airbag TOYOTA RAV4 2006 Service Owner's Manual

SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEMRS–21
RS
PARTS LOCATION
C123528E03

RS–22SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEM
RS
C128667E03

SUPPLEMENTAL RESTRAINT SYSTEM – AIRBAG SYSTEMRS–23
RS
C128668E01

SUPPLEMENTAL RESTRAINT SYSTEM – SIDE AIRBAG SENSORRS–383
RS
REMOVAL
CAUTION:
Be sure to read the precautionary notices concerning the
SRS airbag system before servicing it (see page RS-1).
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.
2. REMOVE FRONT DOOR SCUFF PLATE LH (See page
IR-26)
3. REMOVE REAR DOOR SCUFF PLATE LH (See page
IR-57)
4. REMOVE CENTER PILLAR GARNISH LOWER LH
(See page SB-27)
5. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH
(a) Disconnect the connector.
(b) Remove the bolt and sensor.
B127915E01

RS–384SUPPLEMENTAL RESTRAINT SYSTEM – SIDE AIRBAG SENSOR
RS
INSTALLATION
HINT:
• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
CAUTION:
Be sure to read the precautionary notices concerning the
SRS airbag system before servicing it (see page RS-1).
1. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH
(a) Install the sensor with the bolt.
Torque: 9.0 N*m (92 kgf*cm, 82 in.*lbf)
NOTICE:
• If the airbag sensor has been dropped, or
there are any cracks, dents or other defects in
the case, bracket or connector, replace it with
a new one.
• When installing the airbag sensor, be careful
that the SRS wiring does not interfere with
other parts and that it is not pinched between
other parts.
(b) Check that there is no looseness in the installation
parts of the sensor.
(c) Connect the connector.
2. INSTALL CENTER PILLAR GARNISH LOWER LH
(See page SB-31)
3. INSTALL REAR DOOR SCUFF PLATE LH (See page
IR-57)
4. INSTALL FRONT DOOR SCUFF PLATE LH (See page
IR-59)
5. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
6. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light (see page RS-34).
B127915E01

SEAT BELT – SEAT BELT WARNING SYSTEMSB–3
SB
SYSTEM DESCRIPTION
1. DRIVER SEAT BELT WARNING LIGHT
(a) When the driver seat belt is not fastened with the
ignition switch ON, the driver seat belt warning light
on the combination meter comes on to inform the
driver. The center airbag sensor detects the driver
seat belt status and sends signals to the
combination meter through the CAN bus line.
2. PASSENGER SEAT BELT WARNING LIGHT
(a) for Automatic air conditioning system:
When the passenger seat belt is not fastened with
the ignition switch ON and the passenger seat
occupied, check that the passenger seat belt
warning light on the heater control panel display
blinks. The combination meter detects the
passenger seat belt status and whether the
passenger seat is occupied.
(b) for Manual air conditioning system:
When the passenger seat belt is not fastened with
the ignition switch ON and the passenger seat
occupied, check that the passenger seat belt
warning light on the clock panel blinks. The
combination meter detects the passenger seat belt
status and whether the passenger seat is occupied.

SB–4SEAT BELT – SEAT BELT WARNING SYSTEM
SB
HOW TO PROCEED WITH
TROUBLESHOOTING
HINT:
• Use these procedures to troubleshoot the seat belt
warning system.
• *: Use the intelligent tester.
NEXT
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery
before proceeding.
NEXT
(a) Use the intelligent tester to check if the airbag system is
functioning normally.
Result
B
A
(a) Use the intelligent tester to check if the occupant
classification system is functioning normally.
Result
B
A
1VEHICLE BROUGHT TO WORKSHOP
2INSPECT BATTERY VOLTAGE
3CHECK FUNCTION OF AIRBAG SYSTEM*
Result Proceed to
DTC is not output A
DTC is output B
GO TO AIRBAG SYSTEM
4CHECK FUNCTION OF OCCUPANT CLASSIFICATION SYSTEM*
Result Proceed to
DTC is not output A
DTC is output B
GO TO OCCUPANT CLASSIFICATION
SYSTEM

ES–4342AZ-FE ENGINE CONTROL SYSTEM – ACCELERATOR PEDAL ROD
ES
REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.
2. REMOVE ACCELERATOR PEDAL ROD
(a) Disconnect the accelerator pedal position sensor
connector.
(b) Remove the 2 bolts and accelerator pedal rod.
INSTALLATION
1. INSTALL ACCELERATOR PEDAL ROD
(a) Install the accelerator pedal rod with the 2 bolts.
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
(b) Connect the accelerator pedal position sensor
connector.
2. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
A124549
A124549

IP–4INSTRUMENT PANEL – UPPER INSTRUMENT PANEL
IP
REMOVAL
1. TABLE OF BOLT, SCREW AND NUT
HINT:
All bolts, screws and nuts relevant to installing and
removing the instrument panel are shown along with
their alphabet codes in the table below.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.
3. REMOVE INSTRUMENT CLUSTER FINISH PANEL
SUB-ASSEMBLY
(a) Using a screwdriver, detach the 4 clips, 6 claws and
remove the instrument cluster finish panel.
HINT:
Tape the screwdriver tip before use.
B129998E05
B129872

IP–6INSTRUMENT PANEL – UPPER INSTRUMENT PANEL
IP
8. REMOVE INSTRUMENT PANEL REGISTER
ASSEMBLY CENTER
(a) Using a screwdriver, detach the 5 clips and remove
the instrument panel register.
HINT:
Tape the screwdriver tip before use.
9. REMOVE GLOVE COMPARTMENT DOOR
ASSEMBLY (See page IP-20)
10. REMOVE FRONT PILLAR GARNISH LH (See page IR-
27)
11. REMOVE FRONT PILLAR GARNISH RH (See page IR-
28)
12. REMOVE UPPER INSTRUMENT PANEL
(a) Remove the 2 bolts from the passenger airbag.
(b) Disconnect the passenger airbag connector.
(c) Remove the 2 bolts and 2 screws.
(d) Disconnect the connectors and clamps.
(e) Detach the 6 clips and 5 claws and remove the
instrument panel.
B129890
B129886
B129870