oil level YAMAHA TT600RE 2004 Service Manual

SPECMAINTENANCE SPECIFICATIONS
2-12
Item Standard Limit
Steering
Steering bearing type Taper roller bearing
Lock to lock angle (left) 45° •••
Lock to lock angle (right) 45° •••
Front suspension
Front fork travel 277 - 283 mm •••
Fork spring free length 530 mm •••
Spring rate (K1) 7.0 N/mm (0.71 kgf/mm) •••
Spring stroke (K1) 330 mm •••
Spring rate (K2) 11.2 N/mm (1.14 kgf/mm) •••
Optional spring available No
Recommended oil Liqui Moly Racing suspension oil SAE 7,5
Quantity 650 cc •••
Level 180 mm •••
< min - max > 170-190 mm (from upper edge of inner •••
tube, fully compressed without spring)
Rear suspension
Rear shock absorber assembly travel 83 mm
Spring free length 224 mm •••
Installed length 211 mm ± 1.5 mm
Spring rate (K) 80 N/mm (8.1 kgf/mm) •••
Optional spring available No
Swingarm
Free play limit (at the end of
the swingarm)-radial ••• 1.0 mm
Free play limit (at the end of
the swingarm)-axial 0.4 - 0.7 mm •••
Front wheel
Wheel type Spoke wheel
Rim size 21 x 1.85
Rim material Aluminium
Max. radial wheel runout 1.0 mm •••
Max. lateral wheel runout 0.5 mm •••
Rear wheel
Wheel type Spoke wheel
Rim size 18 x MT2.50
Rim material Aluminium
Max. radial wheel runout 1.0 mm •••
Max. lateral wheel runout 0.5 mm •••
CHASSIS
ProCarManuals.com

INSP
ADJ
CHAPTER 3.
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION..........................................................................................................3-1
PERIODIC MAINTENANCE/LUBRICATION INTERVALS........................................3-1
SEAT, FUEL TANK AND REAR COWLING................................................................3-3
REMOVAL ............................................................................................................3-3
INSTALLATION ....................................................................................................3-3
ENGINE........................................................................................................................3-4
VALVE CLEARANCE ADJUSTMENT ..................................................................3-4
DRIVE CHAIN ADJUSTMENT ..............................................................................3-7
IDLE SPEED ADJUSTMENT ................................................................................3-7
THROTTLE CABLE FREE PLAY ADJUSTMENT ................................................3-8
SPARK PLUG INSPECTION ................................................................................3-9
IGNITION TIMING CHECK ................................................................................3-11
COMPRESSION INSPECTION ..........................................................................3-12
ENGINE OIL LEVEL CHECK ..............................................................................3-15
ENGINE OIL REPLACEMENT ............................................................................3-17
ENGINE OIL PRESSURE CHECK ....................................................................3-21
CLUTCH ADJUSTMENT ....................................................................................3-21
AIR FILTER CLEANING ......................................................................................3-24
FUEL FILTER CLEANING ..................................................................................3-25
ENGINE OIL TANK FILTER CLEANING ............................................................3-26
SUCTION HOSE AND MANIFOLD INSPECTION..............................................3-28
FUEL LINE INSPECTION ..................................................................................3-28
CRANKCASE VENTILATION HOSE INSPECTION ..........................................3-29
EXHAUST SYSTEM INSPECTION ....................................................................3-29
CHASSIS....................................................................................................................3-30
ADJUSTING THE FRONT BRAKE ....................................................................3-30
ADJUSTING THE REAR BRAKE ......................................................................3-31
CHECKING THE BRAKE FLUID LEVEL ............................................................3-32
BRAKE PAD WEAR INSPECTION ....................................................................3-33
BRAKE HOSING INSPECTION ..........................................................................3-33
BRAKE CIRCUIT BLEEDING ............................................................................3-34
DRIVE CHAIN SLACK INSPECTION AND ADJUSTMENT..................................3-35
DRIVE CHAIN LUBRICATION ............................................................................3-36
FRONT FORK INSPECTION ..............................................................................3-37
ADJUSTING THE FRONT FORK ......................................................................3-37
REAR SHOCK ABSORBER ADJUSTMENT ......................................................3-38
STEERING INSPECTION ..................................................................................3-40
TYRE INSPECTION ............................................................................................3-41
WHEEL INSPECTION ........................................................................................3-44
SPOKE INSPECTION AND TIGHTENING ........................................................3-44
CABLE INSPECTION..........................................................................................3-45
LEVER AND PEDAL LUBRICATION ..................................................................3-45
SIDESTAND LUBRICATION ..............................................................................3-46
REAR SUSPENSION LUBRICATION ................................................................3-46
ProCarManuals.com

