engine TOYOTA URBAN CRUISER 2015 Workshop Manual

196
URBAN CRUISER_OM_OM52F47E_(EE)
2-2. Instrument cluster
Gauges and meters
Instrument cluster light control button
To adjust the brightness of the instrument cluster light. ( →P. 197)
Speedometer
Displays the vehicle speed.
“MODE” button
Switches the multi-information display. Pushing and holding the button
will reset the trip meter when the trip meter is being displayed.
Multi-information display
→P. 202
Tachometer
Displays the engine speed in revolutions per minute.
Fuel gauge and instrument cluster light control display
Displays the quantity of fuel remaining in the tank.

197
2-2. Instrument cluster
2
When driving
URBAN CRUISER_OM_OM52F47E_(EE)
Instrument cluster light control
To adjust the brightness of the instrument cluster lights, push the
switch. Darker
Brighter
■The meters and display illuminate when
Vehicles without a smart entry & start system
The engine switch is in the “ON” position.
Vehicles with a smart entry & start system
The “ENGINE START STOP” switch is in IGNITION ON mode.
NOTICE
■To prevent damage to the engine and its components
●Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
● The engine may be overheating if the high engine coolant temperature
warning light comes on. In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. (
→P. 493)

199
2-2. Instrument cluster
2
When driving
URBAN CRUISER_OM_OM52F47E_(EE)
■
Indicators
The indicators inform the driver of the operating state of the
vehicle’s various systems.
Turn signal indicator
(→ P. 193)
(4WD models)
Four-wheel drive lock
indicator ( →
P. 229)
Headlight high beam
indicator ( →P. 208)Low engine coolant
temperature indicator
Tail light indicator
(→ P. 207)
(if equipped)
Slip indicator ( →P. 224)
(if equipped)
Front fog light indicator
(→ P. 2 1 1 )
(if equipped)
VSC OFF indicator
(→ P. 225)
Rear fog light indicator
(→ P. 2 1 1 )“TRC OFF” indicator
(→ P. 224)
Gear Shift Indicator
(→ P. 190)
(diesel engine)
Engine preheating
indicator ( →P. 185, 181)
(if equipped)
“ECO” indicator
(→ P. 217)“PASSENGER
AIRBAG” indicator
(→ P. 140)
(if equipped)
“ECO OFF” indicator
(→ P. 217)
*1
*1, 2
*1, 4
*1
*1
*1*1
*1

200
2-2. Instrument cluster
URBAN CRUISER_OM_OM52F47E_(EE)
■ Warning lights
Warning lights inform the driver of malfunctions in any of the
vehicle’s systems. ( →P. 439)
*1: These lights turn on when the engine switch is turned to the “ON”
position (vehicles without a smart entry & start system) or the
“ENGINE START STOP” switch is turned to IGNITION ON mode
(vehicles with a smart entry & start system) to indicate that a
system check is being performed. They will turn off after the engine
is started, or after a few seconds. There may be a malfunction in a
system if a light does not come on, or if the lights do not turn off.
Have the vehicle inspected by any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional for
details.
*2: The indicator flashes to indicate that the system is operating.
*3: The indicator comes on to indicate a malfunction.
*4: The indicator comes on to indicate that the system is off.
(if equipped)(diesel
engine)(diesel
engine)
(diesel
engine)(if equipped)(4WD
models)
*1*1*1*1*1*1*1*1
*1, 3*1
*1*1, 3

201
2-2. Instrument cluster
2
When driving
URBAN CRUISER_OM_OM52F47E_(EE)
CAUTION
■
If a safety system warning light does not come on
Should a safety system light such as the ABS or SRS warning light not come
on when you start the engine, this could mean that these systems are not
available to help protect you in an accident, which could result in death or
serious injury. Have the vehicle inspected by any authorized Toyota dealer or
repairer, or another duly qualified and equipped professional immediately if
this occurs.

204
2-2. Instrument cluster
URBAN CRUISER_OM_OM52F47E_(EE)
● Average vehicle speed
● Driving range
● Outside temperature display Displays the average vehicle speed since the
engine was started.
Displays the estimated maximum distance that
can be driven with the quantity of fuel remaining.
• This distance is computed based on your aver-
age fuel consumption. As a result, the actual dis-
tance that can be driven may differ from that
displayed.
• When only a small amount of fuel is added to the tank, the display may not be updated.
Displays the outside temperature.
The temperature range that can be displayed is
from -40°C (-40°F) to 50°C (122°F).
When the outside air temperature falls below 3°C
(37°F) while driving, the temperature display flashes
to indicate that the outside air temperature is
becoming low.

205
2-2. Instrument cluster
2
When driving
URBAN CRUISER_OM_OM52F47E_(EE)
●
Stop & Start system total operation time (if equipped)
● Stop & Start system operation time (if equipped) Displays the total amount of time that the engine
has been stopped due to operation of the Stop &
Start system since the system was last reset.
Press and hold the button to reset.
Displays the amount of time the engine was
stopped due to operation of the Stop & Start sys-
tem during the current trip (from the “ENGINE
START STOP” switch in the IGNITION ON mode
to the OFF [vehicles with smart entry & start sys-
tem] or from the engine switch in the “ON” posi-
tion to the “LOCK” position [vehicles without
smart entry & start system]).

210
2-3. Operating the lights and wipers
URBAN CRUISER_OM_OM52F47E_(EE)
■ Daytime running light system (if equipped)
To make your vehicle more visible to other drivers, the headlights turn on
automatically whenever the engine is started. Daytime running lights are not
designed for use at night.
■ Light reminder buzzer
Vehicles without smart entry & start system
A buzzer sounds when the engine switch is turned to the “LOCK” or “ACC”
position and the driver’s door is opened while the lights are turned on.
Vehicles with smart entry & start system
A buzzer sounds when the “ENGINE START STOP” switch is turned OFF or
to the ACCESSORY mode and the driver’s door is opened while the lights
are turned on.
NOTICE
■To prevent battery discharge
Do not leave the lights on longer than necessary when the engine is not run-
ning.

214
2-3. Operating the lights and wipers
URBAN CRUISER_OM_OM52F47E_(EE)
■ The windshield wiper and washer can be operated when
Vehicles without smart entry & start system
The engine switch is in the “ON” position.
Vehicles with smart entry & start system
The “ENGINE START STOP” switch is in the IGNITION ON mode.
■ If no windshield washer fluid sprays
Check that the washer nozzles are not blocked and if there is washer fluid in
the windshield washer fluid reservoir.
NOTICE
■When the windshield is dry
Do not use the wipers, as they may damage the windshield.
■ When the washer fluid tank is empty
Do not operate the switch continually as the washer fluid pump may over-
heat.
■ When a nozzle becomes block
Do not try to clear it with a pin or other object. The nozzle will be damaged.

215
2-3. Operating the lights and wipers
2
When driving
URBAN CRUISER_OM_OM52F47E_(EE)
Rear window wiper and washer
■The rear window wiper and washer can be operated when
Vehicles without smart entry & start system
The engine switch is in the “ON” position.
Vehicles with smart entry & start system
The “ENGINE START STOP” switch is in the IGNITION ON mode.
■ If no washer fluid sprays
Check that the washer nozzle is not blocked if there is washer fluid in the
washer fluid reservoir. The wiper operation is selected by moving the lever as follows.
Intermittent window wiper
operation
Normal window wiper oper-
ation
Washer/wiper dual opera-
tion
Washer/wiper dual opera-
tion