check oil TOYOTA TERCEL 1996 Service Workshop Manual

LU-16
- LUBRICATIONOIL PUMP
1996 TERCEL (RM440U)
(a) Place a new gasket on the exhaust pipe.
(b) Connect the exhaust pipe to the exhaust manifold with 2
compresson springs and 2 bolts.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
6. w/ A/C:
INSTALL A/C COMPRESSOR AND MOUNTING
BRACKET
(a) Install the compressor mounting bracket with the 4 bolts.
Torque: 27 N´m (270 kgf´cm, 20 ft´lbf)
(b) Install the A/C compressor to the bracket with the 4 bolts.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
(c) Connect the A/C compressor connector.
7. INSTALL CRANKSHAFT TIMING PULLEY (See page
EM-17)
8. INSTALL TIMING BELT (See page EM-17)
9. INSTALL OIL DIPSTICK
10. FILL WITH ENGINE OIL
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK ENGINE OIL LEVEL
13. INSTALL HOOD

IG08E-06
CHECK POWER SUPPLY TO IGNITION COIL
AND IGNITER
SPARK TEST
Replace the camshaft position sensor.
CHECK RESISTANCE OF HIGH-TENSION
CORD (See step 2)
Maximum resistance: 25 kW per cord
CHECK RESISTANCE OF IGNITION COIL
(See step 4) 1. Turn ignition switch to ON.
2. Check that there is battery voltage at
ignition coil positive (+) terminal.
CHECK CONNECTION OF IGNITION COIL IGNITER
Resistance: Cold Hot
Secondary
9.3 - 16.0 kW
11.7 - 18.8 kW
CHECK RESISTANCE OF CAMSHAFT POSITION SENSOR
(See step 5)
Resistance:Cold Hot
985 - 1,600 W1,265 - 1,890 W
CHECK IGT SIGNAL FROM ECM
(See page
DI-84)
CHECK RESISTANCE OF CRANKSHAFT POSITION SENSOR
(See step 6)
Resistance:Cold
Hot
TRY ANOTHER IGNITERReplace the crankshaft position sensor. Replace the ignition coil. Connect securely.
Replace the cord(s).
Check wiring between ignition switch
to ignition coil and igniter.
Check wiring between ECM, distributor
and igniter, and then try another ECM.
NO
OK OK
OK
OK
OK
OKBAD
BAD
BAD
BAD
BAD
BAD
BAD
Primary
0.67 - 1.05 kW0.85 - 1.23 kW
985 - 1,600 W1,265 - 1,890 W
- IGNITIONIGNITION SYSTEM
IG-1
632 Author
: Date
:
1996 TERCEL (RM440U)
IGNITION SYSTEM
ON-VEHICLE INSPECTION
NOTICE:
ºColdº and ºHotº in following sentences express the tem-
perature of the coils themselves. ºColdº is from -10°C
(14°F) to 50°C (122°F) and ºHotº is from 50°C (122°F) to
100°C (212°F).
1. INSPECT SPARK TEST
Check that the spark occurs.
(1) Disconnect the high-tension cord from the spark
plug.
(2) Remove the spark plugs.
(3) Install the spark plugs to the high-tension cord.
(4) Ground the spark plug.
(5) See if spark occurs while engine is being cranked.
NOTICE:
To prevent gasoline from being injected from injectors dur-
ing this test, crank the engine for no more than 5 - 10 se-
conds at time. If the spark done not occur, do the test as fol-
lows:

P20908
CORRECT
WRONG
S06255
P21178
Ohmmeter
S06256
Push
P04690
CORRECT
WRONG IG-2
- IGNITIONIGNITION SYSTEM
633 Author
: Date
:
1996 TERCEL (RM440U)
2. INSPECT HIGH-TENSION CORDS
(a) Disconnect the high-tension cords from the spark plugs.
(1) Disconnect the high-tension cords at the rubber
boot. Do not pull on the cords.
NOTICE:
Pulling on or bending the cords may damage the conductor
inside.
(2) Disconnect the high-tension cords from the clamp.
(b) Disconnect the high-tension cords from the ignition coils.
(1) Using a screwdriver, lift up the lock claw and discon-
nect the holder from the ignition coils.
(2) Disconnect the high-tension cord at the grommet.
(3) Do not pull on the cord.
NOTICE:
Pulling on or bending the cords may damage the conductor
inside. Do not wipe any of the oil from the grommet after the
high-tension cord is disconnected.
(c) Reconnect the high-tension cords to the ignition coils.
Maximum resistance: 25 kW per cord
If the resistance is greater than maximum, check the terminals.
If necessary, replace the high-tension cord.
(d) Reinstall the high-tension cords.
(1) Assemble the holder and grommet.
(2) Align the spline of the ignition coil with the spline of
the holder, and push in the cord.
NOTICE:
Check that the holder is correctly installed to the grommet
and distributor cap as shown in the illustration.
(3) Check that the lock claw of the holder is engaged by
lightly pulling the holder.
(4) Connect the high-tension cords to the clamp.
(e) Reconnect high-tension cords to spark plugs.

