fuel pressure MITSUBISHI 3000GT 1991 Workshop Manual

13-146FUEL SYSTEM - Fuel Tank
FUEL TANKREMOVAL AND INSTALLATIONM13GA- -12 Nm
8 ft.lbs. WPre-removal Operation
l Draining of the Fuel0 Release of Residual Pressure fromHigh Pressure Hose.(Referto P.13-137.)
5-6Nm25 ft.lbs.
b22 ftlbs.16
V26 Nm
19 ft.lbs.
03FOOO7
Removal steps
** I. Fuel gauge cover2. Fuel pump and fuel gauge unit assembly
connector
3. Fuel tank cap4. Drain plug
5. Splash shield
6. Fuel filler neck protector
** 7. Vapor hose8. Fuel filler neck9. Fuel filler hose
l * IO. Vapor hosel 11. Return hose+* l * 12. High pressure fuel hosel * 13. Vapor hose14. Leveling pipe15. Self-locking nut
16. Fuel tank++
17. Overfill limiter (Two-way valve)I)+ 18. Vapor hosel + 19. Fuel pump and fuel gauge unit assembly
;d
I
1 TSB Revision

FUEL SYSTEM - Fuel Tank13-147
Rubber hose
ngn
03FOOl
9
OSFOOB
05FOO7SERVICE POINT OF REMOVAL
MlBGBAK
12. DISCONNECTION OF HIGH PRESSURE FUEL HOSEDisconnect the hose from body main pipe first and then
from fuel pump.
Caution
Cover the hose connection with rags to prevent splash
of fuel that could be caused by some residual pressurein the fuel pipe line.
INSPECTION
MlBGCAMl Check the hoses and the pipes for crack or damage.
l Check the fuel tank cap for malfunction.
l Check the fuel tank for deformation, corrosion or crack.
l Check the fuel tank for dust or foreign material.
NOTEIf the inside of the fuel tank is to be cleaned, use any one of
the following:
(1) Kerosene
(2) Trichloroethylene
(3) A neutral emulsion type detergent
OVERFILL LIMITER (TWO-WAY VALVE)Connect a clean rubber hose to the overfill limiter and check for
operation.
Inspection procedureLightly blow from the inlet
(fuel tank) sideNormal conditionAir passes through after a
slight resistanceLightly blow from the outletAir passes through
(canister) sideISERVICE POINTS OF INSTALLATION
MlSGDAT19. INSTALLATION OF FUEL PUMP AND FUEL GAUGE
UNIT ASSEMBLY
Align the three positioning projections of the packing with
the holes in the fuel pump and fuel gauge unit assembly.
TSB Revision18.13. IO. 7. CONNECTION OF VAPOR HOSE
(1) If the pipe has a stepped part, connect the vapor hose
to the pipe securely, up to the stepped part, as shown in
the illustration.
(2) If the pipe does not have a stepped part, connect the
vapor hose to the pipe securely, so that it is the
standard value.
Standard value: 25
- 30 mm (1.0 - I.2 in.)

13-148FUEL SYSTEM - Fuel Tank
Canistide
Do3041Flare nut
Se&e side
0310430%
e:00817. INSTALLATION OF OVERFILL LIMITER (TWO-WAY
VALVE)Install so that the overfill limiter is facing in the direction
’,~
shown in the illustration.L.&l
12. CONNECTION OF HIGH PRESSURE FUEL HOSETemporarily tighten the flare nut by hand, and then tighten it
to the specified torque, being careful that the high pressure
fuel hose does not become twisted.
CautionWhen tightening flare nut, be careful not to bend or
twist line to prevent fuel pump from damage.
11. CONNECTION OF RETURN HOSEConnect the return hose to the pipe securely, up to the
stepped part, as shown in the illustration.
1. INSTALLATION OF FUEL GAUGE COVER
Before installing the fuel gauge cover, apply the specified
sealant to the rear floor pan.
Specified sealant: 3M ATD Part No. 8509 or equivalent
TSB Revision

