battery voltage between appropriate power window
switch harness connector terminal and ground. See POWER WINDOW SWITCH POWER SUPPLY TEST

table. With ignition switch in ON position, voltage should be 10-14 volts. If voltage is not as specified, repair
open in affected circuit.
POWER WINDOW SWITCH POWER SUPPLY TEST NOTE: Diagnostic procedures for integration relay circuit is not available.
NOTE: Testing for Land Cruiser, RAV4 and Tacoma is not available.
Application & SwitchConditionTerminal No.
Sienna
Power Window Master Switch (1)
(2) Ignition Switch In ACC Or LOCK Position7
Ignition Switch In ON Position7
Rear Quarter Power Window Switch (3)
(2) Ignition Switch In ACC Or LOCK Position3

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:35 AMPage 22 © 2005 Mitchell Repair Information Company, LLC.

POWER WINDOW SWITCH GROUND TEST
Disconnect power window switch connector. Check for continuity between appropriate power window switch
harness connector terminal and ground. See POWER WINDOW SWITCH GROUND TEST
table.
Continuity should be present at all times. If continuity is not present, repair open in ground circuit.
POWER WINDOW SWITCH GROUND TEST
Ignition Switch In ON Position3
Tundra
Driver Power Window Master Switch (1)
(2) Ignition Switch In ACC Or LOCK Position9
Ignition Switch In ON Position9
Passenger Power Window Switch (4)
(2) Ignition Switch In ACC Or LOCK Position4
Ignition Switch In ON Position4
4Runner
Driver Power Window Master Switch (5)
(2) Ignition Switch In ACC Or LOCK Position10
Ignition Switch In ON Position10
Constant3
Passenger Power Window Switch (6)
Constant7
(1)For switch terminal location, see Fig. 9 .
(2)Voltage will be present for up to 45 seconds after ignition switch is turned to OFF position, or until
driver or passenger door is opened.
(3)For switch terminal location, see Fig. 11 .
(4)For switch terminal location, see Fig. 12 .
(5)For switch terminal location, see Fig. 7 .
(6)For switch terminal location, see Fig. 8 .
NOTE: Testing for Land Cruiser, Tacoma and RAV4 is not available.
Application & SwitchTerminals No.
Sienna
Driver Power Window Master Switch (1) 1
Rear Quarter Power Window Switch (2) 6 & 9
Tundra
Driver Power Window Master Switch (1) 1

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Power Windows - Trucks
Microsoft
Sunday, November 22, 2009 10:59:35 AMPage 23 © 2005 Mitchell Repair Information Company, LLC.

Fig. 10: Rear Wiper Relay Terminals (Celica)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
ModelLocation
CelicaInside Back Door, At Rear Wiper Motor
Land Cruiser, Lexus LX470 &
4RunnerInside Back Door, To Left Of Motor
SiennaUnder Passenger Front Seat
RAV4Instrument Panel Fuse Block

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems
Microsoft
Sunday, November 22, 2009 11:01:20 AMPage 15 © 2005 Mitchell Repair Information Company, LLC.

Remove wiper arm. Remove back door assist grip. Remove pull strap. Remove center garnish above rear door
window by prying along window edge. Remove side garnish on each side of window by pulling inward to
release clips. Pull rear door trim panel outward and remove. Disconnect rear wiper motor connector and remove
bolts attaching rear wiper motor and linkage to rear door.
Removal (4Runner)
Remove back door trim panel. Remove plate and back door glass run channel. Remove outer weatherstrip and
remove rear window. Remove wiper arm and wiper shaft nut on outside of door. Disconnect electrical
connector, remove 3 bolts and remove wiper motor assembly.
Installation (All Models)
To install, reverse removal procedure. Adjust wiper blades to appropriate position. See ADJUSTMENTS .
REAR WIPER SWITCH
Removal & Installation
Switch is integral part of wiper switch mounted to combination switch on steering column. See FRONT
WIPER SWITCH .
STEERING WHEEL
Removal
1. Ensure front wheels are in straight-ahead position. Place ignition switch in LOCK position and remove
key. Disconnect negative battery cable. Remove 2 screw covers from outer sides of steering wheel. Using
Torx Wrench (T30), loosen air bag pad retaining Torx screws until screw heads are snug against screw
case. See Fig. 15
.
2. Carefully pull air bag pad away from steering wheel enough to unlock and disconnect air bag electrical
connector. DO NOT pull on electrical connector or wiring. Store air bag pad aside with pad facing
upward.
3. Remove steering wheel lock nut and washer from steering shaft. Make alignment mark on steering shaft
and steering wheel for installation reference. Using appropriate steering wheel puller, pull steering wheel
from shaft while guiding spiral cable wire through steering wheel opening.
Installation
1. Ensure front wheels are in straight-ahead position. Connect and install spiral cable to combination switch.
Turn spiral cable counterclockwise by hand until it is hard to turn. Turn spiral cable clockwise about 2
1/2-3 turns and align Red mark at bottom with opening.
2. Guide spiral cable through steering wheel opening while installing steering wheel to shaft. Align
reference marks on steering shaft and steering wheel. Install steering wheel lock nut and washer. Tighten
steering wheel lock nut to 25 ft. lbs. (34 N.m).
3. Connect air bag electrical connector and snap down connector lock. Before installing air bag pad, ensure
Torx screws are retracted and snu
g against screw case. See Fig. 15.

1999 Toyota RAV4
1999-2000 ACCESSORIES & EQUIPMENT Wiper/Washer Systems
Microsoft
Sunday, November 22, 2009 11:01:20 AMPage 23 © 2005 Mitchell Repair Information Company, LLC.

Fig. 22: Power Distribution Circuit (2 of 2)
POWER DOOR LOCKS

1999 Toyota RAV4
1999 System Wiring Diagrams Toyota - RAV4
Microsoft
Sunday, November 22, 2009 10:50:58 AMPage 45 © 2005 Mitchell Repair Information Company, LLC.

Fig. 23: Power Door Lock Circuit
POWER MIRRORS

1999 Toyota RAV4
1999 System Wiring Diagrams Toyota - RAV4
Microsoft
Sunday, November 22, 2009 10:50:58 AMPage 47 © 2005 Mitchell Repair Information Company, LLC.