S06257
16 mm Plug Wrench
IG0152
P20433
P20584
- IGNITIONIGNITION SYSTEM
IG-3
634 Author
: Date
:
1996 TERCEL (RM440U)
3. INSPECT SPARK PLUGS
(a) Disconnect high-tension cords from spark plugs.
(b) Using a 16 mm plug wrench, remove the spark plug.
(c) Using a spark plug cleaner or wire brush, clean the spark
plug.
If the electrode has traces of wet carbon, allow it to dry and then
clean with a spark plug cleaner.
Air pressure:
Below 588 kPa (6 kgf/cm
2, 85 psi)
Duration: 20 seconds or less
HINT:
If there are traces of oil, remove it with gasoline before using the
spark plug cleaner.
(d) Visually checkthe spark plug for thread damage and insu-
lator damage.
If abnormal, replace the spark plug.
Recommended spark plug:
DENSOK16TR11
NGKBKR5EKB11
(e) Inspect the electrode gap.
Correct electrode gap: 1.1 mm (0.043 in.)
(f) Using a 16 mm plug wrench, remove the spark plug.
Torque: 18 N´m (180 kgf´cm, 13 ft´lbf)
(g) Reconnect the high-tension cords from the ignition coils.

ST0199
Continuity
ST0200
No Continuity
N00337
ST0019
ST0203
Continuity
- STARTINGSTARTER (Reduction Type)
ST-7
1996 TERCEL (RM440U)
7. INSPECT FIELD COIL FOR OPEN CIRCUIT
Using an ohmmeter, check that there is continuity between the
lead wire and field coil brush lead.
If there is no continuity, replace the field frame.
8. INSPECT FIELD COIL FOR GROUND
Using an ohmmeter, check that there is no continuity between
the field coil end and field frame.
If there is continuity, replace the field frame.
9. INSPECT BRUSH LENGTH
Using a vernier caliper, measure the brush length.
Standard length: 13.5 mm (0.531 in.)
Minimum length: 8.5 mm (0.334 in.)
If the length is less than minimum, replace the brush holder and
field frame.
10. INSPECT BRUSH SPRING LOAD
Take the pull scale reading the instant the brush spring sepa-
rates from the brush.
Standard spring installed load:
17.6 - 23.5 N (1.79 - 2.39 kgf, 4.0 - 5.3 lbf)
Minimum spring installed load:
11.8 N (1.2 kgf, 2.6 lbf)
If the installed load is not as specified, replace the brush
springs.
11. INSPECT BRUSH HOLDER INSULATION
Using an ohmmeter, check that there is no continuity between
the positive (+) and negative (-) brush holders.
If there is continuity, repair or replace the brush holder.
12. INSPECT GEAR TEETH
Check the gear teeth on the pinion gear, idle gear and the clutch
assembly for wear or damage.
If damaged, replace the gear or clutch assembly.
If damaged, also check the drive plate ring gear for wear or
damage.

P10821
Free
Lock
ST0204
Terminal 50
Continuity
Terminal C
ST0205
Continuity Terminal 50Switch Body ST-8
- STARTINGSTARTER (Reduction Type)
1996 TERCEL (RM440U)
13. INSPECT CLUTCH PINION GEAR
Rotate the pinion gear clockwise, and check that it turns freely.
Try to rotate the pinion gear counterclockwise and check that
it locks.
If necessary, replace the clutch assembly.
14. INSPECT REAR BEARING
Turn each bearing by hand while applying inward force.
If resistance is felt or the bearing sticks, replace the bearing.
15. INSPECT FRONT BEARING
Turn each bearing by hand while applying inward force.
If resistance is felt or the bearing sticks, replace the bearing.
16. DO PULL-IN COIL OPEN CIRCUIT TEST
Using an ohmmeter, check that there is continuity between ter-
minals 50 and C.
If there is no continuity, check and replace the magnetic switch.
17. DO HOLD-IN COIL OPEN CIRCUIT TEST
Using an ohmmeter, check that there is continuity between ter-
minal 50 and the switch body.
If there is no continuity, check and replace the magnetic switch.

P25608
Wooden
Block
40 mm
37 mm
20 mmContact
Plate
V06796
P25609
SST
P25479
- STARTINGSTARTER (Reduction Type)
ST-1 1
1996 TERCEL (RM440U)
(f) Temporarily tighten the terminal nuts.
(g) Tighten the terminal nut.
(1) Put a wood block on the contact plate and press it
down with a hand press.
Dimensions of wood block:
20 x 37 x 40 mm (0.97 x 1.46 x 1.57 in.)
Press force:
981 N (100 kgf, 221 lbf)
NOTICE:

Check the diameter of the hand press ram. Then cal-
culate the gauge pressure of the press when 981 N
(100 kgf, 221 lbf) of force is applied.

