sensor TOYOTA SEQUOIA 2001 Service Workshop Manual

A23656
0.2 V/DIV
200 msec./DIV
Ground
A2365710 msec./DIV 5 V/DIV
Ground
± DIAGNOSTICSENGINE
DI±39
233 Author: Date:
2005 SEQUOIA (RM1146U)
WAVEFORM 10
Heated oxygen sensor
ECM Terminal NamesBetween OX1B and E2
Tester Ranges0.2 V/DIV, 200 msec./DIV
ConditionsEngine speed maintained 2,500 rpm for 2 minutes after
warming up sensor
HINT:
In the DATA LIST, item O2S B1S2 shows the ECM input values
from the heated oxygen sensor.
WAVEFORM 11
Engine speed signal
ECM Terminal NamesBetween TACH and E1
Tester Ranges5 V/DIV, 10 msec./DIV
ConditionsIdling
HINT:
The wavelength becomes shorter as vehicle speed increases.

± DIAGNOSTICSENGINE
DI±47
241 Author: Date:
2005 SEQUOIA (RM1146U)P2120
P2121
P2122
P2123
P2125
P2127
P2128
P2138
The accelerator pedal position sensor has two (main and
sub) sensor circuits. If a malfunction occurs in either of the
sensor circuits, the ECM detects the abnormal signal volt-
age difference between the two sensor circuits and
switches to limp mode. In limp mode, the remaining circuit
is used to calculate the accelerator pedal opening to allow
the vehicle to continue driving.
If both circuits malfunction, the ECM regards the opening
angle of the accelerator pedal to be fully closed. In this
case, the throttle valve will remain closed as if the engine is
idling.
ºPassº condition is detected and the ignition switch is turned
OFF.
P2440 and
P1441 and/or
P1444
Restrict the throttle opening angle: Ga
30 g/s
P1441 and P1444Restrict the throttle opening angle: Ga
50 g/s
P1441
P1444Restrict the throttle opening angle: Ga
100 g/s
P2430
P2431
P2432
P2433
Restrict the throttle opening angle: Ga
50 g/s

DID81±01
DI±48
± DIAGNOSTICSENGINE
242 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
By reading the DATA LIST displayed on a hand±held tester, you can check values, including those of the
switches, sensors, and actuators, without removing any parts. Reading the DATA LIST as the first step of
troubleshooting is one method of shortening diagnostic time.
NOTICE:
In the table below, the values listed under Normal Conditions are for reference only. Do not depend
solely on these values when determining whether or not a part is faulty.
(a) Warm up the engine.
(b) Turn the ignition switch to OFF.
(c) Connect a hand±held tester to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the tester ON.
(f) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST.
(g) Check the values by referring to the table below.
Hand±Held Tester DisplayMeasurement Item:Range
(Display)Normal Condition *Diagnostic Note
INJECTOR
Injection period of the No. 1 cylin-
der:
Min.: 0 ms, Max.: 32.64 ms
2.3 to 3.8 ms: Idling'
IGN ADVANCE
Ignition timing advance for No. 1
cylinder/
Min.: ±64 deg., Max.: 63.5 deg.
BTDC 4 to 17°: Idling'
CALC LOADCalculated load by ECM:
Min.: 0 %, Max.: 100 %
11 to 21 %: Idling

12 to 22 %: Running without load
(2,500 rpm)
'
VEHICLE LOADVehicle load:
Min.: 0 %, Max.: 25700 %Actual vehicle load'
MAFAir flow rate from MAF meter:
Min.: 0 g/s, Max.: 655 g/s2.0 to 3.9 g/s: Idling
If the value approximately 0.0 g/s:

Mass air flow meter power
source circuit open

VG circuit open or short
If the value 160.0 g/s or more:

E2G circuit open
ENGINE SPDEngine speed:
Min.: 0 rpm, Max.: 16,383 rpm600
50 rpm: Idling'
VEHICLE SPDVehicle speed:
Min.: 0 km/h, Max.: 255 km/hActual vehicle speedSpeed indicated on speedometer
COOLANT TEMPEngine coolant temperature:
Min.: ±40C, Max.: 140C80 to 100°C
(176 to 212°F): After warming up

