brake YAMAHA XJ600S 2000 Owner's Manual

R
6-32
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
3. Install the wheel axle and let the
motorcycle down.
4. Install the calipers and caliper
bolts. Make sure there is enough
gap between the brake pads be-
fore installing the calipers onto the
brake discs.
5. Push down hard on the handle-
bars several times to check for
proper fork operation.
6. Tighten the wheel axle, pinch bolt
and caliper bolts to the specified
torque.7. Install the speedometer cable.Tightening torque:
Wheel axle:
58 Nm (5.8 mákg)
Pinch bolt:
40 Nm (4.0 mákg)
Caliper bolt:
19 Nm (1.9 mákg)

L
6-33
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
1. Axle nut
EAU01480
Rear wheel removal
EW000122
lIt is advisable to have a Yamaha
dealer service the wheel.
lSecurely support the motor-
cycle so there is no danger of it
falling over.
1. Place the motorcycle on the cen-
terstand.
2. Remove the axle nut.
1. Brake torque rod bolt
2. Nut
3. Remove the brake torque rod bolt
by removing the nut.
4. While supporting the brake cali-
per, pull out the wheel axle.
5. Push the wheel forward and re-
move the drive chain.
6. Remove the wheel assembly.
NOTE:
lDo not depress the brake pedal
when the disc and caliper are sep-
arated.
lYou do not have to disassemble
the chain in order to remove or in-
stall the rear wheel.

R
6-34
PERIODIC MAINTENANCE AND MINOR REPAIR
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-6.frame
EAU01468
Rear wheel installation
1. Install the wheel assembly and in-
sert the axle.
2. Install and adjust the drive chain.
(See page 6-20 for details about
adjusting the drive chain slack.)
3. Install the axle nut.
4. Install the caliper and caliper bolts.
Make sure there is enough gap
between the brake pads before in-
stalling the caliper onto the brake
disc.
5. Take the motorcycle off the cen-
terstand.
6. Tighten the axle nut and brake
torque rod bolt to the specified
torques.
Tightening torque:
Axle nut:
105 Nm (10.5 mákg)
Brake torque rod bolt:
23 Nm (2.3 mákg)
EAU01008
Troubleshooting
Although Yamaha motorcycles receive
a rigid inspection before shipment from
the factory, trouble may occur during
operation.
Any problem in the fuel, compression,
or ignition systems can cause poor
starting and loss of power. The trouble-
shooting chart describes a quick, easy
procedure for making checks.
If your motorcycle requires any repair,
bring it to a Yamaha dealer. The skilled
technicians at a Yamaha dealership
have the tools, experience, and know-
how to properly service your motor-
cycle. Use only genuine Yamaha parts
on your motorcycle. Imitation parts may
look like Yamaha parts, but they are of-
ten inferior. Consequently, they have a
shorter service life and can lead to ex-
pensive repair bills.

R
7-2
MOTORCYCLE CARE AND STORAGE
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-7.frame
ECA00010
CAUTION:
lAvoid using strong acidic wheel
cleaners, especially on spoked
wheels. If you do use such
products for hard-to-remove
dirt, do not leave it on any long-
er than instructed, then thor-
oughly rinse it off with water,
immediately dry the area and
apply a corrosion protection
spray.
lImproper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.
lDo not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
lDo not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel bearings,
swingarm bearings, forks and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
lFor motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure they do not
leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads in the winter are extremely corro-
sive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads. (Salt sprayed in the
winter may remain on the roads well
into spring.)

L
7-3
MOTORCYCLE CARE AND STORAGE
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-7.frame
1. Clean your motorcycle with cold
water and soap after the engine
has cooled down.
ECA00012
CAUTION:
Do not use warm water since it in-
creases the corrosive action of the
salt.
2. Be sure to apply a corrosion pro-
tection spray on all (even chrome-
and nickel-plated) metal surfaces
to prevent corrosion.After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all (even chrome-
and nickel-plated) metal surfaces.
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
before storing it or covering it.
EWA00001
Make sure that there is no oil or wax
on the brakes and tires. If neces-
sary, clean the brake discs and lin-
ings with a regular brake disc
cleaner or acetone, and wash the
tires with warm water and mild soap.
Then, carefully test the motorcycle
for its braking performance and cor-
nering behavior.

