alternator ACURA CSX 2006 Service Owner's Manual




(#'

 )
10-11
Water Passage Replacement
C D
E B A B
A
1. Drain the engine coolant (see page 10-8).
2. Remove the alternator (see page 4-34).
3. Remove the A/C condenser fan shroud assembly.
4. Remove the A/C compressor without disconnecting
the A/C hoses (see step 40 on page 5-7).
5. Remove the intake manifold:
 K20Z2 engine (see page 9-3)
 K20Z3 engine (see page 9-7)
6. Remove the bolt (A) securing the connecting pipe.
7. Disconnect the lower radiator hose (B), the connecting pipe (C), and the water bypass hose (D),
and remove the harness clamp (E). 8. Disconnect the positive crankcase ventilation (PCV)
hose (A), then remove the water passage (B).
9. Remove the thermostat housing.
10. Remove the water pump:  K20Z2 engine (see page 10-6)
 K20Z3 engine (see page 10-7)
(cont’d)
08/08/21 14:40:00 61SNR030_100_0011
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Removal - K20Z2 engine
10-1310-13
EGR Passage Removal and
Installation
A
B
A B
C
20. Install the intake manifold:
 K20Z2 engine (see page 9-4)
 K20Z3 engine (see page 9-9)
21. Install the A/C compressor (see step 28 on page 5-19).
22. Install the A/C condenser fan shroud assembly.
23. Install the alternator (see page 4-36).
24. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
25. Clean up any spilled engine coolant. 1. Drain the engine coolant (see page 10-8).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the harness holder (A) from the bracket,
then remove the harness holder bracket (B).
4. Disconnect the upper radiator hose (A), the heater hose (B), and the water bypass hose (C).
(cont’d)
08/08/21 14:40:01 61SNR030_100_0013
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Removal - K20Z2 engine
10-1310-13
EGR Passage Removal and
Installation
A
B
A B
C
20. Install the intake manifold:
 K20Z2 engine (see page 9-4)
 K20Z3 engine (see page 9-9)
21. Install the A/C compressor (see step 28 on page 5-19).
22. Install the A/C condenser fan shroud assembly.
23. Install the alternator (see page 4-36).
24. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
25. Clean up any spilled engine coolant. 1. Drain the engine coolant (see page 10-8).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the harness holder (A) from the bracket,
then remove the harness holder bracket (B).
4. Disconnect the upper radiator hose (A), the heater hose (B), and the water bypass hose (C).
(cont’d)
08/08/21 14:40:01 61SNR030_100_0013
ProCarManuals.com
DYNOMITE -2009-

(#'