INSP
ADJINTRODUCTION/PERIODIC MAINTENANCE/
LUBRICATION INTERVALS
3-1
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION
This chapter includes all information necessary to perform recommended inspections and adjustments.
These preventive maintenance procedures, if followed, will ensure more reliable vehicle operation and a
longer service life. The need for costly overhaul work will be greatly reduced. This information applies to
vehicles already in service as well as to new vehicles that are being prepared for sale. All service techni-
cians should be familiar with this entire chapter.
PERIODIC MAINTENANCE/LUBRICATION INTERVALS
ODOMETER READING (x 1,000 km)
ANNUAL N0. ITEM CHECK OR MAINTENANCE JOB
110 2030 40CHECK
1
*Fuel line• Check fuel hoses for cracks or damage. ✓✓ ✓✓ ✓•
• Check condition.
✓✓
2 Spurk plug• Clean and regap.
• Replace.✓✓
3 * Valves• Check valve clearance.
✓✓ ✓✓
• Adjust.
4Air filter element• Clean.✓✓
• Replace. ✓✓
5 Clutch• Check operation.
✓✓ ✓ ✓✓
• Adjust.
• Check operation, fluid level and vehicle for fluid leakeage.
6 * Front brake•(See NOTE). ✓✓ ✓ ✓✓ ✓•
• Replace brake pads. Whenever worm to the limit
• Check operation, fluid level and vehicle
•for fluid leakage. ✓✓ ✓ ✓✓ ✓
7 * Rear brake•(See NOTE).
• Replace brake pads. Whenever worm to the limit
8 * Brake hoses• Check for cracks or damage.✓✓✓✓ ✓• Replace. (See NOTE). Every 4 years
9 * Wheels• Check runout, spoke tightness and for damage.
✓✓✓ ✓
• Tighten spokes if necessary.
• Check tread depth and for damage.
10 * Tyres• Replace if necessary.
✓✓✓✓ ✓
• Check air pressure.
• Correct if necessary.
11 * Wheel bearings• Check bearing for looseness or damage.✓✓✓✓
12 * Swingarm• Check operation and for excessive play.✓✓✓✓
• Check chain slack.
13 * Drive chain• Make sure that the rear wheel is properly aligned.Every 500 km and after washing the
• Clean and lubricate.motorcycle or riding in the rain.
14 *Steering • Check bearing play and steering for roughness. ✓✓ ✓ ✓✓bearings
• Lubrificate with lithium-soap-based grease. Every 20,000 km
15 *Chassis • Make sure that all nuts, bolts and screws are properly
✓✓ ✓✓ ✓
fasteners•tightened.
16Sidestand• Check operation.
✓✓ ✓✓ ✓
• Lubricate.
17
*Sidestand
• Check operation and for oil leakage. ✓✓ ✓ ✓✓ ✓
switch
ProCarManuals.com

