oil YAMAHA XT660Z 2010 Owner's Manual

1
2
3
4
5
6
7
8
9
10
MOTORCYCLE CARE AND STORAGE
8-4
Long-term
Before storing your motorcycle for sev-
eral months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes
are grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! Toprevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
4. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the side-
stand/centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alter-
natively, turn the wheels a little
every month in order to prevent
the tires from becoming degraded
in one spot.
6. Cover the muffler outlets with
plastic bags to prevent moisture
from entering them.7. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see
page 7-31.
TIP
Make any necessary repairs before
storing the motorcycle.
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 5

SPECIFICATIONS
9-1
1
2
3
4
5
6
7
8
9
10
Engine oil:Type:
SAE10W30 or SAE10W40 or SAE15W40
or SAE20W40 or SAE20W50
Recommended engine oil grade:
API service SE, SF, SG type or higher
Engine oil quantity:
Without oil filter element replacement:
2.50 L (2.64 US qt) (2.19 Imp.qt)
With oil filter element replacement:
2.60 L (2.73 US qt) (2.26 Imp.qt)
Total amount (dry engine):
2.90 L (3.07 US qt) (2.55 Imp.qt)
Cooling system:Radiator capacity (including all routes):
1.2 L (1.26 US qt) (1.05 Imp.qt) (Radiator) +
0.5 L (0.52 US qt) (0.44 Imp.qt)
(Coolant reservoir)
Coolant reservoir capacity (up to the
maximum level mark):
0.50 L (0.52 US qt) (0.44 Imp.qt)
From low to full level:
0.30 L (0.32 US qt) (0.26 Imp.qt)
Air filter:Air filter element:
Paper
Fuel:Recommended fuel:
Premium unleaded gasoline only
Fuel tank capacity:
23.0 L (6.07 US gal) (5.06 Imp.gal)
Fuel reserve amount:
6.7 L (1.76 US gal) (1.46 Imp.gal)
Fuel injection:Manufacturer:
DENSO
Model:
297500-0390
Spark plug:Manufacturer/model:NGK/CR7EGap:
0.7-0.8 mm (0.028-0.032 in)
Clutch:Clutch type:
Wet, multiple-disc
Transmission:Primary reduction system:
Spur gear
Primary reduction ratio:
75/36 (2.083)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
45/15 (3.00)
Transmission type:
Constant mesh 5-speed
Dimensions:Overall length:
2246 mm (88.42 in)
Overall width:
864 mm (34.01 in)
Overall height:
1477 mm (58.14 in)
Seat height:
896 mm (35.27 in)
Wheelbase:
1500 mm (59.05 in)
Ground clearance:
260 mm (10.23 in)
Minimum turning radius:
1958 mm (77.08 in)
Basic weight:With oil and fuel:
208.5 kg (459 lb)
Engine:Engine type:
Liquid cooled 4-stroke, SOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
660.0 cm
3(40.27 cu.in)
Bore x stroke:
100.0 x 84.0 mm (3.94 x 3.31 in)
Compression ratio:
10.00 : 1
Starting system:
Electric starter
Lubrication system:
Dry sump
-20-10 0 1020304050°C
SAE 10W-30
SAE 10W-40
SAE 20W-40
SAE 20W-50
SAE 15W-40
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 6