/)
Fuel and Emissions
Fuel and Emissions Systems
PGM-FI System
Electronic Throttle Control System
VTEC/VTC
Idle Control SystemFuel Supply System
Intake Air System
Catalytic Converter System
EGR System
PCV System
EVAP System..................................................
........
......................... ................
....................................... .......................
..................................................
........
......................... ................
....................................... .......................
Special Tools . 11-2
General Troubleshooting Information . 11-3
DTC Troubleshooting Index . 11-9
Symptom Troubleshooting Index . 11-13
System Description . 11-15
How to Set Readiness Codes . 11-69
..........................
.................................... ....................
......................... ........................
.................................... .............................. ....................
........................
.............................
.............................................. .........................
............................ ........
..........................
..........................
..........................................
.......................................... ..........................................................
.................................... ....................
......................... ........................
.................................... .............................. ....................
........................
.............................
.............................................. .........................
............................ ........
..........................
..........................
..........................................
.......................................... ................................
Component Location Index . 11-72
DTC Troubleshooting . 11-74
F-CAN Circuit Troubleshooting . 11-191
MIL Circuit Troubleshooting . 11-203
DLC Circuit Troubleshooting . 11-204
Injector Replacement . 11-219
A/F Sensor Replacement . 11-221
Secondary HO2S Replacement . 11-221
CMP Sensor B Replacement . 11-222
CKP Sensor Replacement . 11-222
Output Shaft (Countershaft) Speed Sensor
Replacement . 11-223
Knock Sensor Replacement . 11-223
MAP Sensor Replacement . 11-224
MAF Sensor/IAT Sensor Replacement . 11-224
ECT Sensor 1 Replacement . 11-225
ECT Sensor 2 Replacement . 11-225
ELD Replacement . 11-226
ECM/PCM Update . 11-227
ECM/PCM Replacement . 11-228
..........................
.................................... ......................
................................. ..........................
.................................... ......................
.................................
Component Location Index . 11-231
DTC Troubleshooting . 11-232
APP Sensor Signal Inspection . 11-268
Accelerator Pedal Module
Removal/Installation . 11-269
..........................
....................................
.................................................
.................................
................................. ..........................
....................................
.................................................
.................................
.................................
Component Location Index
. 11-273
DTC Troubleshooting . 11-274
VTC Oil Control Solenoid Valve Removal/Test/Installation . 11-294
CMP Sensor A Replacement . 11-295
Rocker Arm Oil Control Valve Removal/Installation . 11-296
Rocker Arm Oil Pressure Switch Removal/Installation . 11-296
..........................
.................................... .............
........................................
........................................ .................................... ...................
..........................
.................................... .............
........................................
........................................ .................................... ...................
Component Location Index
. 11-297
DTC Troubleshooting . 11-298
A/C Signal Circuit Troubleshooting . 11-306
Alternator FR Signal Circuit Troubleshooting . 11-307
Brake Pedal Position Switch Signal Circuit Troubleshooting . 11-308
Idle Speed Inspection . 11-309
ECM/PCM Idle Learn Procedure . 11-310 ..........................
.................................... .............
................................
......................................... ........................................ ......................................
.................................................
...................................................... .................................................. ....
........
................................
.............................................. .....................................................
................................. ..........................
.................................... .............
................................
......................................... ........................................ ......................................
.................................................
...................................................... .................................................. ....
........
................................
.............................................. .....................................................
.................................
Component Location Index
. 11-311
DTC Troubleshooting . 11-313
Fuel Pump Circuit Troubleshooting . 11-318
Fuel Pressure Relieving . 11-322
Fuel Pressure Test . 11-325
Fuel Tank Draining . 11-325
Fuel Line Inspection . 11-326
Fuel Line/Quick-Connect Fitting Precautions . 11-328
Fuel Line/Quick-Connect Fitting Removal . 11-329
Fuel Line/Quick-Connect Fitting Installation . 11-331
Fuel Tank Unit Removal and Installation . 11-334
Fuel Pressure Regulator Replacement . 11-337
Fuel Filter Replacement . 11-337
Fuel Pump/Fuel Gauge Sending Unit Replacement . 11-338
Fuel Tank Replacement . 11-339
Fuel Gauge Sending Unit Test . 11-340
Low Fuel Indicator Test . 11-341
..........................
......................................... .................................
.............................................................. .................
........................... .
............. ....
.............................................. ..........................
......................................... .................................
.............................................................. .................
........................... .
............. ....
..............................................
Component Location Index
. 11-342
Throttle Body Test . 11-343
Throttle Body Cleaning . 11-344
Intake Air Bypass Control Thermal Valve Test . 11-344
Air Cleaner Removal/Installation . 11-345
Air Cleaner Element Inspection/Replacement . 11-346
Intake Air Resonator Removal/Installation . 11-346
Throttle Body Removal/Installation . 11-348
Throttle Body Disassembly/Reassembly . 11-350
Intake Air Bypass Control Thermal Valve Replacement . 11-351
..........................
.................................... ...
..........................
.................................... ...
Component Location Index
. 11-352
DTC Troubleshooting . 11-353
Catalytic Converter Removal/Installation . 11-355
..........................
.................................... .........................................................
.................................... ...............................
Component Location Index
. 11-356
DTC Troubleshooting . 11-357
EGR Valve Replacement . 11-370
..........................
.................................... .........................................................
.................................... ...............................
Component Location Index
. 11-371
PCV Valve Inspection . 11-372
PCV Valve Replacement . 11-373
..........................
....................................
........................................ ........................
.............................
..............................................
.............................................. ..........................
....................................
........................................ ........................
.............................
..............................................
..............................................
Component Location Index
. 11-374
DTC Troubleshooting . 11-375
Fuel Cap Warning Message System Troubleshooting . 11-405
EVAP Canister Replacement . 11-407
FTP Sensor Replacement . 11-408
EVAP Canister Vent Shut Valve Replacement . 11-409
EVAP Canister Purge Valve Replacement . 11-409
08/08/21 14:12:30 61SNR030_110_0001
ProCarManuals.com
DYNOMITE -2009-