If the value ±40C (±40F): sen-
sor circuit open

If the value 140C (284F): sen-
sor circuit shorted
INTAKE AIRIntake air temperature:
Min.: ±40C, Max.: 140CEquivalent to ambient air tempera-
ture

If the value ±40C (±40F): sen-
sor circuit open

If the value 140C (284F): sen-
sor circuit shorted
SECONDARY AIRSecond air system status:
ON or OFFON: Secondary air system opera-
tion'
AIR±FUEL RATIOAir±fuel ratio:
Min.: 0, Max.: 1.9990.8 to 1.2: During idling'
EVAP VAPOR PRESEVAP vapor pressure:
Min.: ±8192 Pa, Max.: 8191 Pa0 Pa: Fuel tank cap removed'

± DIAGNOSTICSENGINE
DI±49
243 Author: Date:
2005 SEQUOIA (RM1146U)PURGE DENSITY
Learning value of purge density/
Min.: ±50, Max.: 350Idling: ±40 to 0 %Service data
PURGE FLOWPurge flow:
Min.: 0 %, Max.: 102.4 %0 to 100 %: Idling'
EVAP PURGE VSVEVAP (Purge) VSV control duty:
Min.: 0 %, Max.: 100 %0 to 100 %: During idlingOrder signal from ECM
VAPOR PRESSVapor pressure:
Min.: ±4.125 kPa, Max.: 2.125 kPa0 kPa: Fuel tank cap removed
Pressure inside fuel tank moni-
tored by the vapor pressure sen-
sor
KNOCK CRRT VAL
Correction learning value of
knocking:
Min.: ±64 CA, Max.: 1,984 CA0 to 22 CA:
Driving, 44 mph (70 km/h)Service data
KNOCK FB VALFeedback value of knocking:
Min.: ±64 CA, Max.: 1,984 CA±22 to 0 CA
Driving, 44 mph (70 km/h)Service data
ACCEL POS #1
Absolute Accelerator Pedal Posi-
tion (APP) No. 1:
Min.: 0 %, Max.: 100 %10 to 22 %: accelerator pedal is
released
54 to 86 %: accelerator pedal is
fully depressed
'
ACCEL POS #2Absolute APP No. 2:
Min.: 0 %, Max.: 100 %
12 to 42 %: accelerator pedal is
released
66 to 98 %: The accelerator pedal
is fully depressed
'
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V'ETCS freeze data
ACCEL POS #1APP sensor No. 1 voltage:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: accelerator pedal is
released.
2.6 to 4.5 V: or pedal is fully de-
pressed.
'
ACCEL POS #2APP sensor No. 2 voltage:
Min.: 0 V, Max.: 5 V
1.2 to 2.0 V: accelerator pedal is
released.
3.4 to 5.3 V: accelerator pedal is
fully depressed.
'
ACCEL IDL POS
Whether or not accelerator pedal
position sensor detecting idle:
ON or OFF
ON: Idling'
THRTL LEARN VAL
Throttle valve fully closed
(learned value):
0.4 to 0.8 V'
ACCEL SSR #1 AD
Accelerator fully closed value No.1
(AD):
Min.: 0, Max.: 4.98 V
'ETCS service data
ACCEL LRN VAL#1
Accelerator fully closed learning
value No.1:
Min.: 0, Max.: 124.512
'ETCS service data
ACCEL LRN VAL#2
Accelerator fully closed learning
value No.2:
Min.: 0, Max.: 124.512
'ETCS service data
FAIL #1
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'
FAIL #2
Whether or not fail safe function
executed:
ON or OFF
ON: ETCS has failed'

DI±50
± DIAGNOSTICSENGINE
244 Author: Date:
2005 SEQUOIA (RM1146U)ST1
Starter signal:
ON or OFFON: Cranking'
SYSGUARD JUDGESystem guard:
ON or OFF'ETCS service data
OPN MALFUNCTIONOpen side malfunction:
ON or OFF'ETCS service data
THROTTLE POSAbsolute throttle position sensor:
Min.: 0 %, Max.: 100 %
10 to 24 %: Throttle fully closed

