brake Acura CL 2001 User Guide

During this period:Avoid full-throttle starts and rapid
acceleration.
Avoidhardbraking.Newbrakes
need to be broken-in by moderate
use f or the f irst 200 miles (300
km).
Youshouldfollowthesesamere-
commendations with an overhauled
or exchanged engine, or when the
brakes are relined. Your Acura is designed to operate on
premium unleaded gasoline with a
pump octane number of 91 or higher.
In Canada, some gasolines contain
an octane-enhancing additive called
MMT. If you use such gasolines,
your emissions control system
perf ormance may deteriorate and
the Malfunction Indicator Lamp on
your instrument panel may turn on.
If this happens, contact your
authorized Acura dealer f or service.
Help assure your car’s f uture
reliability and perf ormance by paying
extra attention to how you drive
during the f irst 600 miles (1,000 km).
Useof aloweroctanegasolinecan
cause occasional metallic knocking
noises in the engine and will result in
decreased engine perf ormance.
We recommend gasolines containing
detergent additives that help prevent
f uel system and engine deposits.
Using gasoline containing lead will
damage your car’s emissions
controls. This contributes to air
pollution.
Break-in Period, Gasoline
Bef ore Driving
Break-in Period Gasoline
160

Shift to Park or Neutral and set
the parking brake. Pull the hood
release handle located under the
lower lef t corner of the dashboard.
The hood will pop up slightly.
Screw the f uel f ill cap back on,
tighten it until it clicks several
times. If you do not properly
tighten the cap, the Malfunction
Indicator Lamp may come on (see
page ).
Push the f uel f ill door closed until
it latches.
Standing in f ront of the car, reach
in between the hood and the f ront
bumper with your f inger. The
hood latch handle is under the ‘‘A’’
logo. Slide the latch handle to the
right.
1.
2.
5.
6.
286
Service Station Procedures
Bef ore Driving
Opening the Hood
162
H H
O
OO ODD R
REEL
LEE A
A S
SEE H
HA
AN
ND DL
LEE
L
LAA T
TC
CH H H
HA
AN
ND DL
LEE

Modif ying your car, or installing
some non-Acura accessories, can
make your car unsaf e. Bef ore you
make any modif ications or add any
accessories,besuretoreadthe
f ollowing inf ormation.
Your dealer has Genuine Acura
accessories that allow you to
personalize your car. These
accessories have been designed and
approved f or your car, and are
covered by warranty.
Non-Acura accessories are usually
designed f or universal applications.
Although aftermarket accessories
may f it on your car, they may not
meet f actory specif ications, and
could adversely af f ect your car’s
handling and stability. (See
‘‘Modif ications’’ on the page f or
additional information.)When properly installed, cellular
phones, alarms, two-way radios, and
low-powered audio systems should
not interf ere with your car’s
computer-controlled systems, such
as the SRS and anti-lock brake
system.
If possible, have your dealer inspect
the f inal installation.Have the installer contact your
Acura dealer f or assistance bef ore
installing any electronic accessory. Be sure electronic accessories do
not overload electrical circuits
(see page ). Make sure the accessory does not
obscure any lights, or interf ere
with proper car operation or
perf ormance.
Bef ore installing any accessory: However, if electronic accessories
are improperly installed, or exceed
your car’s electrical system capacity,
they can interfere with the operation
of your car, or even cause the
airbags to deploy.
168 289
A ccessories
A ccessories and Modif ications
Bef ore Driving167
Improper accessories or
modifications can affect your
car’s handling, stability and
performance, and cause a
crash in which you can be hurt
or killed.
Follow all instructions in this
owner’s manual regarding
accessories and modifications.