1
2
3
4
5
6
7
8
9
10
SPECIFICATIONS
9-2
Operation:
Left foot operation
Gear ratio:
1
st:
30/12 (2.500)
2
nd:
26/16 (1.625)
3
rd:
23/20 (1.150)
4
th:
20/22 (0.909)
5
th:
20/26 (0.769)
Chassis:
Frame type:
Diamond
Caster angle:
28°
Trail:
113.0 mm (4.44 in)
Front tire:
Type:
With tube
Size:
90/90-21M/C 54S,
90/90-21M/C 54T
Manufacturer/model:
METZELER/TOURANCE FRONT
MICHELIN/SIRAC
Rear tire:
Type:
With tube
Size:
130/80-17M/C 65S,
130/80-17M/C 65TManufacturer/model:
METZELER/TOURANCE
MICHELIN/SIRAC A
Load:
Maximum load:
190 kg (419 lb)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure
(measured on cold tires):
Load:
Up to 90 kg (0-198 lb)
Front:
210 kPa (30 psi) (2.1 kgf/cm
2)
Rear:
230 kPa (33 psi) (2.3 kgf/cm
2)
Load:
90-190 kg (198-419 lb)
Front:
230 kPa (33 psi) (2.3 kgf/cm
2)
Rear:
250 kPa (36 psi) (2.5 kgf/cm
2)
Off-road riding:
Front:
200 kPa (29 psi) (2.0 kgf/cm
2)
Rear:
200 kPa (29 psi) (2.0 kgf/cm
2)
High-speed riding:
Front:
210 kPa (30 psi) (2.1 kgf/cm
2)
Rear:
230 kPa (33 psi) (2.3 kgf/cm
2)
Front wheel:
Type:
Spoke wheel
Rim size:
21 x 1.85
Rear wheel:
Type:
Spoke wheel
Rim size:
17M/C x MT2.75
Front brake:
Type:
Dual disc brake
Operation:
Right hand
Fluid:
DOT 4
Rear brake:
Type:
Single disc brake
Operation:
Right foot
Fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring/damper type:
Coil spring/oil damper
Wheel travel:
210 mm (8.26 in)
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 7

SPECIFICATIONS
9-3
1
2
3
4
5
6
7
8
9
10
Rear suspension:
Type:
Swingarm (link suspension)
Spring/damper type:
Coil spring/gas-oil damper, spring
preload adjustable
Wheel travel:
200 mm (7.87 in)
Electrical system:
Ignition system:
Transistorized coil ignition (digital)
Charging system:
A.C. magneto
Battery:
Model:
GT9B-4
Voltage, capacity:
12 V, 8 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage x quantity:Headlight:
12 V, 55 W x 2
Auxiliary light:
12 V, 5 W x 2
Tail/brake light:
LED
Front turn signal light:
12 V, 10 W x 2
Rear turn signal light:
12 V, 10 W x 2
Meter lighting:
LED (backlight)Neutral indicator light:
LED
Turn signal indicator light:
LED
High beam indicator light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Immobilizer system indicator light:
LED
Fuses:Main fuse:
30 A
Headlight fuse:
20 A
Signaling system fuse:
10 A
Ignition fuse:
10 A
Parking lighting fuse:
10 A
Radiator fan fuse:
7.5 A
Fuel injection system fuse:
10 A
Backup fuse (for odometer, clock and
immobilizer):
10 A
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 8

1
2
3
4
5
6
7
8
9
10
INDEX
A
Aftermarket Parts, Accessories, and
Modifications ...................................2-4
Aftermarket Tires and Rims ...............2-4
Air filter element, cleaning the check
hose ..............................................7-14
Air filter element, replacing ..............7-14
Auxiliary light bulb, replacing............7-35
Avoid Carbon Monoxide poisoning ....2-2
B
Battery ..............................................7-30
To access the battery ...................7-30
To charge the battery....................7-30
To store the battery.......................7-31
Be a Responsible Owner ...................2-1
Brake and clutch levers, checking
and lubricating ..............................7-26
Brake fluid ........................................7-22
Changing ......................................7-23
Checking fluid level .......................7-22
Brake lever .......................................4-11
Brake pads, checking .......................7-21
Brake pedal ......................................4-11
Checking .......................................7-27
Lubricating ....................................7-27
C
Cables, checking and lubricating .....7-25
Carbon Monoxide (avoid Carbon
Monoxide poisoning).......................2-2
Care and storage ...............................8-1Catalytic converter ...........................4-13
Checking and lubricating the brake
and clutch levers ...........................7-26
Checking and lubricating the brake
pedal .............................................7-27
Checking and lubricating the cables..7-25
Checking and lubricating the
sidestand ......................................7-27
Checking and lubricating the throttle
grip and cable ...............................7-26
Checking the brake pedal ................7-27
Checking the sidestand switch .........4-18
Clock mode ........................................4-7
Clutch lever ......................................4-10
Clutch lever free play, adjusting .......7-20
Consumer information ......................10-1
Controls and instruments ...................3-3
Function ..........................................4-1
Coolant .............................................7-12
Coolant temperature warning light .....4-4
D
Description .........................................3-1
Controls and instrument .................3-3
Left view..........................................3-1
Right view .......................................3-2
Dimmer switch....................................4-9
Drive chain, cleaning
and lubricating ..............................7-25
Drive chain slack ..............................7-23
Adjusting .......................................7-23
Checking .......................................7-23Cleaning and lubricating ...............7-25
E
Emission control system (periodic
maintenance chart) .........................7-2
Engine break-in ..................................6-3
Engine idling speed, adjusting .........7-15
Engine oil and oil filter element ..........7-9
Engine oil filter element....................7-10
Engine stop switch .............................4-9
Engine trouble warning light...............4-4
F
For your safety - Pre-operation
checks .............................................5-1
Front fork ..........................................4-15
Adjusting .......................................4-15
Checking .......................................7-28
Front wheel ......................................7-36
Installing........................................7-37
Removing......................................7-36
Fuel ..................................................4-12
Fuel consumption, tips for reducing ...6-3
Fuel meter ..........................................4-7
Fuel tank breather hose ...................4-13
Fuel tank cap ...................................4-11
Fuses, replacing ...............................7-31
G
Genuine Yamaha Accessories ...........2-3
H
Handlebar switches ............................4-9
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 1

