light Acura CL 2001 Manual Online

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on page
.)
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently. 300
A ir Condit ioning Syst em
Maint enance241
A AI
IRR C
COON NDDI
ITT I
IOON NIINNG G C
COON NDDE
EN
NS SEER
R
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.

Check the operation of your car’s
exterior lights at least once a month.
A burned out bulb can create an
unsaf e condition by reducing your
car’s visibility and the ability to
signal your intentions to other
drivers.
Lights
Maint enance250
S SIIDD E
E M
M A
AR
RKKEER
R L
LIIGGH HT
T
L
LO
OW W B
BEEA
A M
M
H
H E
EA
A D
DL
LIIGGH HT
T T
T
U
UR RNN S
SIIGGN NAAL
L//
P
P A
A R
RKKIINNG G L
LIIGGH HT
T
R
RO OA AD
D L
LAA M
M P
P
H
H
I
IGGH H B
BEEA
A M
M H
HE
EA
A D
DL
LIIGGH HT
T

Check the f ollowing:
If youfindanybulbsareburnedout,
replace them as soon as possible.
Refer to the chart on page to
determinewhattypeof replacement
bulb is needed.Headlights (low and high beam)
Road lamps
Parking lights
Taillights
Brake lights
Turn signals
Back-up lights
Hazard light f unction
License plate light
Side marker lights
High-mount brake light
Daytime running lights (Canadian
models)
301
Lights
Maint enance251
H HI
IGGH H-
-M
M O
OUUNNTT B
BRRAA K
KEE L
LIIGGH HT
T
T
T U
UR RNN S
SIIGGN NAAL
L L
LIIGGH HT
T B
BAA C
CKK--U
UP P L
LIIGGH HT
T
L
LIICCE EN
NS SEE P
PL
LAA T
TE
E L
LIIGGH HT
T
S
ST TO
OP P/
/T
T A
A I
ILL/ /S
SI IDD E
E M
M A
AR
RKKEER
R L
LIIGGH HT
TS
S S
ST
TO
OP P/
/T
T A
A I
ILLL LIIGGH HT
TS
S

Halogen bulbs are used f or the high
beam headlight bulbs. When
replacing a high beam headlight bulb,
handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
cartoyourdealertohaveitreplaced. Open the hood.
Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb. If you need to change a bulb on
the driver’s side, remove the
radiator reserve tank.
1.
2.
Lights
Maintenance
Replacing a High Beam Headlight
Bulb
252
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Reinstall the radiator reserve tank.
3.
4. 5.
6.
7.
Lights
Maint enance253
B BU
UL LBB
T
T A
A B
B

Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the splash shield. Pull the
splash shield down.
Remove the socket by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.Put the splash shield in place.
Reinstall the three holding clips.
Lock each clip in place by pushing
on the center.
Insert the socket and turn it one-
quarter turn clockwise to lock it in
place. Turn on the headlights to test the
new bulb.
3.
4. 5.
6.
1.
2.
Lights
Maint enance
Replacing a Road Lamp Bulb
254
H H O
OL LDD I
INNG G C
CLLIIPP S
S

If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.To remove the f ront turn signal/
parking light bulb, push it in
slightly and turn it
counterclockwise. To remove the
side marker bulb, pull it straight
out of its socket.
Install the new bulb into the
socket.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Put the inner f ender in place.
Install the two holding clips. Lock
each clip in place by pushing on
the center.
1.
2.
3.
4.5.
6.
7.
8.
9.
Lights
Maint enance
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
255
H H
O
OL LDD I
INNG G
C
CL LIIPP S
S

Open the trunk.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
Remove the f astener on the edge
of the trunk opening by turning it
counterclockwise with a coin.
Unscrew the cargo net mounting
button. Pull the lining back. Determine which of the f our bulbs
is burned out: stop/taillight, stop/
tail/side marker light, back-up
light, or turn signal.
Remove the socket by turning it
one-quarter turn counterclockwise.
1.
3. 2.4.
5.
6.
7.
Replacing Rear Bulbs
Lights
Maint enance256
F FA
A S
STTE
EN
NE ER
R C
CA
A R
RGGO O N
NEET
T
M
M O
OUUNNTTI
INNG G
B
BU UT TT
TO
ON N

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.Reinstall the socket. Turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
Put the f astener in the hole on the
side of the trunk lining and push
on the center until it locks (the
center is f lush with the head).
Screw the cargo net mounting
button back into the hole.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb in the socket.
1.
2.
8.
9.
3.
4.
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance257

Use a small Phillips-head
screwdriver to remove the two
screws. Remove the lens f rom the
license plate assembly.The courtesy lights in the doors and
roof come apart the same way. They
do not use the same type of bulb.
Removethelensbycarefully
prying on the edge of the lens with
a f ingernail f ile or a small f lat-tip
screwdriver. Do not pry on the
edge of the housing around the
lens.
Remove the bulb by pulling it
straight out. Push the new bulb
into the socket.
Put the lens back in place and
tighten the two screws securely.
1. 2.
3.
1.
Replacing a Rear License Plate
Bulb
Replacing Bulbs in the Interior
Courtesy Lights
Lights
Maint enance258
S SC
CRREEW
WS S C
CE
EI
ILLI INNG G L
LIIGGH HT
T