ECU YAMAHA YZ250LC 2001 User Guide

5-2
CHASFRONT WHEEL AND REAR WHEEL
EC598100
REAR WHEEL
Extent of removal:1Rear wheel removal2Wheel bearing removal3Brake disc removal
Extent of removal Order Part name Q’ty Remarks
REAR WHEEL REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
1 Nut (rear wheel axle) 1
2 Rear wheel axle 1
3 Chain puller 2
4 Rear wheel 1 Refer to “REMOVAL POINTS”.
5 Collar 2
6 Driven sprocket 1
7 Oil seal 2
8 Circlip 1
9 Bearing 2 Refer to “REMOVAL POINTS”.
10 Brake disk 1
2
13
3
w
Support the machine securely so there is no dan-
ger of it falling over.
125 Nm (12.5 m•kg, 90 ft•lb)
14 Nm (1.4 m•kg, 10 ft•lb)
42 Nm (4.2 m•kg, 30 ft•lb)
5MW-9-30-5A 7/6/00 8:21 AM Page 4

5-10
CHASFRONT BRAKE AND REAR BRAKE
Extent of removal Order Part name Q’ty Remarks
FRONT BRAKE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Drain the brake fluid. Refer to “REMOVAL POINTS”.
1 Hose cover 1
2 Brake hose holder 1
3 Bolt (brake hose holder) 2 Only loosening.
4 Union bolt 2
5 Brake hose 1
6 Pad pin plug 1
Remove when loosening the pad pin.
7 Pad pin 1Loosen when disassembling the caliper.
8 Caliper 1
9 Brake lever 1
10 Master cylinder bracket 1
11 Master cylinder 1
EC5A0000
FRONT BRAKE AND REAR BRAKEEC5A8000
FRONT BRAKE
Extent of removal:1Brake hose removal2Caliper removal3Master cyilinder removal
w
Support the machine securely so there is no dan-
ger of it falling over.
2
1
3
3
2
9 Nm (0.9 m•kg, 6.5 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
3 Nm (0.3 m•kg, 2.2 ft•lb)
18 Nm (1.8 m•kg, 13 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)30 Nm (3.0 m•kg, 22 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
16 Nm (1.6 m•kg, 11 ft•lb)
23 Nm (2.3 m•kg, 17 ft•lb)
30 Nm (3.0 m•kg, 22 ft•lb)
5MW-9-30-5A 7/6/00 8:27 AM Page 20

5-11
CHASFRONT BRAKE AND REAR BRAKE
EC5A8100
REAR BRAKE
Extent of removal Order Part name Q’ty Remarks
REAR BRAKE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Rear wheel Refer to “FRONT WHEEL AND
REAR WHEEL” section.
Drain the brake fluid. Refer to “REMOVAL POINTS”.
1 Pad pin pulg 1
Remove when loosening the pad pin.
2 Pad pin 1Loosen when disassembling the caliper.
3 Caliper 1
4 Brake hose holder 2
5 Union bolt 2
6 Brake hose 1
7 Brake pedal 1
8 Reservoir tank 1
9 Reservoir hose 1
10 Master cylinder 1
Extent of removal:1Caliper removal2Brake hose removal3Master cylinder removal
w
Support the machine securely so there is no dan-
ger of it falling over.
2
1
3
31
4 Nm (0.4 m•kg, 2.9 ft•lb)7 Nm (0.7 m•kg, 5.1 ft•lb)
30 Nm (3.0 m•kg, 22 ft•lb)
3 Nm (0.3 m•kg, 2.2 ft•lb)
18 Nm (1.8 m•kg, 13 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
26 Nm (2.6 m•kg, 19 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
5MW-9-30-5A 7/6/00 8:28 AM Page 22

5-27
CHASFRONT FORK
Extent of removal Order Part name Q’ty Remarks
FRONT FORK REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Front wheel Refer to “FRONT WHEEL AND
REAR WHEEL”section.
Front caliper Refer to “FRONT BRAKE AND
REAR BRAKE”section.
Number plate
1 Protector 1
2 Brake hose holder 2
3 Pinch bolt (handle crown) 2 Only loosening.
4 Cap bolt 1
Loosen when disassembling the front fork.
5 Pinch bolt (under bracket) 2 Only loosening.
6 Front fork 1
EC550000
FRONT FORK
1
w
Support the machine securely so there is no dan-
ger of it falling over.
Extent of removal:1Front fork removal
4 Nm (0.4 m•kg, 2.9 ft•lb)
20 Nm (2.0 m•kg, 14 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
23 Nm (2.3 m•kg, 17 ft•lb)
5MW-9-30-5B 7/6/00 9:50 AM Page 2

