power steering TOYOTA RAV4 2006 Service Service Manual

PS–32POWER STEERING – ELECTRONIC POWER STEERING SYSTEM
PS
DESCRIPTION
When a problem occurs in the system, the power source relay circuit is shut off to stop the power assist.
WIRING DIAGRAM
INSPECTION PROCEDURE
(a) Connect the intelligent tester (with CAN VIM) to the
DLC3.
(b) Turn the ignition switch ON.
(c) Select the item "PIG SUPPLY" in the DATA LIST and
read the value displayed on the intelligent tester.
Power steering ECU
OK
NG
DTC C1552/22 PIG Power Supply Voltage Malfunction
DTC No. DTC Detection Condition Trouble Area
C1552/22 PIG power source circuit malfunction inside
ECU• PIG power source circuit
• Power steering ECU
1READ VALUE OF INTELLIGENT TESTER (PIG POWER SUPPLY)
B128054E05
Item Item Description: Range
(Display)Inspection Condition Specified Condition
PIG SUPPLY PIG power supply:
Min.: 0 V
Max.: 20.1531 VPower steering in operation 10 to 14 V
CHECK INTERMITTENT PROBLEMS

POWER STEERING – ELECTRONIC POWER STEERING SYSTEMPS–33
PS
(a) Disconnect the A1 power steering ECU connector.
(b) Measure the voltage of the wire harness side connector.
Standard voltage
NG
OK
2CHECK WIRE HARNESS (BATTERY - POWER STEERING ECU)
F100915E03
Tester Connection Specified Condition
A1 -1 (PIG) - A1-2 (PGND) 10 to 14 V
REPAIR OR REPLACE HARNESS AND
CONNECTOR
REPLACE POWER STEERING ECU

2AZ-FE ENGINE CONTROL SYSTEM – SFI SYSTEMES–51
ES
CAT TEMP B1S2Estimated catalyst temperature
(sensor 2):
Min.: -40C, Max.: 6,513.5C--
S O2S B1S2Sub heated oxygen sensor
impedance (sensor2):
Min.: 0
, Max.: 21247.68
--
INI COOL TEMPEngine coolant temperature at
engine start:
Min.: -40
C, Max.: 120CClose to ambient air
temperature-
INI INTAKE TEMPIntake air temperature at engine
start:
Min.: -40
C, Max.: 120CClose to ambient air
temperature-
INJ VOLInjection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.048 ml0 to 0.15 ml: IdlingQuantity of fuel injection volume
for 10 times
STARTER SIGStarter switch (STSW) signal:
ON or OFFON: Cranking -
PS SWPower steering signal:
ON or OFFON: Power steering operation -
PS SIGNALPower steering signal (history):
ON or OFFON: When steering wheel first
turned after battery terminals
connectedSignal status usually ON until
battery terminals disconnected
CTP SWClosed throttle position switch:
ON or OFF• ON: Throttle fully closed
• OFF: Throttle open-
A/C SIGNALA/C signal:
ON or OFFON: A/C ON -
PNP SW [NSW]PNP switch status:
ON or OFFON: P or N position -
ELECT LOAD SIGElectrical load signal:
ON or OFFON: Headlights or defogger
turned ON-
STOP LIGHT SWStop light switch:
ON or OFFON: Brake pedal depressed -
+BMWhether or not electric throttle
control system power inputted:
ON or OFFON: Ignition switch ON and
system normal-
+BM VOLTAGE+BM voltage:
Min.: 0, Max.: 19.9229 to 14 (V): Ignition switch ON
and system normalETCS service data
BATTERY VOLTAGEBattery voltage:
Min.: 0 V, Max.: 65.535 V9 to 14 V: Ignition switch ON -
ACTUATOR POWERActuator power supply:
ON or OFFON: Idling ETCS service data
ATM PRESSUREAtmospheric pressure:
Min.: 0 kPa, Max.: 255 kPaApproximately 100 kPa: Ignition
switch ON-
BATTERY CURRENTBattery current:
Min.: -100 A, Max.: 100 A--
BATTERY TEMPBattery temperature:
Min.: -45
C, Max.: 156.4 F--
ALT OUTPUT DUTYGenerator output duty ratio:
Min.: 0 %, Max.: 100 %- During charge control
ALT V NORMALRequest voltage when regulator
not under forced activation:
Min.: 0 V, Max.: 20 VBattery electrolyte temperature
varies (12.5 to 14.8 V) while
driving:
After engine startAlternator regulator output voltage
is out put
When performing Active Test,
value is 0V
ALT V TSTRequest voltage when regulator
under forced activation:
Min.: 0 V, Max.: 20 VRequest instruction voltage
value:
After engine startCharging control service data
When not performing Active Test,
value is 0V
EVAP (Purge) VSVPurge VSV status:
ON or OFF--
FUEL PUMP / SPDFuel pump status:
ON or OFFON: Engine running Active Test support data Intelligent Tester Display Measurement: Range (Display) Normal Condition*1 Diagnostic Note