tow YAMAHA GP1300R 2007 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2007, Model line: GP1300R, Model: YAMAHA GP1300R 2007Pages: 90, PDF Size: 5.78 MB
Page 3 of 90
Important manual information
EJU30091
Name of Notified Body for exhaust emission assessment: Luxcontrol SA
Address: 1, avenue des Terres Rouges BP 349
Town: Esch-sur-Alzette Post Code:L-4004
Country: Luxembourg ID Number:0882
ECtype-examination Certificate number (if applicable):LC*2003/44*10011
Revision No:
Name of PWC manufacturer:
YAMAHA MOTOR MANUFACTURING CORPORATION OF AMERICA
Address: 1000 GA Highway 34 East
Town:Post Code:30265-1320 Newnan Georgia
Country:USA
Name of Authorized Representative ( if applicable):
YAMAHA MOTOR EUROPE N.V.
Address: Koolhovenlaan 101
Town:Schiphol-Rijk Post Code:1119 NC
Country:The Netherlands
Name of Notified Body for noise emission assessment: Luxcontrol SA
Address:1, avenue des Terres Rouges BP 349
Town:Esch-sur-Alzette Post Code: L-4004
Country:Luxembourg ID Number:0882
Declaration of Conformity for Personal Watercraft (PWC)
with the requirements of Directive 94/25/EC
as amended by Directive 2003/44/EC
UF1G74E0.book Page 1 Monday, July 31, 2006 10:10 AM
Page 7 of 90
Table of contents
Battery ............................................. 61
Cleaning the watercraft ................... 62
Maintenance and adjustments ..... 63
Owner’s/operator’s manual and
tool kit ........................................... 63
Periodic maintenance chart ............. 65
Checking the fuel system ................ 66
Checking the oil injection system .... 66
Checking the jet thrust
nozzle angle ................................. 66
Checking and adjusting the throttle
cable ............................................ 67
Cleaning and adjusting the
spark plugs ................................... 67
Lubrication points ............................ 68
Checking the battery ....................... 69
Fuel injection system ....................... 71
Bleeding the oil pump ...................... 71
Adjusting the Yamaha Adjustable
Sponsons (YAS) .......................... 71
Specifications .................................. 72
Specifications ................................ 72
Trouble recovery ............................. 73
Troubleshooting ........................... 73
Troubleshooting chart ...................... 73
Emergency procedures ................ 76
Cleaning the jet intake and
impeller ........................................ 76
Jumping the battery ......................... 77
Replacing the fuses ......................... 78
Towing the watercraft ...................... 78
Submerged watercraft ..................... 79
UF1G74E0.book Page 2 Monday, July 31, 2006 10:10 AM
Page 20 of 90
Safety information
13
Do not attempt to modify this watercraft!
Modifications to your watercraft may reduce
safety and reliability, and render the water-
craft unsafe or illegal for use.
Attach the engine shut-off cord to your left
wrist and keep it free from the handlebars
so that the engine stops if you, the operator,
fall off. After riding, remove the engine shut-
off cord from the watercraft to avoid acci-
dental starting or unauthorized use by chil-
dren or others.
Scan carefully for swimmers and stay away
from swimming areas. Swimmers are hard
to see and you could accidentally hit some-
one in the water.
Avoid being hit by another boat! You should
always take the responsibility to watch for
traffic; other boaters may not be watching
for you. If they do not see you, or if you ma-
neuver more quickly than other boaters ex-
pect, you risk a collision.
Maintain a safe distance from other boats
and watercraft, and also watch for ski ropes
or fishing lines. Obey the “Safe boating
rules” and be sure to check behind you be-
fore making a turn. (See “Safe boating
rules” on page 15.)
EJU30840
Recommended equipment
The following items should be carried on
board your watercraft:
Sound-signaling device
You should carry a whistle or other sound-
signaling device that can be used to signal
other boats.
Visual distress signals
It is recommended that a pyrotechnic de-
vice, which is approved by the appropriate
authorities, be stored in a waterproof con-
tainer on your watercraft. A mirror can also
be used as an emergency signal. Contact a
Yamaha dealer for more information.
Watch
A watch is helpful so you will know how long
you have been operating the watercraft.
Towline
A towline can be used to tow a disabled wa-
tercraft in an emergency.
UF1G74E0.book Page 13 Monday, July 31, 2006 10:10 AM
Page 34 of 90
Features and functions
27
The bow eye is used to attach a rope to the
watercraft when transporting, mooring, or
towing it in an emergency.
EJU36020Stern rope holes
The stern rope holes are located at the stern
of the watercraft.