64 to 96 %: Throttle fully openRead the value with intrusive op-
eration (active test)
THROTTL IDL POS
Whether or not throttle position
sensor detecting idle:
ON or OFF
ON: Idling'
THRTL REQ POSThrottle requirement position:
Min.: 0 V, Max.: 5 V0.5 to 1.0 V: Idling'
THROTTLE POSThrottle sensor positioning:
Min.: 0 %, Max.: 100 %10 to 18 %: IdlingCalculated value based on VTA1
THROTTLE POS #2Throttle sensor positioning #2:
Min.: 0 %, Max.: 100 %'Calculated value based on VTA2
THROTTLE POS #1
Throttle position sensor No. 1
output voltage:
Min.: 0 V, Max.: 4.9 V
'ETCS freeze data
THROTTLE POS #2
Throttle position sensor No.2 out-
put voltage:
Min.: 0 V, Max.: 4.9 V
'ETCS freeze data
THROTTLE POS #1Throttle position No. 1:
Min.: 0 V, Max.: 5 V
0.5 to 1.2 V: Throttle fully closed

3.2 to 4.8 V: Throttle fully opened'
THROTTLE POS #2Throttle position No. 2:
Min.: 0 V, Max.: 5 V
2.0 to 2.9 V: Throttle fully closed

4.6 to 5.5 V: Throttle fully openRead the value with intrusive op-
eration (active test)
THRTL COMND VALThrottle position command value:
Min.: 0 V, Max.: 4.98 V0.5 to 4.8 VETCS service data
THROTTLE SSR #1
Throttle sensor opener position
No. 1:
Min.: 0 V, Max.: 4.98 V
0.6 to 0.9 VETCS service data
THROTTLE SSR #2
Throttle sensor opener position
No. 2:
Min.: 0 V, Max.: 4.98 V
2.2 to 2.6 VETCS service data
THRTL SSR #1 AD
Throttle sensor opener position
No.1 (AD):
Min.: 0 V, Max.: 4.98 V
0.6 to 0.9 VETCS service data
THROTTLE MOT
Whether or not throttle motor con-
trol permitted:
ON or OFF
ON: IdlingRead the value with the power
switch ON (Do not start engine)
THROTTLE MOTThrottle motor current:
Min.: 0 A, Max.: 80 A0 to 3.0 A: Idling'
THROTTLE MOTThrottle motor:
Min.: 0 %, Max.: 100 %0.5 to 40 %: Idling'
THROTTLE MOTThrottle motor current:
Min.: 0 A, Max.: 19.92 A0 to 3.0 A: Idling'
THROTL OPN DUTYThrottle motor opening duty ratio:
Min.: 0 %, Max.: 100 %0 to 40 %: During idlingWhen accelerator pedal de-
pressed, duty ratio increased
THROTL CLS DUTYThrottle motor closed duty ratio:
Min.: 0 %, Max.: 100 %0 to 40 %: During idlingWhen accelerator pedal released
quickly, duty ratio increased
THRTL MOT (OPN)Throttle motor duty ratio (open):
Min.: 0 %, Max.: 100 %'ETCS service data

± DIAGNOSTICSENGINE
DI±51
245 Author: Date:
2005 SEQUOIA (RM1146U)THRTL MOT (CLS)
Throttle motor duty ratio (close):
Min.: 0 %, Max.: 100 %'ETCS service data
O2S B1 S2
Heated oxygen sensor output volt-
age for bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V0.1 to 0.9 V:
Driving 44 mph (70 km/h)
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
O2S B2 S2
Heated oxygen sensor output volt-
age for bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V0.1 to 0.9 V:
Driving 44 mph (70 km/h)
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
AFS B1 S1
A/F sensor output voltage for bank
1 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
AFS B2 S1
A/F sensor output voltage for bank
1 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the INJ VOL or A/F
CONTROL function of the ACTIVE
TEST enables the technician to
check voltage output of the sensor
TOTAL FT #1
Total fuel trim of bank 1
Average value for fuel trim system
of bank 1:
Min.: ±0.5, Max.: 1,496
±0.2 to 0.2: Idling'
TOTAL FT #2
Total fuel trim of bank 1
Average value for fuel trim system
of bank 1:
Min.: ±0.5, Max.: 1,496
±0.2 to 0.2: Idling'
SHORT FT #1Short±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2%0 ± 20 %
This item the short±term fuel com-
pensation used to maintain the
air±fuel ratio at stoichiometric air±
fuel ratio
SHORT FT #2Short±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2%0 ± 20 %
This item the short±term fuel com-
pensation used to maintain the
air±fuel ratio at stoichiometric air±
fuel ratio
LONG FT #1Long±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2 %0 ± 20 %
This item the overall fuel com-
pensation carried out in long±term
to compensate a continual devi-
ation of the short±term fuel trim
from the central value
LONG FT #2Long±term fuel trim of bank 1:
Min.: ±100 %, Max.: 99.2 %0 ± 20 %
This item the overall fuel com-
pensation carried out in long±term
to compensate a continual devi-
ation of the short±term fuel trim
from the central value
FUEL SYS #1
Fuel system status (Bank1):
OL or CL or OL DRIVE or
OL FAULT or CL FAULT
CL: Idling after warming up

