wheel YAMAHA GRIZZLY 450 2012 Owners Manual

Adjusting the rear brake lever and brake pedal free play, and the brake
pedal height ............................................ 8-41
Axle boots ................................................ 8-46
Brake light switches ................................. 8-47
Checking and lubricating the cables ........ 8-47
Checking and lubricating the front and rear brake levers .................................... 8-48
Checking and lubricating the brake pedal ...................................................... 8-48
Checking the wheel hub bearings ............ 8-49
Lubricating the drive shaft universal joint ......................................................... 8-49
Checking the stabilizer bushes ................ 8-50
Lubricating the rear knuckle pivots ........... 8-50
Lubricating the steering shaft ................... 8-51
Battery ...................................................... 8-51
Replacing a fuse ...................................... 8-54
Replacing a headlight bulb ....................... 8-55
Adjusting a headlight beam ...................... 8-57
Replacing the tail/brake light bulb ............ 8-57
Removing a wheel .................................... 8-59
Installing a wheel ...................................... 8-59
Troubleshooting ....................................... 8-61
Troubleshooting charts ............................. 8-62 CLEANING AND STORAGE ..........................9-1
Cleaning ......................................................9-1
Storage .......................................................9-2
SPECIFICATIONS .......................................10-1
CONSUMER INFORMATION.......................11-1 Identification numbers ...............................11-1
U1CT61E0.book Page 3 Wednesday, April 20, 2011 6:36 PM

1-4
1
37S-F816N-00< 0.5 kg
( 1 lb )
37S-F816S-00
YAMAHA MOTOR CO., LTD.
2500 SHINGAI, IWATA, JAPAN YFM450FWAD
19.4 kW
281 kg
2011
1CT-F155A-20
YAMAHA MOTOR CO., LTD.
2500 SHINGAI, IWATA, JAPANYFM450FWAD
19.4 kW
284 kg
2011
1CT-F155A-30
9
10 11 YFM45FGPB (panel wheel model)
YFM45FGPHB
11 YFM45FGPB (cast wheel model)U1CT61E0.book Page 4 Wednesday, April 20, 2011 6:36 PM

2-1
2
EBU17431
SAFETY INFORMATION
EBU17504AN ATV IS NOT A TOY AND CAN BE HAZARD-OUS TO OPERATE.An ATV handles differently from other vehicles, in-
cluding motorcycles and cars. A collision or roll-
over can occur quickly, even during routine
maneuvers such as turning and riding on hills or
over obstacles, if you fail to take proper precau-
tions.
SEVERE INJURY OR DEATH can result if you do
not follow these instructions:
Read this manual and all labels carefully and fol-
low the operating procedures described.
Never operate an ATV without proper training or
instruction.
Always follow the age recommendation:
– A child under 16 years old should never oper-
ate an ATV with engine size greater than 90 cc.
Never allow a child under age 16 to operate an
ATV without adult supervision, and never allow
continued use of an ATV by a child if he or she
does not have the abilities to operate it safely.

Never carry a passenger on an ATV.
Always avoid operating an ATV on any paved
surfaces, including sidewalks, driveways, park-
ing lots and paved streets.
Never operate an ATV on any paved street,
paved road or motorway.
Watch carefully for other vehicles when operat-
ing on unpaved public streets or roads. Make
sure you know your country ’s laws and regula-
tions before you ride on unpaved public streets
or roads.
Never operate an ATV without wearing an ap-
proved motorcycle helmet that fits properly. You
should also wear eye protection (goggles or face
shield), gloves, boots, a long-sleeved shirt or a
jacket, and long pants.
Never consume alcohol or drugs before or while
operating this ATV.
Never operate at speeds too fast for your skills
or the riding conditions. Always go at a speed
that is proper for the terrain, visibility, operating
conditions, and your experience.
Never attempt wheelies, jumps, or other stunts.
U1CT61E0.book Page 1 Wednesday, April 20, 2011 6:36 PM

3-2
3
EBU17712Controls and instruments
TIPThe ATV you have purchased may differ slightly
from the figures shown in this manual.
1. Rear brake lever
2. Handlebar switches
3. Starter (choke)
4. Horn switch
5. Drive select lever
6. Multi-function display
7. Main switch
8. Auxiliary DC jack
9. Fuel tank cap
10.On-Command four-wheel-drive/differential gear lock switch
11.Throttle lever
12.Front brake lever
13.Front storage compartment
9
54
13121110
2
13 678
U1CT61E0.book Page 2 Wednesday, April 20, 2011 6:36 PM

4-2
4
EBU26695Indicator lights and warning lights
EBU17990Low-range indicator light“”
This indicator light comes on when the transmis-
sion is in the low-range position.EBU17980High-range indicator light “”
This indicator light comes on when the transmis-
sion is in the high-range position.EBU17860Neutral indicator light “”
This indicator light comes on when the transmis-
sion is in the neutral position.
1. On-Command differential gear lock indicator light “DIFF. LOCK ”
2. Low-range indicator light “L”
3. High-range indicator light “H”
4. Neutral indicator light “N”
5. Reverse indicator light “R”
6. Park indicator light “P”
7. On-Command four-wheel-drive/differential gear lock indicator “”/“”
8. Coolant temperature warning light “”
1. Electric Power Steering warning light “EPS”
EPS
1
U1CT61E0.book Page 2 Wednesday, April 20, 2011 6:36 PM