The stern rope holes are used to attach a rope
to the watercraft when transporting or moor-
ing it.
EJU31370Yamaha Engine Management System
(YEMS)
This model is equipped with an integrated,
computerized management system that con-
trols and adjusts ignition timing, fuel injection,
engine diagnostics, and the off-throttle steer-
ing (OTS) system.
EJU31420Multifunction information center
This meter contains the following functions for
help and convenience in operating the water-
craft.
CAUTION:
ECJ00060
Do not run the engine over 4000 r/min
when checking the operation of the
meter on land without supplying water,
otherwise the engine could overheat
and the catalytic converter could be se-
riously damaged.
Use the specified resistor-type spark
plugs and caps, otherwise the meter
may function erratically.
NOTE:
When the engine is started, all displays light
up for a few seconds, the buzzer sounds
twice, and then the meter starts to operate
normally.
1Bow eye
1Stern rope hole
1Tachometer
2Speedometer
3Hour meter/voltmeter
4Fuel level meter
5“WARNING” light
6Fuel level warning indicator
7Oil level warning indicator
8Engine overheat warning indicator
9Exhaust temperature warning indicator
10Check engine warning indicator
11Select button
UF1G74E0.book Page 27 Monday, July 31, 2006 10:10 AM
Page 38 of 90
Features and functions
31
speeds. If this occurs, the “WARNING” light
and the engine overheat warning indicator
come on and the buzzer sounds continuously.
In addition, the warning system will cut the ig-
nition to the engine to reduce the risk of se-
vere overheating. The engine cannot be
started until it cools down, so it may be neces-
sary to have the watercraft towed back to the
shore. (See “Towing the watercraft” on page
78 for towing procedures.)
The warning signals will be cleared when the
engine is restarted after it has cooled down.
NOTE:
If multiple warnings occur at the same time,
their priority is as follows:
(1) Final engine overheat warning
(2) Fuel level warning
(3) Oil level warning
(4) Initial engine overheat warning
(5) Exhaust temperature warning
(6) Check engine warning
EJU31610Exhaust temperature warning indicator
This model is equipped with an exhaust tem-
perature warning system.
If the exhaust temperature becomes too hot,
the “WARNING” light and the exhaust tem-
perature warning indicator begin to blink, and
the buzzer sounds intermittently.If this occurs, reduce the engine speed and
return to shore to allow the exhaust system to
cool down.
WARNING
EWJ00830
Do not touch the hot muffler or catalytic
converter during or immediately after en-
gine operation; they can cause serious
burns. In addition, the catalytic converter
becomes hotter after the engine stops be-
fore cooling down.
CAUTION:
ECJ00810
This model is equipped with a catalytic
converter.
If the “WARNING” light, exhaust temper-
ature warning indicator, and buzzer
come on, reduce the engine speed (be-
low 4000 r/min) and return to shore.
If you cannot locate and correct the
cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe en-
gine damage.
The warning signals will be cleared when the
engine is restarted after it has cooled down.
EJU31630Check engine warning indicator
If a sensor malfunction or a short circuit is de-
tected, the “WARNING” light and the check
UF1G74E0.book Page 31 Monday, July 31, 2006 10:10 AM
Page 40 of 90
Features and functions
33
NOTE:
The front storage compartment can be re-
moved to access the engine compartment.
To close the front storage compartment, push
down on the rear of the hood until it latches
securely.
NOTE:
Make sure that the front storage compartment
is securely closed before operating the water-
craft.
EJU31731Glove compartment
The glove compartment is located in front of
the seat.To open the glove compartment, slide the
glove compartment latch toward you, and
then lift up the lid.
To close the glove compartment, push the lid
down until it latches securely.
EJU31771Yamaha Adjustable Sponsons (YAS)
The positions of the Yamaha Adjustable
Sponsons are adjustable to allow the operator
to enhance either straight-line performance or
turning performance according to preference
1Glove compartment latch
1Glove compartment
Glove compartment:
Capacity:
2.0 L (0.5 US gal) (0.4 Imp.gal)
Load limit:
1.0 kg (2 lb)
UF1G74E0.book Page 33 Monday, July 31, 2006 10:10 AM
Page 61 of 90
Operation
54
(5) Gradually increase the speed to balance
the watercraft.
EJU33210Capsized watercraft
If the watercraft capsizes, turn it over immedi-
ately.
Be sure to carefully follow the procedures be-
low to prevent injury, or damage to the water-
craft.
