maintenance YAMAHA YZF-R1SC 2004 Service Manual

NOTE:
WARNING
CAUTION:
EAS00030
NOTICE
This manual was produced by the Yamaha Motor Company, Ltd. primarily for use by Yamaha dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one manu-
al. Therefore, anyone who uses this book to perform maintenance and repairs on Yamaha vehicles
should have a basic understanding of mechanics and the techniques to repair these types of vehicles.
Repair and maintenance work attempted by anyone without this knowledge is likely to render the ve-
hicle unsafe and unfit for use.
This model has been designed and manufactured to perform within certain specifications in regard to
performance and emissions. Proper service with the correct tools is necessary to ensure that the ve-
hicle will operate as designed. If there is any question about a service procedure, it is imperative that
you contact a Yamaha dealer for any service information changes that apply to this model. This policy
is intended to provide the customer with the most satisfaction from his vehicle and to conform to federal
environmental quality objectives.
Yamaha Motor Company, Ltd. is continually striving to improve all of its models. Modifications and sig-
nificant changes in specifications or procedures will be forwarded to all authorized Yamaha dealers
and will appear in future editions of this manual where applicable.

This Service Manual contains information regarding periodic maintenance to the emission control
system. Please read this material carefully.

Designs and specifications are subject to change without notice.
EAS00040
IMPORTANT MANUAL INFORMATION
Particularly important information is distinguished in this manual by the following.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
Failure to follow WARNING instructions could result in severe injury or death
to
the motorcycle operator, a bystander or a person checking or repairing the mo-
torcycle.
A CAUTION indicates special precautions that must be taken to avoid damage
to the motorcycle.
NOTE:A NOTE provides key information to make procedures easier or clearer.
ProCarManuals.com

LUBRICATION DIAGRAMS2-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CABLE ROUTING2-35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 3
PERIODIC CHECKS AND ADJUSTMENTS
INTRODUCTION3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PERIODIC MAINTENANCE CHART FOR THE EMISSION
CONTROL SYSTEM3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL MAINTENANCE AND LUBRICATION CHART3-1 . . . . . . . . .
SEATS3-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL TANK3-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE FUEL TANK 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE FUEL PUMP 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE FUEL PUMP 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE FUEL TANK 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COWLINGS3-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT COWLING AND SIDE COWLINGS 3-7. . . . . . . . . . . . . . . . . . .
REAR COWLING 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR FILTER CASE3-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE3-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE VALVE CLEARANCE 3-11. . . . . . . . . . . . . . . . . . . . . .
SYNCHRONIZING THE THROTTLE BODIES 3-17. . . . . . . . . . . . . . . . .
ADJUSTING THE EXHAUST GAS VOLUME 3-19. . . . . . . . . . . . . . . . . .
ADJUSTING THE ENGINE IDLING SPEED 3-21. . . . . . . . . . . . . . . . . . .
ADJUSTING THE THROTTLE CABLE FREE PLAY 3-22. . . . . . . . . . . .
CHECKING THE SPARK PLUGS 3-23. . . . . . . . . . . . . . . . . . . . . . . . . . . .
MEASURING THE COMPRESSION PRESSURE 3-24. . . . . . . . . . . . . .
CHECKING THE ENGINE OIL LEVEL 3-26. . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE ENGINE OIL 3-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MEASURING THE ENGINE OIL PRESSURE 3-29. . . . . . . . . . . . . . . . .
ADJUSTING THE CLUTCH CABLE FREE PLAY 3-31. . . . . . . . . . . . . . .
REPLACING THE AIR FILTER ELEMENT 3-32. . . . . . . . . . . . . . . . . . . .
CHECKING THE FUEL AND BREATHER HOSES 3-33. . . . . . . . . . . . .
CHECKING THE CRANKCASE BREATHER HOSE 3-34. . . . . . . . . . . .
CHECKING THE EXHAUST SYSTEM 3-35. . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE EXUP CABLES 3-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE COOLANT LEVEL 3-37. . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE COOLING SYSTEM 3-38. . . . . . . . . . . . . . . . . . . . . . . .
CHANGING THE COOLANT 3-39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCarManuals.com