L
8-3
SPECIFICATIONS
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-8.frame
Maximum load*
XJ600S 184 kg
XJ600N 187 kg
Air pressure (cold tire)
Up to 90 kg load*
Front 200 kPa (2.00 kg/cm
2, 2.00 bar)
Rear 225 kPa (2.25 kg/cm
2, 2.25 bar)
90 kg load ~ maximum load*
Front 200 kPa (2.00 kg/cm
2, 2.00 bar)
Rear 250 kPa (2.50 kg/cm
2, 2.50 bar)
High speed riding
Front 200 kPa (2.00 kg/cm
2, 2.00 bar)
Rear 250 kPa (2.50 kg/cm
2, 2.50 bar)
* Load is total weight of cargo, rider, passenger and accessories.
Wheels
Front
Ty p e C a s t
Size 17 ´ MT 2.50
Rear
Ty p e C a s t
Size 18 ´ MT 3.50Brakes
Front
Type Dual disc brake
Operation Right hand operation
Fluid DOT 4 or DOT 3
Rear
Type Single disc brake
Operation Right foot operation
Fluid DOT 4 or DOT 3
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm (monocross suspension)
Shock absorbers
Front Coil spring/oil damper
Rear Coil spring/gas-oil damper
Wheel travel
Front 140 mm
Rear 110 mm
Electrical systems
Ignition system T.C.I. (digital)

R
8-4
SPECIFICATIONS
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/E-8.frame
Charging system
Type A.C. magneto
Standard output 14 V, 20 A @ 5,000 r/min
Battery
Type YTX9-BS, GTX9-BS
Voltage, capacity 12 V, 8 AH
Headlight typeQuartz bulb (halogen)
Bulb voltage, wattage ´
quantity
Headlight 12 V, 60/55 W ´ 1
Auxiliary light 12 V, 4 W ´ 1 (except for GB, IRL)
12 V, 3.4 W ´ 1 (for GB, IRL)
Tail/brake light 12 V, 5/21 W ´ 1
Turn signal light 12 V, 21 W ´ 4
Meter light
XJ600S 12 V, 1.7 W ´ 3
XJ600N 14 V, 3 W ´ 2
12 V, 1.7 W ´ 2
Neutral indicator light 12 V, 3.4 W ´ 1
High beam indicator light 12 V, 3.4 W ´ 1
Oil level indicator light
XJ600S 12 V, 3.4 W ´ 1
XJ600N 14 V, 3 W ´ 1
Turn indicator light 12 V, 3.4 W ´ 2Fuses
Main fuse 30 A
Ignition fuse 10 A
Signaling system fuse 15 A
Headlight fuse 15 A
Hazard light fuse 10 A