5-47
CHASSTEERING
Extent of removal Order Part name Q’ty Remarks
STEERING REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Number plate
Handlebar Refer to “HANDLEBAR” section.
Cable guide
Front fender
1 Steering shaft nut 1
2 Front fork 2 Refer to “FRONT FORK” section.
3 Handle crown 1
4 Ring nut 1 Use special tool.
Refer to “REMOVAL POINTS”.
5 Under bracket 1
6 Ball race cover 1
7 Bearing (upper) 1
8 Bearing (lower) 1 Refer to “REMOVAL POINTS”.
9 Ball race 2 Refer to “REMOVAL POINTS”.
EC560000
STEERING
Extent of removal:1Under bracket removal 2Bearing removal
2
1
w
Support the machine securely so there is no dan-
ger of it falling over.
23 Nm (2.3 m•kg, 17 ft•lb)
145 Nm (14.5 m•kg, 105 ft•lb)
9Tighten ring nut.
38 Nm (3.8 m•kg, 27 ft•lb)
9Loosen it one turn.
9Retighten it.
7 Nm (0.7 m•kg, 5.1 ft•lb)
TIGHTENING STEPS:
20 Nm (2.0 m•kg, 14 ft•lb)
5MW-9-30-5C 7/6/00 10:45 AM Page 16

5-52
CHASSWINGARM
Extent of removal Order Part name Q’ty Remarks
SWINGARM REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Brake hose holderRefer to “FRONT BRAKE AND
Rear caliperREAR BRAKE”section.
Bolt (brake pedal) Shift the brake pedal backward.
Drive chain
1 Chain support 1
2 Chain tensioner (lower) 1
3
Bolt (rear shock absorber-relay arm)1 Hold the swingarm.
4 Bolt (connecting rod) 1
5 Pivot shaft 1
6 Swingarm 1
EC570000
SWINGARM
Extent of removal:1Swingarm removal
1
w
Support the machine securely so there is no dan-
ger of it falling over.
ü
ý
þ
53 Nm (5.3 m•kg, 38 ft•lb)
80 Nm (8.0 m•kg, 58 ft•lb)
19 Nm (1.9 m•kg, 13 ft•lb)
7 Nm (0.7 m•kg, 51 ft•lb)
85 Nm (8.5 m•kg, 61 ft•lb)
5MW-9-30-5D 7/6/00 11:24 AM Page 2

5-59
CHASREAR SHOCK ABSORBER
EC580000
REAR SHOCK ABSORBER
Extent of removal Order Part name Q’ty Remarks
REAR SHOCK ABSORBER
REMOVAL
Preparation forHold the machine by placing the
removalsuitable stand under the engine.
SeatRefer to “SEAT, FUEL TANK AND
SIDE COVERS” section.
SilencerRefer to “EXHAUST PIPE AND
SILENCER” section.
1 Clamp (air cleaner joint) 1 Loosen the screw (air cleaner joint).
2 Rear frame 1
3
Bolt (rear shock absorber-relay arm)1 Hold the swingarm.
4 Bolt (rear shock absorber-frame) 1
5 Rear shock absorber 1
6 Locknut 1
7 Adjuster 1
8 Spring guide (lower) 1
9 Spring guide (upper) 1
10 Spring (rear shock absorber) 1
11 Bearing 2 Refer to “REMOVAL POINTS”.
2
w
Support the machine securely so there is no dan-
ger of it falling over.
Extent of removal:1Rear shock absorber removal 2Rear shock absorber disassembly
1
56 Nm (5.6 m•kg, 40 ft•lb)
53 Nm (5.3 m•kg, 38 ft•lb)
29 Nm (2.9 m•kg, 21 ft•lb)
5MW-9-30-5D 7/6/00 11:30 AM Page 16