FUEL SYSTEMFuel Pump and Fuel Gauge Unit Assembly- and Overfill Limiter (Two-Wav Valve)13449
FUEL PUMP AND FUEL GAUGE UNIT ASSEMBLY ANDOVERFILL
LIMITER (TWO-WAY VALVE)
1:REMOVAL AND INSTALLATIONMIBUA- -
L
Removal steps
l *1. Fuel gauge cover
2. Fuel pump and fuel gauge unit assembly
connectorl *3. Overfill limiter (Two-way valve)*I) I)+4. High pressure fuel hose connection (body
side)a* I)*5. High pressure fuel hose connection.
(tuel pump side)03FOOO7l *6. Fuel pump and fuel gauge unit assembly
~03FOOll
I
LJISERVICE POINTS OF REMOVAL
MlSUBAC4. DISCONNECTION OF HIGH PRESSURE FUEL HOSE
(BODY SIDE)
Caution
Cover the hose connection with rags to prevent’splash
of fuel that could be caused by some residual pressurein the fuel pipe line.
5. DISCONNECTION OF HIGH PRESSURE FUEL HOSE
(FUEL PUMP SIDE)
NOTEHold the pump side nut with a wrench while turning the nut
on the hose side.
[TSB RevisionI

13-150FUEL SYSTEMFuel Pump and Fuel Gauge Unit Assembly- and Overfill Limiter (Two-Way Valve)
Rubber hose
9Flare nut
Secure side
03Yo43Camst
ide
DO304INSPECTION
MlBUCAB
OVERFILL LIMITER (TWO-WAY VALVE)~
Connect a clean rubber hose to the overfill limiter and check for
operation.
‘d
Inspection procedureNormal conditionLightly blow from the inlet
(fuel tank) sideAir passes through after a
slight resistanceLightly blow from the outlet
(canister) sideAir passes through
SERVICE POINTS OF INSTALLATION
M13UDAC6. INSTALLATION OF FUEL PUMP AND FUEL GAUGE
UNIT ASSEMBLY
Align the three positioning projections of the packing with
the holes in the fuel pump and fuel gauge unit assembly.
5. 4. CONNECTION OF HIGH PRESSURE FUEL HOSE
Temporarily tighten the flare nut by hand, and then tighten it
to the specified torque, being careful that the high pressure
fuel hose does not become twisted.
CautionWhen tightening flare nut, be careful not to bend or
[J’twist line to prevent fuel pump from damage.\3. INSTALLATION OF OVERFILL LIMITER (TWO-WAY
VALVE)Install so that the overfill limiter is facing in the direction
shown in the illustration.
1. INSTALLATION OF FUEL GAUGE COVER
Before installing the fuel gauge cover, apply the specified
sealant to the rear floor pan.
Specified sealant: 3M ATD Part No. 8509 or equivalent
1 TSB RevisionIII

FUEL SYSTEM- Fuel Line and Vapor Line13451FUEL
LINE AND VAPOR LINEMlBKA-~
iREMOVAL AND INSTALLATION
i30 Nm
6

Removal steps
1, Reserve tank2. Battery
3. Battery tray with washer tank assembly
4. Purge control valve
M 5. Fuelvapor hose6. Canister
7. Vapor pipe assembly
l +8. Fuel return hosea*9. Eye bolt10. Gasket11. High pressure fuel pipel a 12. Fuel filter*I,13. Eye bolt
14. Gasket
l * 15. High pressure fuel hose
16. O-ring
w 17. Fuel vapor hose
18. Stone protector
19. Fuel vapor pipe20. Fuel return pipe
21. Fuel main pipe
Deli\rerye
i603N0012
1 TSB Revision

13-152FUEL SYSTEM- Fuel Line and Vapor Line
03FOO3
05FOO735 Nm7r; ft
Ihr-k” ._..I_.
@dFlare nut,xSERVICE POINTS OF REMOVAL
MlBKBAQ9. 13. REMOVAL OF EYE BOLT
Remove the eye bolt while holding the fuel filter nut
\securely.
Caution
Cover the hose connection with rags to prevent splash
of fuel that could be caused by some residual pressurein the fuel pipe line.
INSPECTION
MIBKCAJ
lCheck the hoses and pipes for cracks, bend, deformation
and clogging.
l Check the canister for clogging.
l Check the fuel filter for clogging and damage.
SERVICE POINTS OF INSTALLATION
MlSKDAU17.5. INSTALLATION OF FUEL VAPOR HOSE
/ 8. FUEL
RETURN HOSE
(1) If the fuel pipe has a stepped part, connect the fuel
hose to the pipe securely, up to the stepped part, as
shown in the illustration.
Iti(2) If the fuel pipe does not have a stepped part, connect
the fuel hose to the pipe securely, so that it is the
standard value.
Standard value: 25
- 30 mm (1.0 - 1.2 in.)
15. INSTALLATION OF HIGH PRESSURE FUEL HOSEApply engine oil to the hose union.
Insert the hose, being careful not to damage the O-ring, and
tighten securely.
CautionBecause there is high pressure applied between the
fuel pump and the injection mixer, be especially sure
that there is no fuel leakage in this area.
12. INSTALLATION OF FUEL FILTER(1) When installing the fuel filter, first temporarily install the
filter to the filter bracket; then insert the main pipe at
the connector part of the high pressure fuel pipe, and
manually screw in the main pipe’s flare nut.
(2) Holding the fuel filter nut, tighten the fuel main pipe’s
flare nut and eye bolt at the specified torque. Then
tighten the filter to the bracket.
TSB Revision1
‘d