L
INDEX
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/EEIX.frame
A
Air filter .................................................6-10
B
Battery ..................................................6-25
Brake and clutch lever lubrication ........6-23
Brake and shift pedal lubrication ..........6-22
Brake fluid replacement ........................6-20
Brake light switch adjustment ...............6-17
C
Cable inspection and lubrication ..........6-22
Carburetor adjustment ..........................6-11
Care ........................................................7-1
Center and sidestand lubrication ..........6-23
Checking the front and rear brake
pads ...................................................6-18
Clutch lever ............................................3-9
Clutch lever free play adjustment .........6-15
Controls/Instruments (XJ600N) ..............2-6
Controls/Instruments (XJ600S) ..............2-3
D
Dimmer switch ........................................3-7
Drive chain lubrication ..........................6-21
Drive chain slack adjustment ................6-21
Drive chain slack check ........................6-20
E
Engine break-in ......................................5-5
Engine oil ................................................6-7
Engine stop switch .................................3-9
F
Front brake lever ................................. 3-10
Front fork inspection ............................ 6-24
Front wheel installation ........................ 6-31
Front wheel removal ............................ 6-31
Fuel ...................................................... 3-12
Fuel cock ............................................. 3-13
Fuel tank breather hose
(for Germany only) ............................ 3-12
Fuel tank cap ....................................... 3-11
Fuse replacement ................................ 6-26
G
Give safety the right of way ................... 1-1
H
Handlebar switches ............................... 3-7
Dimmer switch ................................. 3-7
Engine stop switch ........................... 3-9
Hazard switch .................................. 3-8
Horn switch ...................................... 3-8
Lights switch .................................... 3-9
Pass switch ...................................... 3-7
Start switch ...................................... 3-9
Turn signal switch ............................ 3-8
Hazard switch ........................................ 3-8
Headlight bulb replacement
(for XJ600N) ...................................... 6-29
Headlight bulb replacement
(for XJ600S) ...................................... 6-27
Helmet holders ..................................... 3-15
High beam indicator light ....................... 3-3
Horn switch ............................................ 3-8
I
Identification number records ................ 9-1
Idle speed adjustment .......................... 6-12
Indicator lights ........................................ 3-3
High beam indicator light .................. 3-3
Neutral indicator light ....................... 3-3
Oil level indicator light ...................... 3-3
Turn indicator lights .......................... 3-3
Inspecting the brake fluid level ............ 6-19
K
Key identification number
(for XJ600N) ........................................ 9-1
Key identification number
(for XJ600S) ........................................ 9-1
L
Left view (XJ600N) ................................ 2-4
Left view (XJ600S) ................................. 2-1
Lights switch .......................................... 3-9
Luggage strap holders ......................... 3-16
M
Main switch ............................................ 3-1
Model label ............................................ 9-2
N
Neutral indicator light ............................. 3-3

R
INDEX
/Net/layout8/layout_G2/work/Imai_work/OM-PS/AA9156_XJ600SN-E6/English/EEIX.frame
O
Oil level indicator circuit check .............. 3-5
Oil level indicator light ............................ 3-3
P
Panel A .................................................. 6-5
Panel removal and installation ............... 6-5
Parking .................................................. 5-6
Pass switch ............................................ 3-7
Periodic maintenance and lubrication .... 6-2
Pre-operation check list ......................... 4-1
R
Rear brake pedal ................................. 3-11
Rear brake pedal height adjustment .... 6-17
Rear shock absorber adjustment ......... 3-15
Rear suspension lubrication ................ 6-23
Rear wheel installation ........................ 6-34
Rear wheel removal ............................. 6-33
Recommended shift points
(for Switzerland only) .......................... 5-5
Right view (XJ600N) .............................. 2-5
Right view (XJ600S) .............................. 2-2
S
Seat ..................................................... 3-14
Shift pedal ............................................ 3-10
Shifting ................................................... 5-4
Sidestand ............................................. 3-17
Sidestand/clutch switch operation
check ................................................. 3-17
Spark plug inspection ............................ 6-6
Specifications ......................................... 8-1
Speedometer (for XJ600N) .................... 3-6
Speedometer (for XJ600S) .................... 3-6
Start switch ............................................ 3-9
Starter (choke) Ò Ó ............................ 3-14
Starting a warm engine .......................... 5-4
Starting the engine ................................. 5-1
Steering inspection .............................. 6-24
Steering lock (for XJ600N) ..................... 3-3
Storage ................................................... 7-4
Storage compartment .......................... 3-15
T
Tachometer ............................................ 3-7
Throttle cable and grip lubrication ........ 6-22
Throttle cable free play inspection ....... 6-12
Tips for reducing fuel consumption ........ 5-5
Tires ..................................................... 6-13
Tool kit ................................................... 6-1
Troubleshooting ................................... 6-34
Troubleshooting chart .......................... 6-35
Turn indicator lights ............................... 3-3
Turn signal switch .................................. 3-8
V
Valve clearance adjustment ................. 6-13
Vehicle identification number ................. 9-2
W
Wheel bearings .................................... 6-25
Wheels ................................................. 6-15