3-1
3
INTRODUCTION / PERIODIC MAINTENANCE CHART FOR THE EMISSION
CONTROL SYSTEM / GENERAL MAINTENANCE AND LUBRICATION CHARTCHK
ADJ
EAS00036
PERIODIC CHECKS AND ADJUSTMENTS
INTRODUCTION
This chapter includes all information necessary to perform recommended checks and adjustments. If
followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a
longer service life and reduce the need for costly overhaul work. This information applies to vehicles
already in service as well as to new vehicles that are being prepared for sale, All service technicians
should be familiar with this entire chapter.
PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL SYSTEM
INITIALODOMETER READINGS
No.ITEMROUTINE600 mi
(1000 km)
or
1 month4000 mi
(7000 km)
or
6 months8000 mi
(13000 km)
or
12 months12000 mi
(19000 km)
or
18 months16000 mi
(25000 km)
or
24 months20000 mi
(31000 km)
or
30 months
1*Fuel line
(See page 3-33)
Check fuel hoses for cracks or damage.

Replace if necessary.





2*Spark plugs
(See page 3-23)
Check Condition.

Adjust gap and clean.

Replace every 8000 mi (13000 km) or 12
months.
Replace.
Replace.

3*Valve clearance
(See page 3-11)
Check and adjust valve clearance when en-
gine is cold.Every 26600 mi (42000 km)
4*Crankcase breather
system
(See page 3-34)
Check breather hose for cracks or damage.

Replace if necessary.





5*Electronic fuel injection
(See page 3-17, 21)
Check and adjust engine idle speed and syn-
chronization.






6*Exhaust system
(See page 3-35)
Check for leakage.

Tighten if necessary.

Replace gasket(s) if necessary.





7*Evaporative emission
control system
(For California only)
Check control system for damage.

Replace if necessary.


8*Air induction system
(See page 7-46)
Check the air cut-off valve, reed valve, and
hose for damage.

Replace any damaged parts if necessary.


GENERAL MAINTENANCE AND LUBRICATION CHART
INITIALODOMETER READINGS
No.ITEMROUTINE600 mi
(1000 km)
or
1 month4000 mi
(7000 km)
or
6 months8000 mi
(13000 km)
or
12 months12000 mi
(19000 km)
or
18 months16000 mi
(25000 km)
or
24 months20000 mi
(31000 km)
or
30 months
1*Air filter element
(See page 3-32)
Check condition and damage.
Replace if necessary.





2*Clutch
(See page 3-31)
Check operation.
Adjust or replace cable.






3*Front brake
(See page 3-42, 44, 45)
Check operation, fluid level, and for fluid leak-
age.

Replace brake pads if necessary.






4*Rear brake
(See page 3-43, 44, 45)
Check operation, fluid level, and for fluid leak-
age.

Replace brake pads if necessary.






5*Brake hoses
Check for cracks or damage.




5*Brake hoses(See page 3-46)
Replace.Every 4 years
6*Wheels
(See page 4-3)
Check runout and for damage.
Replace if necessary.





7*Tires
(See page 3-58)
Check tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.






8*Wheel bearings
(See page 4-3)
Check bearings for smooth operation.
Replace if necessary.





ProCarManuals.com

3-2
NOTE:
GENERAL MAINTENANCE AND LUBRICATION CHART
CHK
ADJ
NOTE:
INITIALODOMETER READINGS
No.ITEMROUTINE600 mi
(1000 km)
or
1 month4000 mi
(7000 km)
or
6 months8000 mi
(13000 km)
or
12 months12000 mi
(19000 km)
or
18 months16000 mi
(25000 km)
or
24 months20000 mi
(31000 km)
or
30 months
9*Swingarm pivot
bearings
(See page 4-71)
Check bearing assemblies for looseness.
Moderately repack with lithium-soap-based
grease.
Repack.
10Drive chain
(See page 3-49, 50)
Check chain slack/alignment and condition.
Adjust and lubricate chain with a special O-
ring chain lubricant thoroughly.Every 600 mi (800 km) and after washing the motorcycle or riding in the rain
11*Steering bearings
(See page 3-51)
Check bearing assembly for looseness.
Moderately repack with lithium-soap-based
grease every 16000 mi (25000 km) or 24
months.