OL (Open Loop): Has not yet sa-
tisfied conditions to go closed
loop

CL (Closed Loop): Using heated
oxygen sensor as feedback for
fuel control.

OL DRIVE: Open loop due to
driving conditions (fuel enrich-
ment)

OL FAULT: Open loop due to de-
tected system fault

CL FAULT: Closed loop but
heated oxygen sensor, which
used for fuel control malfunction-
ing

DI±52
± DIAGNOSTICSENGINE
246 Author: Date:
2005 SEQUOIA (RM1146U)FUEL SYS #2
Fuel system status (Bank1):
OL or CL or OL DRIVE or
OL FAULT or CL FAULT
CL: Idling after warming up

OL (Open Loop): Has not yet sa-
tisfied conditions to go closed
loop

CL (Closed Loop): Using heated
oxygen sensor as feedback for
fuel control.

OL DRIVE: Open loop due to
driving conditions (fuel enrich-
ment)

OL FAULT: Open loop due to de-
tected system fault

CL FAULT: Closed loop but
heated oxygen sensor, which
used for fuel control malfunction-
ing
O2FT B1 S2
Short±term fuel trim associated
with the bank 1 sensor 2:
Min.: ±100 %, Max.: 99.2 %
0 ± 20 %Same as SHORT FT #1
O2FT B2 S2
Short±term fuel trim associated
with the bank 1 sensor 2:
Min.: ±100 %, Max.: 99.2 %
0 ± 20 %Same as SHORT FT #1
AF FT B1 S1
Short±term fuel trim associated
with the bank 1 sensor 1:
Min.: 0, Max.: 1.999

Value less than 1 (0.000 to
0.999) = Lean

Stoichiometric air±fuel ratio=1

Value greater than 1 (1.001 to
1.999) = RICH
'
AF FT B2 S1
Short±term fuel trim associated
with the bank 1 sensor 1:
Min.: 0, Max.: 1.999

Value less than 1 (0.000 to
0.999) = Lean

Stoichiometric air±fuel ratio=1

Value greater than 1 (1.001 to
1.999) = RICH
'
CAT TEMP B1S1
Catalyst temperature (Bank 1,
Sensor 1):
Min.: ±40, Max.: 6,513.5 C
''
CAT TEMP B2S1
Catalyst temperature (Bank 1,
Sensor 1):
Min.: ±40, Max.: 6,513.5 C
''
CAT TEMP B1S2
Catalyst temperature (Bank 1,
Sensor 2):
Min.: ±40, Max.: 6,513.5 C
''
CAT TEMP B2S2
Catalyst temperature (Bank 1,
Sensor 2):
Min.: ±40, Max.: 6,513.5 C
''
INI COOL TEMPInitial engine coolant temperature:
Min.: ±40C, Max.: 140CClose to ambient air temperatureService data
INI INTAKE TEMPInitial intake air temperature:
Min.: ±40C, Max.: 140CClose to ambient air temperatureService data
INJ VOLInjection volume (cylinder 1):
Min.: 0 ml, Max.: 2.048 ml0 to 0.5 mlQuantity of fuel injection volume
for 10 times
STARTER SIGStarter signal: ON or OFFON: Cranking'
PS SWPower steering signal:
ON or OFFON: Power steering operation'
PS SIGNALPower steering signal:
ON or OFFON: When steering wheel first
turned after ignition switch turned
to ONThis signal status usually ON until
ignition switch turned to OFF
CTP SWClosed throttle position switch:
ON or OFF
ON: Throttle fully closed