Do not remove any original
equipment or modif y your car in any
way that would alter its design or
operation. This could make your car
unsaf e and illegal to drive.
Such modif ications can adversely
af f ect handling, and interf ere with
the operation of the car’s anti-lock
brakes and other systems.Covering the outside edge of a
f ront seat-back, with a non-Acura
seat cover for example, could
prevent the airbag from inflating
properly.
For example, do not make any
modif ications that would change the
ride height of your car, or install
wheels and tires with a dif f erent
overall diameter.
In addition, any modif ications that
decrease ground clearance increase
the chance of undercarriage parts
striking a curb, speed bump, or other
raised object, which could cause
your airbags to deploy. Do not modif y your steering wheel
or any other part of your
Supplemental Restraint System.
Modif ications could make the
system inef f ective.
Any object
attached to or placed on the covers
marked ‘‘SRS AIRBAG,’’ in the
center of the steering wheel and
on top of the dashboard, could
interf ere with the proper operation
of the airbags. Or, if the airbags
inf late, the objects could be
propelled inside the car and hurt
someone. If a side airbag
inflates,acupholderorotherhard
object attached on or near the
door could be propelled inside the
car and hurt someone.
Modif ications
Additional Saf ety Precautions
Do not place any object s over t heoutsideedgeof afront seat-back.
Do not at t ach or place object s on
the f ront airbag covers. Do not at t ach hard object s on or
near a door.
A ccessories and Modif ications
Bef ore Driving168

This section gives you tips on
starting the engine under various
conditions, and how to operate the
automatic transmission. It also
includes important inf ormation on
parking your car, the braking system,
the Traction Control System, the
Vehicle Stability Assist System, and
f acts you need if you are planning to
tow a trailer.........................
Preparing to Drive . 174
.......................
Starting the Engine . 175
Starting in Cold Weather ....................
at High Altitude . 175
..............
Automatic Transmission . 176
.
Shif t Lever Position Indicator . 176
................
Shif t Lever Positions . 177
..............
Engine Speed Limiter . 182
....................
Shif t Lock Release . 183
...........................................
Parking . 184
.....................
The Braking System . 185
.............
Brake Wear Indicators . 185
...............
Brake System Design . 186
.......................
Anti-lock Brakes . 186
Important Saf ety .........................
Reminders . 187
........................
ABS Indicator . 187
..............
Traction Control System . 188
...
Vehicle Stability Assist System . 191
...............
Driving in Bad Weather . 194
...........................
Towing a Trailer . 196
Driving
Driving173

Push the accelerator pedal half-
way to the f loor and hold it there
while starting the engine. Do not
hold the ignition key in START
(III) f or more than 15 seconds.
When the engine starts, release
the accelerator pedal gradually as
the engine speeds up and smooths
out.
If the engine fails to start in step 2,
push the accelerator pedal to the
f loor and hold it there while you
try to start the engine for no more
than 15 seconds. If the engine
does not start, return to step 2.
If the engine still does not start,
press the accelerator pedal all the
way down and hold it there while
starting in order to clear f looding.
As bef ore, keep the ignition key in
the START (III) position f or no
more than 15 seconds. Return to
step 5 if the engine does not start.
If it starts, lif t your f oot of f the
accelerator pedal so the engine
does not race.
An engine is harder to start in cold
weather. The thinner air f ound at
high altitude above 8,000 f eet (2,400
meters) adds to the problem.
Use the f ollowing procedure: Turn of f all electrical accessories
to reduce the drain on the battery.
Apply the parking brake.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.
Make sure the shif t lever is in
Park. Press on the brake pedal.
Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. If the engine
does not start right away, do not
hold the key in START (III) f or
more than 15 seconds at a time.
Pause f or at least 10 seconds
bef ore trying again.
If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed half-way
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.
1.
2.
3.
4.
5.
6.
1.2.
3.
Starting in Cold Weather at High
A ltitude (A bove 8,000 f eet/
2,400 meters)
Driving
Starting the Engine
175

CONT INUED
The shif t lever has nine positions. It
must be in Park or Neutral to start
the engine. When you are stopped in
D,D,D,2,1,N,R,orthe
Sequential SportShif t mode, press
f irmly on the brake pedal and keep
your f oot of f the accelerator pedal.To select the Sequential SportShif t
mode, slide the shif t lever toward the
lef t f rom the ‘‘D ’’ position.
In this mode the shif t lever allows
youtoshiftupanddownmanually.
YoucannotshiftoutofParkwiththe
brake pedal depressed when the
ignition switch is in LOCK (0) or
ACCESSORY (I). Whenever you move the shif t lever,
slide it along the guide on the
console.
543 5
To shift from:
PtoR
RtoN
NtoD
DtoD
DtoD Dto22to1
1to2
2toD
DtoD
DtoD DtoN NtoRRtoP Do this:
Press the brake pedal, then
move the shift lever.
Move the lever.
5
54
43 3
3
34
45 5
Automatic Transmission
Driving
Shif t L ever Positions
177
S SH H I
IFFT T L
LEE V
V E
ER
R
S
SE EQ
QU UEEN
NT TI
IAA L
L
S
SP PO
OR RTTS
SH H I
IFFT T
M
M O
ODDE
E
P
P O
OS SIITT I
IOON N