4-4
4
TIP
If the engine is stopped using the engine stop
switch and the key is in the “ON ” position, the
EPS warning light comes on to indicate that the
power assistance for the steering is not function-
ing.
If the steering load is too heavy (i.e., excessive
steering use when the ATV is traveling at a slow
speed), the power assist is reduced to protect
the EPS motor from overheating.EBU29621On-Command four-wheel-drive indicator “”,
On-Command differential gear lock
indicator “” and indicator light “DIFF.
LOCK”
The On-Command four-wheel-drive indicator “”
comes on when the On-Command four-wheel-
drive switch is set to the “4WD ” position.
The On-Command differential gear lock
indicator “” and the On-Command differential
gear lock indicator light “DIFF. LOCK ” come on
when the On-Command differential gear lock
switch is set to the “LOCK ” position.
TIP
Due to the synchronizing mechanism in the dif-
ferential gear case, the four-wheel-drive indica-
tor may not come on until the ATV starts moving.
When the On-Command differential gear lock
switch is set to “LOCK ”, the indicator “” and
the indicator light “DIFF. LOCK ” will flash until
the differential gear is locked. If the indicator and
the indicator light continue to flash, the differen-
tial is not locked. In this case, start moving to al-
low time for the differential to lock.
U1CT61E0.book Page 4 Wednesday, April 20, 2011 6:36 PM

4-8
4
switch to override the differential gear lock speed
limiting function. (See page 4-9.) Releasing the
switch restores the speed limiting function.
While the override switch is pushed, the segments
of the speedometer digits will appear as shown in
the figure.
TIPIf the digits of the speedometer appear as shown
when the switch is NOT being pushed, this could
indicate a malfunction in the electrical system. In
this case, take the ATV to a Yamaha dealer at the
first opportunity.
WARNING
EWB00150Always ride at a slow speed when the ATV is in
four-wheel-drive differential gear lock, and al-
low extra time and distance for maneuvers.
All wheels turn at the same speed when the dif-
ferential is locked, so it takes more effort to
turn the ATV. The effort needed to turn increas-
es with the riding speed. You may lose control
and have an accident if you cannot make a
sharp enough turn for the speed you are trav-
eling.EBU26606On-Command four-wheel-drive switch
“
2WD ”/“ 4WD ”
WARNING
EWB00163Always stop the ATV before changing from
two-wheel drive to four-wheel drive and vice
versa. The ATV handles differently in two-
wheel drive than in four-wheel drive in some
circumstances. Changing from two-wheel
drive to four-wheel drive or vice versa while
moving may cause the ATV to unexpectedly
U1CT61E0.book Page 8 Wednesday, April 20, 2011 6:36 PM

4-9
4handle differently. This could distract the oper-
ator and increase the risk of losing control and
of causing an accident.
This ATV is equipped with a switch to change from
two-wheel drive to four-wheel drive and vice versa.
Select the appropriate drive according to the ter-
rain and the conditions.
“
2WD ” (two-wheel drive): Power is supplied to
the rear wheels.
“ 4WD ” (four-wheel drive): Power is supplied to
the rear and front wheels.
To change from two-wheel drive to four-wheel
drive, stop the ATV and push the switch in to the
“ 4WD ” position. Then, the four-wheel-drive
indicator “” comes on in the multi-function dis-
play.
To change from four-wheel drive to two-wheel
drive, stop the ATV and push the switch in to the
“ 2WD ” position.
EBU18255On-Command differential gear lock switch
“ 4WD ”/“ LOCK ”
WARNING
EWB00131Always stop the ATV before changing from
four-wheel drive to four-wheel-drive differen-
tial gear lock or vice versa.
The ATV handles differently in four-wheel drive
than in differential gear lock in some circum-
stances. Changing from four-wheel drive to dif-
ferential gear lock or vice versa while moving
may cause the ATV to handle differently unex-1. On-Command four-wheel-drive switch “2WD”/“4WD ”
U1CT61E0.book Page 9 Wednesday, April 20, 2011 6:36 PM

4-10
4
pectedly. This could distract the operator and
increase the risk of losing control and causing
an accident.
WARNING
EWB00140Always ride at a slow speed when the ATV is in
differential gear lock, and allow extra time and
distance for maneuvers.
All wheels turn at the same speed when the dif-
ferential gear is locked, so it takes more effort
to turn the ATV. The effort needed to turn in-
creases with the riding speed. You may lose
control and have an accident if you cannot
make a sharp enough turn for the speed you
are traveling.This ATV is equipped with a switch allowing you to
lock the differential gear when in four-wheel drive.
Select the appropriate switch position according to
the terrain and the conditions.
“
4WD ” (four-wheel drive): Power is supplied to
the rear and front wheels.

“ LOCK ” (four-wheel drive with the differential
gear locked): Power is supplied to the rear and
front wheels and the differential gear is locked.
Unlike in four-wheel drive, all wheels turn at the
same speed.
To lock the differential gear in four-wheel drive,
make sure the On-Command four-wheel-drive
switch is pushed in to the “4WD ” position.1. On-Command four-wheel-drive switch “2WD ”/“4WD ”
2. On-Command differential gear lock switch “4WD”/“LOCK ”
U1CT61E0.book Page 10 Wednesday, April 20, 2011 6:36 PM

4-11
4Stop the ATV, move the differential gear lock lever
to position (a), and then push the differential gear
lock switch in to the “LOCK ” position. When the dif-
ferential gear is locked, the differential gear lock in-
dicator light “ DIFF. LOCK” will come on along with
the indicator “” in the multi-function display. To release the differential gear lock, stop the ATV
and push the switch to the
“4WD ” position.
TIP
When the switch is set to “LOCK ”, the differential
gear lock indicator and indicator light will flash
until the differential gear is locked.
When the indicator and indicator light are flash-
ing, turning the handlebar back and forth will
help the differential gear lock to engage.
1. Differential gear lock lever
2. On-Command four-wheel-drive switch “2WD”/“4WD ”
1. On-Command differential gear lock switch “4WD”/“LOCK ”
U1CT61E0.book Page 11 Wednesday, April 20, 2011 6:36 PM