lock Abarth Punto 2020 Owner handbook (in English)

CHANGING A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that the
corresponding fuse is intact before changing a bulb.
For the location of fuses, refer to the paragraph “If a
fuse blows” in this section;
❒before changing a bulb check the contacts for
oxidation;
❒burnt bulbs must be replaced by others of the same
type and power;
❒always check the height of the headlight beam after
changing a bulb for safety reasons.
158
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Changes or repairs to the electrical
system (electronic control units) carried
out incorrectly and without due consideration
for the technical specifications of the system
may lead to malfunctioning and generate a fire
hazard.
WARNING
Halogen lamps contain pressurised gas.
If they break, glass fragments could fly
everywhere.
WARNING
F0U135Abfig. 134
CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder, proceed as follows:
❒disconnect A-fig. 134;
❒turn the bottle anticlockwise to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection A to the canister and fit the
transparent tube B in the special compartment.
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 158

159
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Halogen bulbs must be handled by holding
the metallic part only. Touching the
transparent part of the bulb with your
fingers may reduce the intensity of the light
emitted and even compromise the life of the bulb
itself. In the event of accidental contact, wipe the
bulb with an alcohol-soaked cloth and leave to dry.
fig. 135F0U137Ab
IMPORTANT The internal surface of the light may
appear slightly misty: this does not indicate a fault, and is
actually caused by low temperature and the degree of
humidity in the air. Misting will rapidly disappear when
the headlights are switched on. The presence of drops
inside the headlights indicates infiltration of water.
Contact an Abarth Dealership.
TYPES OF BULBS
Different types of bulbs fig. 135 are installed on the car:
A Glass bulbs: clipped into position.
Pull to remove.
B Bayonet type bulbs: to remove this type of bulb from
its holder, press the bulb and turn it anticlockwise.C Tubular bulbs: release them from their contacts to
remove.
D-E Halogen bulbs: to remove the bulb, release the clip
holding the bulb in place.
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 159

F0U138Abfig. 136F0U139Abfig. 137
IMPORTANT You can replace the front direction
indicator, main beam and dipped beam headlight bulbs
through the access flap (see “Direction indicators” in
this section).
SIDE LIGHTS fig. 137
To change the bulb, proceed as follows:
❒remove the rubber cap using the tab;
❒press in tabs B and remove the bulb holder;
❒remove the bulb C and replace it;
❒refit the bulb holder and then refit the cap, ensuring
that it locks into place.
REPLACING EXTERIOR BULBS
For the type of bulb and power rating, see “Changing
a bulb”.
FRONT LIGHT CLUSTERS fig. 136
The front light clusters contain sidelights, dipped beam,
main beam and direction indicator bulbs.
The bulbs are arranged inside the light cluster as
follows:
A sidelights
B daytime running lights
C direction indicators
D main beam/dipped beam headlights
161
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 161

162
F0U140Abfig. 138
DAY LIGHTS (DRL)
To change the bulb, proceed as follows:
❒turn the bulb holder A-fig. 138 anticlockwise using
the tab and pull it out;
❒remove the bulb B by pushing it in slightly and
turning it anticlockwise;
❒refit the bulb holder by putting it in its housing and
turning it clockwise until it locks into place.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U141Abfig. 139
MAIN/DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the rubber cap;
❒disconnect the central electric connector B-fig. 139
and release the bulb holder catch;
❒remove the bulb A and replace it;
❒fit the new bulb, aligning the outlines of the metallic
part with the grooves on the reflector;
❒refit the bulb holder catch and reconnect the
electrical connector;
❒refit the cap A, ensuring that it locks into place.
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 162

163
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U143Abfig. 141
A
A
B
F0U142Abfig. 140
DIRECTION INDICATORS
Front fig. 140
To change the bulb, proceed as follows:
❒steer the right/left wheel inwards;
D
F0U144Abfig. 142
❒unscrew the catch A-fig. 140, then lift off the access
lid B;
❒remove the bulb holder cover C-fig. 141 by turning
it anticlockwise;
❒remove the bulb D-fig. 142 by pushing it in gently
and turning anticlockwise (“bayonet” fitting), then
replace it;
❒refit the bulb holder cover C-fig. 141 by turning it
clockwise and locking it correctly;
❒close the flap B-fig.140 then screw in the catch A.
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 163