Repack.

12*Steering damper
(See page 4-60)
Check operation and for oil leakage.





13*Chassis fasteners
(See page 2-23)
Check all chassis fitting and fasteners.
Correct if necessary.





14Brake and clutch
lever pivot shafts
(See page 3-61)
Apply lithium-soap-based grease (all-purpose
grease) lightly.





15Sidestand pivot(See page 3-61)

Check operation.

Apply lithium-soap-based grease (all-pur-
pose grease) lightly.





16*Sidestand switch
(See page 3-61, 8-4)
Check operation and replace if necessary.






17*Front fork
(See page 3-53)
Check operation and for oil leakage.
Replace if necessary.





18*Shock absorber
assembly
(See page 3-56, 4-67)
Check operation and for oil leakage.
Replace if necessary.





19*Rear suspension
link pivots
(See page 4-71)
Check operation.
Correct if necessary.


20Engine oil
(See page 3-26, 28)
Change (warm engine before draining.)






21*Engine oil filter cartridge
(See page 3-28)
Replace.



22*Cooling system

Check hoses for cracks or damage.
Replace if necessary.





22*Cooling system(See page 3-37, 38, 39)
Change with ethylene glycol antifreeze cool-
ant every 24 months.Change.
23*EXUP system
(See page 3-36)
Check operation, cable free play and pulley
position.
Every 12000 mi (19000 km)
24*Control cables
(See page 3-61)
Apply Yamaha chain and cable lube or en-
gine oil SAE 10W-30 thoroughly.






25*Throttle grip housing
and cable
(See page 3-22)
Check operation and free play.
Adjust the throttle cable free play if necessary.
Lubricate the throttle grip housing and cable.





* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi
(13000 km) or 12 months.
Air filter

This model’s air filter is equipped with a disposable oil-coated paper element, which must not be
cleaned with compressed air to avoid damaging it.

The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
Hydraulic brake service

After disassembling the brake master cylinders and calipers, always change the fluid. Regularly
check the brake fluid levels and fill the reservoirs as required.

Every two years replace the internal components of the brake master cylinders and calipers, and
change the brake fluid.

Replace the brake hoses every four years and if cracked or damaged.
ProCarManuals.com

7-15
FUEL INJECTION SYSTEMFI
Cylinder identification sensor
output voltage
When sensor is on
4.8 V or more
When sensor is off
0.8 V or less Tester positive probe
white / black
Tester negative probe
black / blue
1
2
TROUBLESHOOTING DETAILS
This section describes the measures per fault code number displayed on the meter. Carry out check
and maintenance on items or components that could be a cause of malfunction in accordance with the
order.
When the check and maintenance of malfunctioned part is completed, restore the meter display ac-
cording to the “Restore method”.
Fault code No.:
Fault code number displayed on the meter when the engine failed to work normally. (Refer to “Diag-
nostic fault code table”.)
Diagnostic code No.:
Code number to be used when the diagnostic monitoring mode is operated. (Refer to “DIAGNOS-
TIC MODE”.)
Fault code No.11SymptomNo normal signals are received from the cylinder identification sensor.
Used diagnostic code No. – –
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Installed condition of sensorCheck the installed area for looseness or
pinching.Reinstated by
starting the
2Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
Cylinder identification sensor coupler
Main wiring harness ECU coupler
Sub-wire harness couplerengine and
operating it at
idle.
3Open or short circuit in wiring harness
and / or sub lead.Repair or replace if there is an open or short circuit.
Between sensor coupler and ECU coupler
Blue – Blue
White / Black – White / Black
Black / Blue – Black / Blue
4Defective cylinder identification sensor.Replace if defective.
1. Connect the pocket tester (DC 20 V) to the
cylinder identification sensor coupler terminal
as shown.
2. Set the main switch to “ON”.
3. Measure the cylinder identification sensor out-
put voltage.
4. Is the cylinder identification sensor OK?
ProCarManuals.com