INTRODUCTION/PERIODIC MAINTENANCE/
LUBRICATION INTERVALS
3-2
INSP
ADJ
ODOMETER READING (x 1,000 km)
ANNUAL N0. ITEM CHECK OR MAINTENANCE JOB
110 2030 40CHECK
18 * Rear brake• Check operation, fluid level and vehicle for fluid leakage. ✓✓✓ ✓
Rear shock
• Check operation and shock absorber for oil leakage.
19
*absorber ✓✓✓ ✓
assemblysull’ammortizzatore.
Rear suspension
• Check operation.
✓✓✓ ✓
20*
relay arm and
connecting arm
• Lubricate with lithium-soap-based grease.
✓✓
pivoting points
• Check starter (choke) operation.
21 * Carburator
• Adjust engine idling speed.✓✓ ✓✓ ✓ ✓
22 Engine oil• Change.
✓✓ ✓✓ ✓ ✓
• Check oil level and oil leakage.
23Engine oil filter
• Replace.✓✓✓
element
24 *Front and rear •
brake switches• Check operation.✓✓ ✓✓ ✓ ✓
Moving parts
25
and cables• Lubricate. ✓✓✓ ✓ ✓
Throttle grip • Check operation and free play.
26 * housing and • Adjust the throttle cable free play if necessary.
✓✓✓ ✓ ✓
cable • Lubricate the throttle grip housing and cable.
27 *Muffler and
• Check the screw clamp for looseness. ✓
exhaust pipe
28 *Lights, signals • Check operation.
✓✓ ✓✓ ✓ ✓
and switches• Adjust headlight beam.
* Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools,
data and technical skills.
NOTE:
• The annual checks must be performed every year, except if a kilometer-based maintenance is per-
formed instead.
• From 50,000 km, repeat the maintenance intervals starting from 10,000 km.
• The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
• Hydraulic brake system:
• Check the brake fluid level regularly and fill as required.
• Replace the oil seals on the inner parts of the master cylinder and caliper cylinder every two years.
• Replace the brake hoses every four years or if cracked or damaged.
ProCarManuals.com

INSP
ADJ
3-15
ENGINE OIL LEVEL CHECK
ENGINE OIL LEVEL CHECK
Do not put additives into the engine oil. The
latter also lubricates the clutch and additives
might cause it to slide.
WARNING
Never remove the oil tank cap when the
engine is hot. The boiling oil might spill over,
causing burns. Wait for the oil to cool to at
least 60°C (140°F) or thereabouts.
This model is fitted with a dry crankcase lubrica-
tion system. A feed pump delivers oil to the en-
gine; after fully lubricating the latter, the oil is re-
turned to the tank by a scavenge pump. The oil
level must therefore be checked in the oil tank.
1. Start the engine and warm up until the oil tem-
perature rises to approximately 60°C (140°F).
2. Idle the engine for at least 10 seconds while
keeping the motorcycle upright. After stop the
engine and check the oil level through the
level window (3) located on the left side of the
oil tank assy and(or) by oil level gauge.
NOTE:
Be sure the motorcycle is positioned straight up
when checking the oil level. A slight tilt toward the
side can result in false readings.
3. The oil level should be between the maximum
(1) and minimum (2) marks.
CAUTION:
ProCarManuals.com

3-16
INSP
ADJ
ENGINE OIL LEVEL CHECK
If the oil level is below minimum ➔Add oil up
to maximum level.
Recommended oil:
SAE20W40SE or SAE10W30SE
Refer to the chart for selection of
the oils suited to the atmospheric
temperature.
API Standard:
API SE, SF, SG or higher grade
•Do not put in any chemical additives or use
oils with a grade of CD (a) or higher.
•Be sure not to use oils labeled “ENERGY
CONSERVING II” (b) or higher. Engine oil
also lubricates the clutch and additives
could cause clutch slippage.
•Be sure no foreign material enters the
crankcase.
4. Reassemble the oil tank cap.
Never start the engine when the oil tank is
empty.
CAUTION:
CAUTION:
Oil capacity:
Total:
3.0 litres
Periodic oil change:
2.4 litres
With oil filter change:
2.5 litres
ProCarManuals.com

