jack points AUDI S6 2015 Owners Manual

M N
0 I.J "". rl I.O
"' rl
"' rl
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury.
@ Tips
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts.
- If a wheel bolt is very tight, you may find
it easier to loosen by carefully push ing
down on the end of the wheel bolt
wrench with
one foot only. As you do so,
hold on to the car to keep your ba lance
and take care not to slip.
Raising the vehicle
The vehicle must be lifted with the jock first
before the wheel con be removed .
Fig. 209 Sill pane ls: markings
'ii
9
--~~ :;:~:'.'"'-i
Fi g. 210 Sill: posit ion ing th e ve hicle jack
~ Activate the vehicle jack mode* in the M MI:
I CAR I funct ion button> ( C ar)* s ystem s con­
t rol button >
Servicing & c heck s > Air susp.:
jack mode
> On .
~ Engage the parking bra ke to prevent your
vehicle from rol ling un intentionally.
~ Move the selector le ver to position P.
What do I d o now ? 275
~ Fi nd the marking (imprint) on the sill that is
nearest the whee l that will be changed
r::!) fig. 209. Beh ind the marking, there is a
lift ing point on the sill for the veh icle jack.
~ Vehicles w ith a sill: remove the cover from
the sill before lift ing the veh icle with a vehi­
cle jack
r::!) page 2 76.
~ Tu rn the v ehicle ja ck located under the lift­
ing point on the sill to ra ise the jack unt il its
a rm @<::!)
fig. 210 is lo cated under the des­
ig nated p lastic moun t
r::!) .&, r::!)(D,
~ Align the jack so that its arm@ r::::> fig. 210
engages in the designated lifting point i n
the door s ill and the movable base ® lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point @.
~ Wind the jack up further until the flat t ire
comes off the ground
r::!) & .
Position the vehicle jack only under the desig­
nated lifting points on the sill
Q fig . 209 .
There is exactly one locat ion for each wheel.
The jack must not be positioned at any other lo c a ti o n
r::!) A r::!) An un stable surface under the jack can cause
the vehicle to slip off the jack . Always provide
a fi rm base for the jack on the g ro und . If nec­
essary p lace a sturdy board or sim ila r support
u nder the jack. On
hard , slippery surfaces
(such as tiles) use a rubbe r mat or similar to
prevent the jack from slipping
r::!) & .
&_ WARNING
-You or your passengers co uld be in ju red
while changing a whee l if you do not fo l­
low t hese safety preca utions:
- Position the vehicle jack on ly at the
d esigna ted lifti ng points and align the
j a ck . O therw ise, the vehicle ja ck could
s lip and cause an injury i f it does not
have sufficient hold on the vehicle.
- A soft or uns table surface unde r the
j ack may cause the ve hicle to slip off
the jack. A lways provide a firm base for
the jack on the ground . If necessary,
use a st urdy boa rd under the jack.
~

276 What do I do now?
-On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you a re
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­ matically at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles: with sill
Fig . 211 Sill: remov ing t he cover
.. Pull the cover down to remove it¢ fig . 211.
.,. To install the cover again , insert it into the
retainers and then swing it upward until it
clicks into place. The cover must be flush
with the sill.
(D Tips
Some models may also have a cover for the
rear vehicle lift point.
Taking the wheel off /installing the spare
Follow these instructions st ep-by-step for
changing the wheel.
Fig. 212 Changing a wheel: using the screwdrive r han­
dle (w it h th e blade re m oved) to turn the bolt s
Fig. 213 Changing a wheel: alignment p in ins ide t he
top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwdriv­
er handle
to completely remove the top­
most wheel bolt and set it aside on a
clean
surface ¢ fig. 212 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig . 213 .
.,. Then remove the other wheel bolts as de­
scribed above .
.. Take off the wheel leaving the alignment pin
in the bolt hole
¢(D . Ill>

M N
0 I.J "". rl I.O
"'
@ Tips
Check carefully to make sure the hook-up
is secure before moving the car up the flat­
bed truck ramp .
Vehicle transport
Whenever you hov e your vehicle transported,
be sure to note the following :
(D Note
Mount the tie-down chains/cables over the
running surface (circumference) of the
tires. Never secure the vehicle by the axle,
the suspension struts or the front or rear
towline eye . For technical reasons, the
pressure in the suspension struts may
change du ring the transport and this will
adve rsely affect vehicle handling.
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may onl y be li~ed at the lif ting
points illu stra ted.
Fi g. 2 25 Front l ift ing po int
Fig. 226 Rea r lifti ng poin t
:;:; N 0 6 ., a,
5 .. Read and heed WARNING Q ,&..
Emergenc y situ ation s 287
.. Activate the vehicle jack mode* in the MM I:
!CAR I function button > (C ar)* s ystem s con­
trol button>
S e rv ic ing & check s> Air su sp. :
jack m ode> On .
.. Locate lifting poin ts Q fig . 225 and
Q fig . 226 .
.. Adjust lifting arms of workshop hoist or
floor jack to match veh icle lifting points.
.. Insert a rubber pad be tween the floor jack/
workshop hoist and the lift ing po in ts.
The vehicle jack mode* must be activated so
that the automat ic adjustment of the Adap­
tive Ai r Suspens ion* does not make it more
diffi cult to raise the vehicle with the floor
jack.
If yo u must lift your v ehi cle with a floor jack
t o wo rk und ern eath , be sure th e vehicle i s
s af ely s upported on s tands intended for thi s
purpo se.
Front lifting point
The lifting po int is located on the floor pan re­
inforcement abo ut at the same leve l as the
jac k mounting point
Q fig. 225 . Do n ot lift
t h e ve hicle at th e verti cal sill reinforc em ent .
Re ar lifting point
The lifting point is located on the vert ical rein­
forcement of the lower sill for the on-boa rd
ja ck
c::> fig. 226 .
Lifting with veh icle j ack
Re fer to Q page 275.
A WARNING
-To reduce the risk of ser ious injury and
veh icle damage .
- Always lift the veh icle only at the spe ­
cia l workshop hoist and floor jack lift
po ints illust rated
c::> fig . 225 and
c::> fig . 226.
- Failu re to lift the vehicle at these
po ints could cause the vehicle to tilt or
fall from a lift if there is a change in ve­
hicle weight distribution and balance .
This might happen, for example, when
-

288 Emergency situations
heavy components such as the engine
b lock or transmiss io n are removed.
- W he n removing heavy components like
these, ancho r vehicle to ho ist o r add cor­
responding weig hts to ma inta in the cen ­
ter of g ravity . Othe rwise, the vehicle
might tilt or s lip off t he hoist, causing
ser ious p erson al injury.
(D Note
-Be awa re of the follow ing points befo re
li fting the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the
front or rear axle or the body side
membe rs. This could lead to ser ious
damage.
- To avoid damage to the underbody or
chassis frame , a rubber pad must be
i nserted between the floor jack and
the l ift points.
- Before driving over a workshop hoist,
check that the veh icle weight does not
exceed the permissible lifting capacity
of the hoist .
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.