engine Abarth Punto 2014 Owner handbook (in English)

REFUELLING
Only refuel with unleaded petrol with octane rating
(RON) not less than 95 conforming to the European
specification EN 228.
The use of petrol that does not conform to the
above-mentioned specification will cause the EOBD
warning light to come on and the irregular operation
of the engine.
STARTING THE ENGINE
Make sure that the handbrake is engaged; set the
gearshift lever to neutral; fully depress the clutch
without pressing the accelerator, then turn the ignition
key to AVV and release it as soon as the engine has
started.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter develops high temperatures
during operation. Do not park the car on grass, dry
leaves, pine needles or other flammable material: fire
hazard.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that allows continuous
diagnosis of the components linked to emissions to
ensure better respect for the environment.ELECTRICAL ACCESSORIES
If, after buying the car, you decide to add electrical
accessories (with the risk of gradually draining the
battery), contact an Abarth Dealership. They can
calculate the overall electrical requirement and check
that the vehicle electric system can support the
required load.
CODE card (for versions/markets where provided)
Keep the card in a safe place, not in the car.
Make sure you have the electronic code written on
the CODE card with you at all times.
SCHEDULED SERVICING
Correct car servicing is essential for ensuring it stays in
tip-top condition and safeguards its safety features, its
environmental friendliness and low running costs for
a long time to come.
THE OWNER HANDBOOK CONTAINS…
... important information and warnings on the correct
use and maintenance of your car over time as well as
safe driving tips. Pay special attention to the symbols
"(personal safety) #(car safety) !(environmental
protection).
VERY IMPORTANT
K


001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 2

THE FIAT CODE SYSTEM
This is an electronic engine locking system which
increases protection against attempted thefts of the car.
It is automatically activated when the ignition key is
removed.
An electronic device is fitted in each ignition key grip.
The device transmits a radio-frequency signal when the
engine is started through a special aerial built into the
ignition switch. The modulated signal, which changes
each time the engine is started, is the “password”, by
means of which the control unit recognises the key and
enables to start the engine.
OPERATION
Each time the vehicle is started by turning the ignition
key to MAR, the Fiat CODE system control unit sends
a recognition code to the engine control unit to
deactivate the immobiliser.
The acknowledgement code is sent only if the Fiat
CODE system control unit has recognised the code
transmitted from the key.
Each time the ignition key is turned to STOP, the Fiat
CODE system deactivates the functions of the engine
management control unit.
If the code is not recognised correctly during ignition,
the
Ywarning light comes on in the instrument panel.
SYMBOLS
Special coloured labels have been attached near or
actually on some of the components of your car. These
labels bear symbols that remind you of the precautions
to be taken as regards that particular component.
The plate summarising the symbols used can be found
under the bonnet, fig. 2.
F0U003Abfig. 2
CONTENTS TECHNICAL
SPECIFICATIONS
MAINTENANCE
AND CARE
IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGESSTARTING
AND DRIVINGSAFETY
KNOWING
YOUR VEHICLE
4
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 4

THE KEYS
CODE CARD fig. 3
(for versions/markets where provided)
The car is delivered with two copies of the ignition key
and with the CODE card, which bears the following:
A the electronic code;
B The mechanical key code to be given to the Abarth
Dealership when ordering duplicate keys.
You should have the electronic code A-fig. 3 with you at
all times.
IMPORTANT In order to ensure complete efficiency of
the electronic devices inside the keys, they should never
be exposed to direct sunlight. In this case turn the key to STOP and then to MAR; if
the lock persists try again with the spare set of keys.
Contact an Abarth Dealership if you still cannot start
the engine.
Warning light
Ycoming on when driving
❒If the warning light Yturns on, this means that the
system is running a self-diagnosis (for example for a
voltage drop).
❒If the warning light Ystays on, contact an Abarth
Dealership.
The electronic components inside the key
may be damaged if the key is submitted
to sharp knocks.
F0U004Abfig. 3
CONTENTS TECHNICAL
SPECIFICATIONS
MAINTENANCE
AND CARE
IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGES STARTING
AND DRIVING SAFETY
KNOWING
YOUR VEHICLE
5
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 5