OFF: Throttle open'

DI±54
± DIAGNOSTICSENGINE
248 Author: Date:
2005 SEQUOIA (RM1146U)FC TAU
Fuel cut TAU: Fuel cut during very
light load:
ON or OFF
ON: Fuel cut operating
The fuel cut being performed un-
der very light load to prevent the
engine combustion from becoming
incomplete
IGNITIONIgnition counter:
Min.: 0, Max.: 8000 to 800'
CYL #1, #2, #3, #4, #5, #6, #7, #8Misfire ratio of the cylinder 1 to 4:
Min.: 0, Max.: 2550 %This item displayed in only idling
CYL ALLAll cylinders misfire rate:
Min.: 0, Max.: 2550 to 35'
MISFIRE RPMEngine RPM for first misfire range:
Min.: 0 rpm, Max.: 6,375 rpm0 rpm: Misfire 0'
MISFIRE LOADEngine load for first misfire range:
Min.: 0 g/rev, Max.: 3.98 g/rev0 g/rev: Misfire 0'
MISFIRE MARGINMisfire monitoring:
MIn.: ±100 %, Max.: 99.22 %±100 to 99.2 %Misfire detecting margin
#CODES#Codes:
Min.: 0, Max.: 255'Number of detected DTCs
CHECK MODECheck mode:
0: ON, 1: OFFON: Check mode ONSee page DI±44
SPD TEST
Check mode result for vehicle
speed sensor:
0: COMPL, 1: INCOMPL
''
AS TEST
Check mode result for secondary
air injection system:
0: COMPL, 1: INCOMPL
''
MISFIRE TEST
Check mode result for misfire
monitor:
0: COMPL, 1: INCOMPL
''
OXS1 TEST
Check mode result for HO2 sen-
sor :
0: COMPL, 1: INCOMPL
''
OXS2 TEST
Check mode result for HO2 sen-
sor :
0: COMPL, 1: INCOMPL
''
A/F SSR TEST B1
Check mode result for air±fuel ra-
tio sensor :
0: COMPL, 1: INCOMPL
''
A/F SSR TEST B2
Check mode result for air±fuel ra-
tio sensor :
0: COMPL, 1: INCOMPL
''
MILMIL status:
ON or OFFON: MIL ON'
MIL ON RUN DIST
MIL ON Run Distance:
Min.: 0 second,
Max.: 65,535 seconds
Distance after DTC detected'
MIL ON RUN TIME
Running time from MIL ON:
Min.: 0 minute,
Max.: 65,535 minutesEquivalent to running time after
MIL was ON'
ENG RUN TIME
Engine run time:
Min.: 0 second,
Max.: 65,535 seconds
Time after engine startService data
TIME DTC CLEAR
Time after DTC cleared:
Min.: 0 minute,
Max.: 65,535 minutesEquivalent to time after DTCs
were erased'