164
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
C
AC
B
C
F0U147Abfig. 144
❒loosen the fixing screws C and remove the
headlamp;
❒remove the bulb A-fig.145 by rotating it
anticlockwise and disconnect the electrical
connector.
F0U145Abfig. 143
Side fig. 143
To change the bulb, proceed as follows:
❒slide the lens A towards the front of the car to
compress the internal clip B, then pull the unit
outwards;
❒turn the bulb holder C anticlockwise,
extract the pressure-fit bulb D and replace it;
❒refit the bulb holder C into the lens by turning it
clockwise;
❒refit the unit making sure that the internal clip B
clicks into place.
FRONT FOG LIGHTS
(for versions/markets, where provided)
To replace the bulb:
❒loosen the screw A-fig.144 and remove the
protection template B;
A
F0U146Abfig. 145
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 164

165
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
REAR LIGHT CLUSTERS
The rear light clusters contain side light (LED), brake
light and direction indicator bulbs.
The bulbs are arranged inside the light cluster fig. 146 as
follows:
D direction indicators
E brake lights
F0U148Abfig. 146F0U149Abfig. 147
To change a bulb proceed as follows:
❒undo both fixing screws A-fig 146;
❒disconnect the central electric connector B and pull
the lens unit outwards;
❒detach the bulb holder by unclipping the fasteners C-
fig. 147;
❒remove the bulb by pushing it in gently and turning
anticlockwise (“bayonet” fitting), then replace it;
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 165

168
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U154Abfig. 152
INTERNAL BULB REPLACEMENT
For the type of bulb and relevant power rating, see
“Changing a bulb”.FRONT COURTESY LIGHT
Proceed as follows to replace the bulbs:
❒act on the points shown by the arrows and remove
light A-fig. 152;
❒open the protective flap B-fig 153;
❒replace bulbs C-fig. 153 by releasing them from the
side contacts and making sure that new bulbs are
correctly locked between these contacts;
❒close the flap B-fig. 153 and fix the courtesy light A-
fig. 152 in its housing, making sure it is locked
correctly.
F0U155Abfig. 153
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 168

174
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
7.5
7.5
5
5
10
5
20
20
20
20
5
5
7.5 1
8
13
2
5
11
4
6
14
7
12
3
10
FUSE SUMMARY TABLE
Dashboard fuse box fig. 157
USERSFUSE AMPERE
Right dipped headlamp
Left dipped beam headlight, headlight alignment corrector
INT/A supply for switch coils on engine fuse box
and relay switch coils on body computer control unit
Courtesy light, boot light, glove compartment light
Supply and battery for EOBD diagnosis, automatic climate
control unit, alarm, radio, Blue&Me™ control unit
INT supply for instrument panel, switch on brake pedal
(NO contact), third brake light
Door locking/unlocking motors, dead lock activation motors, boot
unlocking motor
Windscreen/rear window washer pump
Driver’s front electric window motor
Passenger side front electric window motor
INT supply for dashboard control lights, TMPS tyre pressure
measurement control unit, electric wing mirror movement, sunroof control
unit, my-port infotelematic system socket, electrochromic rear view mirror
Instrument panel
INT supply for brake pedal switch (NC contact), clutch
pedal switch, interior heating unit, Blue&Me™ control unit,
sound system wiring, voltage stabiliser control unit, reverse light on bumper,
brake servo sensor, relay switch coils on engine compartment fusebox
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 174

181
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Before towing, switch off the steering
lock (see “Starting device” paragraph in
the “Knowing your car” section). The power
brakes and power steering will not operate
while the vehicle is being towed. More effort on
the brake pedal and steering wheel will
therefore be required. Do not use flexible cables
when towing and avoid jerky movements. While
towing, make sure not to damage parts in
contact with the car. Respect the rules of the
highway code when towing the car, specifically
in relation to the towing device and road
conduct.
WARNING
The front and rear tow hooks should be
used only for emergency operations on
the road. You are allowed to tow the car for
short distances using an appropriate device in
accordance with the highway code (a rigid bar),
to move the vehicle on the road in readiness for
towing or transporting via a breakdown vehicle.
Tow hooks MUST NOT be used to tow vehicles
off the road or where there are obstacles and/or
for towing operations using cables or other non-
rigid devices. Respecting the above conditions,
towing must take place with the two vehicles
(one towing, the other towed) aligned as much
as possible along the same centre line.
WARNING
151-182 PUNTO Abarth GB 1ed 17-07-2012 13:24 Pagina 181