FUEL SYSTEM - Fuel Filter13453
FUEL FILTERM13VA-.
/REMOVAL AND INSTALLATION
i&J
L
/Il Removal of Residual Pressure from
Post-installation Operation
l Checking for Fuel Leakage
Removal steps
1. Battery
2. Battery tray with washer tank assembly
3. Eye bolt4. Gasket
5. High pressure fuel hose
6. Connection of fuel main
pipe7. Mounting boltl *8. Fuel filterl *9. Eye bolt10. Gasket11. High pressure fuel pipe
l---
222 ft.lbs.03FOO12
Gasket
fuel pipe
&----Eye bo’t 03FOO13SERVICE POINTS OF REMOVAL
MlSVBAB3. 9. REMOVAL OF EYE BOLT
Remove the eye bolt while holding the fuel filter nut
securely.
Caution
Cover the hose connection with
rags to prevent splash
of fuel that could be caused by some residual pressurein the fuel pipe line.
SERVICE POINT OF INSTALLATION
M13VBAB8. INSTALLATION OF FUEL FILTER
(1) When installing the fuel filter, first temporarily install the
filter to the filter bracket; then insert the main pipe at
the connector part of the high pressure fuel pipe, and
manually screw in the main pipe’s flare nut.
(2) Holding the fuel filter nut, tighten the fuel main pipe’s
flare nut and eye bolt at the specified torque. Then
tighten the filter to the bracket.
TSB Revision

15-16INTAKE AND EXHAUST - Intake Manifold
INTAKE MANIFOLD
REMOVAL AND INSTALLATION
Pre-removal Operationl Release of Residual Pressure fromHigh Pressure Fuel Hose(Refer to GROUP 13-ServiceAdjustment Procedures.)l Draining of Engine Coolant (Refer
to GROUP 00 -Maintenance Service,)
l Removal of Air Intake Plenum(Referto P.15-13, 14.)5Nm
lo-13Nm4 ft.lbs.8-9ftJbs. w2\I
Post-installation Operationl Installation of Air Intake Plenum
(Refer to P.1.5-13. 14.)l Filling of Engine Coolant
(Refer to GROUP 00 - Maintenance
Service.)
l Adjustment of Accelerator Cable(Referto GROUP 13-EngineControl.). Checkina for Fuel Leakage6
5
2 :‘;bs.)
gp,.qgs ~-zt!EJ8OSFOO24
Removal steps
I. Connection for high-pressure fuel hose
2. O-ring
3. Connection for fuel return hose
4. Connection for vacuum hoses
5. Connection for injector connector
6. Delivery pipe (with injectors)
7. Insulators
8. Timing belt upper cover
I)*9. Intake manifold mounting nut I)* 10. Intake manifold mounting nut II. Cone disc spring
12. Intake manifold-
** 13. Intake manifold gasket
TSB Revision

EMISSION CONTROL - Vacuum Hoses
VACUUM 1-10sEs
lVACUUM HOSES ROUTING
L//
17-3M17JA-
-
I’
Li
Fuel pressureregulator
Vehicle front
id
L: Light blueR: RedB: Black
7EM0131
EGR controlsolenoid valve
r-c,cud valve/
Canister
/Fuel pressureregulator
v
Vehicle frontG: GreenY: Yellow
L: Light blueR: RedB: Black
TSB Revision
7EM0132I
1