WARNING
EWJ00670
IMPROPER UPRIGHTING CAN CAUSE IN-
JURY:
Be sure to shut the engine off by pulling
on the engine shut-off cord to remove
the clip from the engine shut-off switch.
Do not put your hands in the intake
grate.
(1) Remove the clip from the engine shut-off
switch.
(2) Swim to the rear of the watercraft. Pull the
watercraft over with your left hand on theride plate while pushing down on the gun-
wale with your right hand or foot.
NOTE:
If the port (left) side of the capsized watercraft
is tilting up, push down on the gunwale so that
the port (left) side is down before turning the
watercraft clockwise.
CAUTION:
ECJ00540
Do not turn the watercraft over counter-
clockwise, otherwise water can enter the
engine, which can result in severe dam-
age.
(3) Start the engine and operate the water-
craft to discharge any water remaining in
the engine compartment. (If the engine
does not start, see “Towing the water-
craft” on page 78 or “Submerged water-
craft” on page 79.)
UF1G74E0.book Page 54 Monday, July 31, 2006 10:10 AM
Page 66 of 90
Operation
59
(12) Allow the engine compartment to air dry
completely before installing the seat.
NOTE:
Cover the watercraft after the engine and cat-
alytic converter have cooled down.
EJU33430
Transporting
When transporting the watercraft on a trailer,
secure the tie downs to the trailer through the
bow eye and stern rope holes.
CAUTION:
ECJ00610
Do not route ropes or tie downs over the
seat, as they may leave permanent marks
on the seat’s surface. Also, wrap the ropes
or tie downs with towels or rags where
they touch the body of the watercraft to
avoid scratching or damage.
UF1G74E0.book Page 59 Monday, July 31, 2006 10:10 AM
Page 85 of 90
Trouble recovery
78
gine. Any wrong connection could dam-
age the electrical system.
(4) Start the engine, and then disconnect the
jumper cables by reversing the steps
above.
CAUTION:
ECJ00690
Never push the start switch while the en-
gine is running.
Do not operate the start switch for more
than 5 seconds, otherwise the battery
will be discharged and the engine will
not start. Also, the starter motor could
be damaged. If the engine does not start
in 5 seconds, release the start switch,
wait 15 seconds, and then try again.
EJU34680Replacing the fuses
The fuses are located in the electrical box.
To replace a fuse:
(1) Remove the cap on the electrical box.
(2) Replace the blown fuse with the spare
fuse of the correct amperage by using the
fuse puller on the reverse side of the cap.
WARNING
EWJ00800
Do not use fuses of higher amperage than
recommended. Substitution with a fuse
that has an improper rating can cause ex-
tensive electrical system damage and pos-
sible fire.
EJU34710Towing the watercraft
If the watercraft becomes inoperative in the
water, it can be towed to shore.
If the watercraft must be towed in an emer-
gency using a towline, the operator should
ride the watercraft, holding onto the handle-
bars.
CAUTION:
ECJ00720
Tow the watercraft at 5 mph (8 km/h) or
less, otherwise water could enter the en-
gine through the exhaust passages or
through the air intake and flood the en-
gine compartment if it is towed too fast.
Tow the watercraft using the bow eye
only.
1Electrical box
2Cap
3Fuse puller
4Fuse
5Spare fuse
Fuse amperage:
Main fuse:
20 A
Meter fuse:
3 A
Bilge pump fuse:
3 A
UF1G74E0.book Page 78 Monday, July 31, 2006 10:10 AM
Page 86 of 90
Trouble recovery
79
The bow must be kept up out of the wa-
ter during towing to prevent water from
entering the engine compartment.
WARNING
EWJ00810
The watercraft should only be towed in
an emergency.
The towline should be long enough so
that the watercraft will not collide with
the towing boat when slowing down. A
good rule of thumb is a towline that is
three times the combined length of the
towing boat and the watercraft.
The operator of the towing boat must
keep speed to a minimum and avoid traf-
fic or obstacles which could be a hazard
to the rider on the watercraft.
EJU34740Submerged watercraft
If the watercraft is submerged or flooded with
water, follow the procedure below and consult
a Yamaha dealer as soon as possible. Failure
to do so could result in serious engine dam-
age!
In an emergency:
(1) Beach the watercraft and remove the
stern drain plugs to drain the water fromthe engine compartment. (See page 39
for more information.)
Remove the storage compartment drain
plugs to drain the water from each stor-
age compartment.
(2) Install the stern drain plugs.
(3) Have the watercraft inspected by a
Yamaha dealer as soon as possible.
1Bow eye
UF1G74E0.book Page 79 Monday, July 31, 2006 10:10 AM