± DIAGNOSTICSENGINE
DI±55
249 Author: Date:
2005 SEQUOIA (RM1146U)DIST DTC CLEAR
Distance after DTC cleared:
Min.: 0 km/h, Max.: 65535 km/hEquivalent to drive distance after
DTCs were erased'
WU CYC DTC CLEARWarm±up cycle after DTC cleared:
Min.: 0, Max.: 255'Number of warm±up cycles after
DTC cleared
MODEL CODEModel code:'Identifying the model code:
UCK30 (2WD), UCK40 (4WD)
ENGINE TYPEEngine type:'Identifying the engine type:
2UZFE
CYLINDER NUMBERCylinder number:
Min.: 0, Max.: 255'Identifying the cylinder number:
8
TRANSMISSIONTransmission type:'Identifying the transmission type:
ECT(5AT)
DESTINATIONDestination'Identifying the destination:
A (America)
MODEL YEARModel year:
Min.: 0, Max.: 255'Identifying the model year:
200#
SYSTEMSystem identification'Identifying the engine system:
GASLIN (gasoline engine)
AI STATUSAI operation prohibit:
OK or NGOK
*1: If no idling conditions are specified, the transmission gear selector lever should be in the N or P position,
and the A/C switch and all accessory switches should be OFF.
2. ACTIVE TEST
HINT:
Performing an ACTIVE TEST enables components including the relays, VSV (Vacuum Switching Valve),
and actuators, to be operated without removing any parts. The ACTIVE TEST can be performed with a
hand±held tester. Performing an ACTIVE TEST as the first step of troubleshooting is one method of shorten-
ing diagnostic time.
DATA LIST can be displayed during ACTIVE TESTs.
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the tester ON.
(d) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST.
(e) Perform the ACTIVE TEST by referring to the table below.
Hand±held Tester DisplaysTest DetailsControl RangesDiagnostic Notes
INJ VOLChange injection volumeBetween ±12 % and 25 %

All injectors tested at the same
time

Perform test at less than 3,000
rpm

Injection volume can be changed
in 1 % graduations within control
range
A/F CONTROLChange injection volumeLower by 12.5 % or increase by 25
%

Perform test at less than 3,000
rpm

A/F CONTROL enables checking
and graphing of A/F (Air Fuel Ra-
tio) sensor and Heated Oxygen
(HO2) sensor voltage outputs

To conduct test, select following
menu items: ACTIVE TEST / A/F
CONTROL / USER DATA / AFS
B1S1 and O2S B1S2, and press
YES and ENTER followed by F4
EVAP VSV (ALONE)Activate EVAP VSV controlON/OFF±

DI3HB±12
DI±58
± DIAGNOSTICSENGINE
252 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for the codes listed
in the table below. For details of each code, refer to the ºSee pageº under the respective ''DTC No.'' in the
DTC chart.
DTC No.
(See page)Detection ItemTrouble AreaMIL*1Memory
P0010
(DI±73)Camshaft Position ºAº Actuator
Circuit (Bank 1)
Open or short in OCV circuit

OCV

ECM

P0011
(DI±79)Camshaft Position ºAº ±Timing
Over± Advanced or System Per-
formance (Bank 1)
Valve timing

OCV

VVT controller assembly

ECM

P0012
(DI±79)Camshaft Position ºAº ±Timing
Over± Retarded (Bank 1)

Valve timing

OCV

VVT controller assembly

ECM

P0016
(DI±85)Crankshaft Position ± Camshaft
Position Correlation (Bank 1
Sensor A)
Open or short in VVT sensor circuit

VVT sensor

ECM

P0018
(DI±85)Crankshaft Position ± Camshaft
Position Correlation (Bank 2
Sensor A)
Open or short in VVT sensor circuit

VVT sensor

ECM

P0020
(DI±73)Camshaft Position ºAº Actuator
Circuit (Bank 2)
Open or short in OCV circuit

OCV

ECM

P0021
(DI±79)Camshaft Position ºAº ±Timing
Over± Advanced or System Per-
formance (Bank 2)
Valve timing

OCV

VVT controller assembly

ECM

P0022
(DI±79)Camshaft Position ºAº ±Timing
Over± Retarded (Bank 2)

Valve timing

OCV

VVT controller assembly

ECM

P0031
(DI±88)Oxygen (A/F) Sensor Heater
Control Circuit Low (Bank 1 Sen-
sor 1)
Open in heater circuit of A/F sensor

A/F sensor heater

A/F relay

ECM

P0032
(DI±88)Oxygen (A/F) Sensor Heater
Control Circuit High (Bank 1
Sensor 1)
Short in heater circuit of A/F sensor

A/F sensor heater

A/F relay

ECM

P0037
(DI±93)Oxygen Sensor Heater Control
Circuit Low (Bank 1 Sensor 2)

Open in heater circuit of heated oxygen sensor

Heated oxygen sensor heater

EFI relay

ECM

P0038
(DI±93)Oxygen Sensor Heater Control
Circuit High (Bank 1 Sensor 2)

Short in heater circuit of heated oxygen sensor

Heated oxygen sensor heater

EFI relay

ECM