11
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
fig. 9F0U010Ab
If the ignition device has been tampered
with (e.g. an attempted theft), have it
checked over by an Abarth Dealership as soon
as possible.
WARNING
When getting out of the car, always
remove the key to prevent someone
from accidentally activating the controls.
Remember to engage the handbrake. If the car
is parked on a slope uphill, engage the first
gear; if the car is facing downhill, engage the
reverse gear. Never leave children unattended
in the car.
WARNING
IGNITION
The key can be turned to 3 different positions fig. 9:
❒STOP: engine off, key can be extracted, steering
locked. Some electrical devices (e.g. sound system,
central door locking system, etc.) may work.
❒MAR: driving position. All electric devices can
operate.
❒AVV: engine starting (temporary position).
The ignition switch is fitted with an electronic safety
system that requires the ignition key to be turned back
to STOP if the engine will not start, before the starting
operation can be repeated.
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 11

INSTRUMENT PANEL
A Speedometer (speed indicator)
B Fuel level gauge with reserve
warning light
C Engine coolant temperature
gauge with overheating warning
light
D Rev counter
E Reconfigurable multifunction
display
F0U011Abfig. 10
CONTENTS TECHNICAL
SPECIFICATIONS
MAINTENANCE
AND CARE
IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGES STARTING
AND DRIVING SAFETY
KNOWING
YOUR VEHICLE
13
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 13

CONTENTS TECHNICAL
SPECIFICATIONS
MAINTENANCE
AND CARE
IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGESSTARTING
AND DRIVINGSAFETY
KNOWING
YOUR VEHICLE
14
INSTRUMENTS
The instrument background colour and type may vary
according to the versions.
SPEEDOMETER fig. 11
This shows the speed of the vehicle.
REV COUNTER fig. 12
The rev counter shows the engine rpm.
IMPORTANT The electronic injection control system
gradually shuts off the flow of fuel when the engine is
“over-revving” resulting in a gradual loss of engine
power.
When the engine is idling, the rev counter may indicate
a gradual or sudden increase of the speed.This behaviour is standard as it takes place during the
activation of the climate control system or the fan.
It should not be considered as a fault. In these cases,
a slow change in revs is used to protect the battery
charge.
FUEL LEVEL GAUGE fig. 13
The needle shows the amount of fuel left in the fuel
tank.
E tank empty
F tank full
The reserve warning light A comes on to indicate that
approximately 7 litres of fuel are left in the tank.
Do not travel with the fuel tank almost empty: the gaps
in fuel delivery could damage the catalytic converter.
fig. 12F0U014Abfig. 11F0U013Ab
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 14

CONTENTS TECHNICAL
SPECIFICATIONS
MAINTENANCE
AND CARE
IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGES STARTING
AND DRIVING SAFETY
KNOWING
YOUR VEHICLE
15
F0U015Abfig. 13F0U016Abfig. 14
C Low engine coolant temperature.
H High engine coolant temperature.
Warning light B may light up (and a message on the
reconfigurable multifunction display may appear in
certain versions) to indicate that the coolant
temperature is too high; in this case, stop the engine and
contact an Abarth Dealership. See the description in the “Refuelling” paragraph.
IMPORTANT The needle will point to E and warning
light A will flash to indicate a fault in the system. If this is
the case, go to an Abarth Dealership to have the system
checked.
ENGINE COOLANT TEMPERATURE
GAUGE fig. 14
This shows the temperature of the engine coolant fluid
and starts working when the fluid temperature exceeds
approx. 50°C.
Under normal conditions, the needle assumes different
positions within the scale depending on the usage
conditions.
If the needle reaches the red area, stop
the engine immediately and contact an
Abarth Dealership.
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 15