INDEX
1
2
3
4
5
6
7
8
9
10
Dimmer switch ................................4-9
Engine stop switch .........................4-9
Hazard switch ...............................4-10
Horn switch .....................................4-9
Pass switch .....................................4-9
Start switch .....................................4-9
Turn signal switch ...........................4-9
Headlight bulb, replacing..................7-33
High beam indicator light ...................4-4
Horn switch ........................................4-9
I
Identification numbers ......................10-1
Idling speed, checking .....................7-15
Ignition circuit cut-off system............4-17
Checking operation procedure......4-18
Immobilizer system ............................4-1
Immobilizer system indicator light ......4-4
Indicator and warning lights ...............4-3
Coolant temperature warning light..4-4
Engine trouble warning light ...........4-4
High beam indicator light ................4-4
Immobilizer system indicator light...4-4
Neutral indicator light ......................4-4
Turn signal indicator light ................4-3
Instruments ........................................3-3
Instrument and control functions........4-1
K
Key identification number .................10-1
Keys ...................................................4-1L
Labels (location of important labels) ..1-1
License plate light bulb, replacing ....7-35
Location of important labels ...............1-1
Loading ..............................................2-3
Lubricating the brake and clutch
levers ............................................7-26
Lubricating the brake pedal..............7-27
Lubricating the cables ......................7-25
Lubricating the drive chain ...............7-25
Lubricating the sidestand .................7-27
Lubricating the throttle grip
and cable ......................................7-26
Lubricating the swingarm pivots.......7-28
M
Main switch/steering lock ...................4-2
Model label .......................................10-2
Motorcycle noise regulation
(for Australia) ................................10-2
Multi-function display..........................4-5
Clock mode .....................................4-7
Self-diagnosis devices ....................4-7
Tachometer .....................................4-6
Tripmeter and tachometer modes ...4-6
N
Neutral indicator light .........................4-4
O
Oil filter element ..............................7-10
Operation and important riding
points ..............................................6-1Owner’s tool kit...................................7-1
P
Panels, removing and installing .........7-6
Parking ...............................................6-4
Pass switch ........................................4-9
Periodic maintenance
and adjustment ...............................7-1
Periodic maintenance chart for
the emission control system ...........7-2
Pre-operation check list......................5-2
Pre-operation checks .........................5-1
R
Rear suspension, lubricating............7-27
Rear wheel .......................................7-38
Installing........................................7-39
Removing......................................7-38
Record the identification numbers ...10-1
S
Safety information ..............................2-1
Seat ..................................................4-14
Self-diagnosis devices .......................4-7
Shift pedal ........................................4-10
Shifting ...............................................6-2
Shock absorber assembly
(adjusting) .....................................4-16
Sidestand .........................................4-17
Sidestand, checking and lubricating ..7-27
Sidestand switch, checking ..............4-18
Spark plug, checking..........................7-8
XT660Z 08-10 ING-AUS:MY03 07-10 ING 11-05-2009 10:10 Pagina 2