If the contact plate is not pressed down with the spe-
cified pressure, the contact plate may tilt due to coil
deformation or the tightening of the nut.
(2) Using SST, tighten the nut to the specified torque.
SST 09810-38140
Torque: 17 N´m (173 kgf´cm, 12 ft´lbf)
NOTICE:
If the nut is over tightened, it may cause cracks on the in-
side of the insulator.
(h) Clean the contact surfaces of the contact plate and plung-
er.
Clean the contact surfaces of the remaining contact plate
and plunger with a dry shop rag.
(i) Reinstall the magnetic switch end cover.
Install the plunger, new gasket, end cover and lead clamp
with 3 bolts.
Torque: 3.6 N´m (36 kgf´cm, 32 in.´lbf)

ST0J1-01
P13459
Terminal 50
Terminal C
Battery
P13460
Terminal C
Battery
Disconnect
P13461
Battery
Disconnect
P13462
Battery
Ammeter Terminal 50
Terminal 30
- STARTINGSTARTER (Reduction Type)
ST-13
1996 TERCEL (RM440U)
TEST
NOTICE:
These tests must be performed within 3 to 5 seconds to
avoid burning out the coil.
1. DO HOLD-IN TEST
(a) Disconnect the field coil lead wire from terminal C.
(b) Connect the battery to the magnetic switch as shown.
Check that the clutch pinion gear moves outward.
2. DO HOLD-IN TEST
With battery connected as above with the clutch pinion gear
out, disconnect the negative (-) lead from terminal C. Check
that the pinion gear remains out.
3. INSPECT CLUTCH PINION GEAR RETURN
Disconnect the negative (-) lead from the switch body.
Check that the clutch pinion gear returns inward.
4. DO NO-LOAD PERFORMANCE TEST
(a) Connect the battery and ammeter to the starter as shown.
(b) Check that the starter rotates smoothly and steadily with
the pinion gear moving out. Check that the ammeter the
current specified in the respective repair manual.

ST083-07
ST0663
Continuity
ST0664No Continuity
Z03211
Z03209
ST0040
- STARTINGSTARTER (Planetary Type)
ST-19
1996 TERCEL (RM440U)
INSPECTION
1. INSPECT ARMATURE COIL
(a) Check the commutator for open circuit.
Using an ohmmeter, check that there is continuity be-
tween the segments of the commutator.
If there is no continuity between any segment, replace the ar-
mature.
(b) Check the commutator for ground.
Using an ohmmeter, check that there is no continuity be-
tween the commutator and armature coil core.
If there is continuity, replace the armature.
(c) Check the commutator for dirty and burnt surface.
If the surface is dirty or burn, correct with sandpaper (No.400)
or a lathe.
(d) Check for the commutator circle runout.
(1) Place the commutator on V-blocks.
(2) Using a dial gauge, measure the circle runout.
Maximum circle runout: 0.05 mm (0.0020 in.)
If the circle runout is greater than maximum, correct it on a lathe.
(e) Using vernier calipers, measure the commutator diame-
ter.
Standard diameter: 28.0 mm (1.102 in.)
Minimum diameter: 27.0 mm (1.063 in.)
If the diameter is less than minimum, replace the armature.
(f) Check that the undercut depth is clean and free of foreign
materials. Smooth out the edge.
Standard undercut depth: 0.6 mm (0.024 in.)
Minimum undercut depth: 0.2 mm (0.008 in.)
If the undercut depth is less than minimum, correct it with a
hacksaw blade.

ST0666
Continuity
ST0665No Continuity
ST0648
ST0019
ST0660
No Continuity ST-20
- STARTINGSTARTER (Planetary Type)
1996 TERCEL (RM440U)
2. INSPECT FIELD COIL
(a) Check the field coil for open circuit.
Using an ohmmeter, check that there is continuity be-
tween the lead wire and field coil brush lead.
If there is no continuity, replace the field frame.
(b) Check the field coil for ground.
Using an ohmmeter, check that there is no continuity be-
tween the field coil end and field frame.
If there is continuity, repair or replace the field frame.
3. INSPECT BRUSHES
Check the brush length.
Using vernier calipers, measure the brush length.
Standard length: 14.0 mm (0.551 in.)
Minimum length: 9.0 mm (0.354 in.)
If the length is less than minimum, replace the brush (field frame
side) or brush holder, and dress with an emery cloth.
4. INSPECT BRUSH SPRINGS
Check the brush spring load.
Take the pull scale reading the instant the brush spring
separates from the brush.
Spring installed load:
13.7 - 17.6 N (1.4 - 1.8 kgf, 3.1 - 4.0 lbf)
Minimum spring installed load:
8.8 N (0.9 kgf, 2.0 lbf)
If the installed load is not as specified, replace the brush
springs.
5. INSPECT BRUSH HOLDER
Check the brush holder insulation.
Using an ohmmeter, check that there is no continuity be-
tween the positive (+) and negative (-) brush holders.
If there is continuity, repair or replace the brush holder.