CONTENTS TECHNICAL
SPECIFICATIONS
MAINTENANCE
AND CARE
IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGESSTARTING
AND DRIVINGSAFETY
KNOWING
YOUR VEHICLE
16fig. 15F0U2050Abg
RECONFIGURABLE MULTIFUNCTION
DISPLAY
The car may be equipped with a reconfigurable
multifunction display that, according to previous
settings, will show useful driving information.“STANDARD” SCREEN fig. 15
The standard screen shows the following information:
A Time
B Date
D Odometer (display of distance travelled in
kilometres/miles)
E Car status indications (e.g. doors open, possible ice on
road, etc.)
F Headlamp alignment position (only with dipped
headlamps on)
G Outside temperature
When the ignition key is turned to MAR, the display’s
main screen will show the date fig. 15 or the
turbocharging pressure fig. 16, depending on the setting
previously chosen from the “First page” menu item
(“Date” or “Engine info”).
fig. 16F0U196Ab
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 16

CONTENTS TECHNICAL
SPECIFICATIONS
MAINTENANCE
AND CARE
IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGES STARTING
AND DRIVING SAFETY
KNOWING
YOUR VEHICLE
23
FIRST PAGE
(display of information on the main screen)
This function allows you to choose the information you
would like to see on the main screen. You can choose
to display the date or the turbocharger boost pressure.
To make your choice, proceed as follows:
– briefly press MENU ESC: “First page” will appear on
the display;
– briefly press MENU ESC again to show the display
options: “Date” and “Engine info”;
– press +or –to select the information you wish to see
on the main page of the display;
– briefly press the MENU ESC button to go back to the
menu screen or hold the button down to go back to the
standard screen without saving.
When the key is turned to MAR and the initial check
stage is over, the display will show the information
selected via the “First page” menu function. SET DATE
(Setting the date)
Using this function you can update the date
(day – month – year).
Proceed as follows to update:
– briefly press MENU ESC: the day (dd) will flash on the
display;
– press the button +or –for setting;
– briefly press MENU ESC: the month (mm) will flash on
the display;
– press the button +or –for setting;
– briefly press MENU ESC: the year (yyyy) will flash on
the display;
– press the button +or –for setting.
NOTE The setting increases or decreases by one unit
each time button +or – is pressed. Hold the button
pressed to increase/decrease the setting rapidly and
automatically. Complete the setting by briefly pressing
the button when you approach the required value.
– briefly press the MENU ESC button to go back to the
menu screen or hold the button down to go back to the
standard screen without saving.
001-028 PUNTO Abarth GB 1ed 17-07-2012 12:04 Pagina 23

29
Values displayed
Outside temperature
Indicates the temperature outside the vehicle passenger
compartment.
Range
This indicates the approximate distance that may be
travelled with the fuel remaining in the tank, assuming
that driving conditions do not change. The display will
show the reading
“----“ when the following events take place:
– range value lower than 50 km (or 30 mi)
– car parked with engine running for a long period.
Distance travelled
This value shows the distance covered from the start of
the new journey.
Average consumption
This value shows the approximate average fuel
consumption from the start of the new journey.
Current consumption
This indicates the fuel consumption. The value is
constantly updated. The display will show “----” if the
car is parked with the engine running.
Average speed
This value shows the car’s average speed as a function
of the overall time elapsed since the start of the new
mission.TRIP COMPUTER
General information
The Trip computer is used to display information on car
operation when the key is turned to MAR. This function
is made up of two separate trips called “Trip A” and
“Trip B” which can monitor the car’s “complete mission”
independently of each other. Both functions can be
zeroed
(reset - start of a new journey).
“Trip A” is used to display the figures relating to:
– Outside temperature
– Range
– Trip distance
– Average consumption
– Current consumption
– Average speed
– Trip time (driving time).
Trip B allows the display of the following parameters:
– Trip distance B
– Average consumption B
– Average speed B
– Trip time B (driving time).
N.B. “Trip B” may be disabled (see “Activating Trip B”).
“Range” and “Instantaneous consumption” cannot be
reset.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
029-068 PUNTO Abarth GB 1ed 17-07-2012 12:05 Pagina 29