3-18
INSP
ADJ
ENGINE OIL REPLACEMENT
Fastening torques:
Drain plug (engine):
30 Nm (3.0 mkg)
Oil tank hose (flange):
10 Nm (1.0 mkg)
Oil filter cover air bleeder screw:
5 Nm (0.5 mkg)
9. Fill:
•Oil tank
Recommended oil:
SAE20W40SE or SAE10W30SE
Refer to the chart for selection of
the oils suited to the atmospheric
temperature.
API Standard:
API SE, SF, SG or higher grade
Oil capacity:
Periodic change = 2.4 litres
•Do not put in any chemical additives or
use oils with a grade of CD (a) or higher.
•Be sure not to use oils labeled “ENERGY
CONSERVING II” (b) or higher. Engine oil
also lubricates the clutch and additives
could cause clutch slippage.
•Be sure no foreign material enters the
crankcase.
CAUTION:
10. Install:
•Oil tank tap
11. Check:
•Oil level
See section “ENGINE OIL LEVEL
CHECK”.
•Oil pressure
See section “ENGINE OIL PRESSURE
CHECK”.
•Oil leakage
ProCarManuals.com

3-20
INSP
ADJ
ENGINE OIL REPLACEMENT
Recommended oil:
SAE20W40SE or SAE10W30SE
Refer to the chart for selection of
the oils suited to the atmospheric
temperature.
API Standard:
API SE, SF, SG or higher grade
Oil capacity:
Total:
3.0 litres
Periodic oil change:
2.4 litres
With oil filter change:
2.5 litres
•Do not put in any chemical additives or use
oils with a grade of CD (a) or higher.
•Be sure not to use oils labeled “ENERGY
CONSERVING II” (b) or higher. Engine oil
also lubricates the clutch and additives
could cause clutch slippage.
•Be sure no foreign material enters the
crankcase.
CAUTION:
12. Install:
•Oil tank cap
13. Check:
•Oil level
See section “ENGINE OIL LEVEL
CHECK”.
•Oil pressure
See section “ENGINE OIL PRESSURE
CHECK”.
•Oil leakage 11. Fill:
•Oil tank
ProCarManuals.com

CHECKING THE BRAKE FLUID LEVEL
3-32
INSP
ADJ
CHECKING THE BRAKE FLUID LEVEL
1. Stand the motorcycle on a level surface.
NOTE:
•Place the motorcycle on a suitable stand.
•Make sure that the motorcycle is upright.
2. Check:
•Brake fluid level
Below the minimum level mark a➔Add
the recommended brake fluid to the prop-
er level.
[A] Front brake
[B] Rear brake
WARNING
•Use only the designated brake fluid. Other
brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.
•Refill with the same type of brake fluid that
is already in the system. Mixing brake flu-
ids may result in a harmful chemical reac-
tion, leading to poor brake performance.
•When refilling, be careful that water does
not enter the reservoir. Water will signifi-
cantly lower the boiling point of the brake
fluid and could cause vapor lock.
Brake fluid may damage painted surfaces and
plastic parts. Therefore, always clean up any
spilt brake fluid immediately.
NOTE:
In order to ensure a correct reading of the brake
fluid level, make sure that the top of the reservoir
is horizontal.
CAUTION:
Recommended brake fluid:
DOT4





ProCarManuals.com

INSP
ADJFRONT FORK INSPECTION/
FRONT FORK ADJUSTMENT
3-37
 


FRONT FORK INSPECTION
WARNING
When inspecting the front fork, hold the
motorcycle firmly to prevent it falling over.
1. Place the motorcycle on a level surface.
2. Check:
•Inner tube
Scratches/Damage ➔Replace.
•Oil seal
Undue oil leakage ➔Replace.
3. With the motorcycle in a level upright position
operate the front brake.
4. Check:
•Proper functioning
Compress and release the front fork sev-
eral times.
Irregular/jerky functioning ➔Repair.
See section “FRONT FORK” in Chapter 4.
ADJUSTING THE FRONT FORK
This front fork is equipped with spring pre-load ad-
justing bolts.
WARNING0
Always adjust both fork legs equally, other-
wise poor handling and loss of stability may
result.
Adjust the spring preload as follows.
To increase the spring preload and thereby hard-
en the suspension, turn the adjusting bolt on each
fork leg in direction a. To decrease the spring
preload and thereby soften the suspension, turn
the adjusting bolt on each fork leg in direction b.
Setting
Minimum (soft) 1-2-3
Standard 4
Maximum (hard) 5-6-7-8-9-10
ProCarManuals.com