µµ
µµ
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Move the shif t
lever to the right to shif t out of the
Park position.
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can remove the key
from the ignition switch. To shif t to Reverse
f rom Park, see the explanation under
Park. To shif t to Reverse f rom
Neutral, come to a complete stop and
then shift.
If you have done all of the above and
still cannot move the lever out of
Park, see Shif t Lock Release on page . Your car has a reverse lockout so
you cannot accidentally shif t to
Reverse from Neutral or any other
driving position when the vehicle
speed exceeds 7 9 mph (12 14
km/h).
If you cannot shif t to Reverse when
the car is stopped, press the brake
pedal and slowly shif t to Neutral, and
then to Reverse.
If there is a problem in the reverse
lockout system, or your car’s battery
is disconnected or goes dead, you
cannot shif t to Reverse. (Ref er to
Shif t Lock Release on page ).
183
183
Automatic Transmission
Driving
Park (P)Reverse (R)
178

µ
µ µ
´
´
µ
µ
CONT INUED
Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to Park posi-
tion if you need to leave the car for
any reason. Press on the brake pedal
when you are moving the shif t lever
f rom Neutral to another gear.
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear for your speed and
acceleration. You may notice the
transmission shif ting up at higher
speeds when the engine is cold. This
helps the engine warm up f aster. With
the shif t lever in ‘‘D ’’ position, you
can select the Sequential SportShif t
mode to shif t gears; much like a
manual transmission, but without a
clutch pedal.
Even with the Sequential SportShift
Mode selected, the transmission will
automatically upshif t and downshif t
between f irst and second gear.
To enter the Sequential SportShif t
mode, move the shif t lever to the lef t.
To return to ‘‘D ’’, move the shif t
lever to the right.
When you move the shif t lever f rom
‘‘D ’’ to the Sequential SportShift
mode, the display shows the selected
gear.
In the Sequential SportShif t mode,
each time you push f orward on the
shif t lever, the transmission shif ts to
a higher gear. Pull back on the lever
to downshif t. The number of the
gear selected is displayed next to the
‘‘D ’’ indicator (see page ).
176
5
5
5
5
Automatic Transmission
Driving
Neutral (N)
Drive (D )
5
Sequent ial Sport Shif t Mode
179
D D o
ow
wn ns
shh i
iff t
t
U
Up
ps
shh i
iff t
t

If you need to use the Shif t Lock
Release, it means your car is
developing a problem. Have the car
checked by your Acura dealer.
This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work. This procedure
also releases the Reverse Lockout.
Set the Parking brake.
Make sure the ignition switch is in
the OFF (0) position.
To release the Reverse Lockout,
make sure the ignition switch is in
the ACCESSORY (I) position.
Put a cloth on the edge of the Shif t
Lock Release slot cover next to
the shift lever.
Use a small flat-tipped screwdriver
or small metal plate (neither are
included in the tool kit) to remove
the cover. Caref ully pry of f the
edge of the cover. Insert a screwdriver in the Shif t
Lock Release slot.
Push down on the screwdriver and
move the shift lever out of Park to
Neutral.
To release the Reverse Lockout,
move the shift lever from Neutral
to Reverse, then Park.
Remove the screwdriver f rom the
Shif t Lock Release slot, then
reinstall the cover. Make sure the
notchonthecoverisontheright
side. Depress the brake pedal and
restart the engine.
1.
2.
3.
4.
5.6.
Driving
Automatic Transmission
Shif t L ock Release
183
S SH
H I
IFFT T L
LOOC CKK R
REEL
LEE A
A S
SEE S
SLLOOT T
C
CO OV VE
ER
R