•••
•••
•••
•••Ó
•••
•••
•••
••• Ó
Ó
Ó
•••
••• Ó
•••
••• Ó
Ó
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
••• Ó
•••
•••
••• Ó
DTC
(MIL indication ) Two Drive Cycle
Detection Detection Item MIL Note
11-11
P0606 (0)
Engine Control Module (ECM)/Powertrain Control Module (PCM)
Processor Malfunction ON (see page 11-145)
P060A (131) Powertrain Control Module (PCM) (A/T System) Internal Control
Module Malfunction ON (see page 11-145)
P062F (131) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Internal Control Module Keep Alive Memory (KAM) Error ON (see page 11-144)
P0630 (139) VIN Not Programmed or Mismatch ON (see page 11-146)
P0685 (135) Engine Control Module (ECM)/Powertrain Control Module (PCM)
Power Control Circuit/Internal Circuit Malfunction ON (see page 11-147)
P0720 (122) Output Shaft (Countershaft) Speed Sensor Circuit Malfunction ON (see page 11-148)
P0720 (122) Output Shaft (Countershaft) Speed Sensor Circuit Malfunction ON (see page 11-149)
P1009 (56) Variable Valve Timing Control (VTC) Advance Malfunction ON (see page 11-283)
P1109 (13) Barometric Pressure (BARO) Sensor Circuit Out of Range High ON (see page 11-152)
P1116 (86) Engine Coolant Temperature (ECT) Sensor 1 Circuit Range/
Performance Problem ON (see page 11-153)
P1128 (5) Manifold Absolute Pressure (MAP) Sensor Signal Lower Than
Expected ON (see page 11-155)
P1129 (5) Manifold Absolute Pressure (MAP) Sensor Signal Higher Than
Expected ON (see page 11-156)
P1157 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) AFS Circuit High Voltage ON (see page 11-157)
P1172 (61) Air Fuel Ratio (A/F) Sensor (Sensor 1) Circuit Out of Range High ON (see page 11-159)
P1297 (20) Electrical Load Detector (ELD) Circuit Low Voltage OFF (see page 11-160)
P1298 (20) Electrical Load Detector (ELD) Circuit High Voltage OFF (see page 11-162)
P1454 (91) Fuel Tank Pressure (FTP) Sensor Circuit Range/Performance Problem ON (see page 11-402)
P145C (90) Evaporative Emission (EVAP) System Purge Flow Malfunction ON (see page 11-404)
P1549 (34) Charging System High Voltage OFF (see page 11-164)
P1658 (40) Electronic Throttle Control System (ETCS) Control Relay ON
Malfunction ON (see page 11-241)
P1659 (40) Electronic Throttle Control System (ETCS) Control Relay OFF
Malfunction ON (see page 11-243)
P1683 (40) Throttle Valve Default Position Spring Performance Problem ON (see page 11-247)
P1684 (40) Throttle Valve Return Spring Performance Problem ON (see page 11-248)
P16BB (116) Alternator B Terminal Circuit Low Voltage OFF (see page 11-165)
P16BC (116) Alternator FR Terminal Circuit/IGP Circuit Low Voltage OFF (see page 11-166)
P2101 (40) Electronic Throttle Control System (ETCS) Malfunction ON (see page 11-249)
P2118 (40) Throttle Actuator Current Range/Performance Problem ON (see page 11-251)
P2122 (37) Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP)
Sensor D) Circuit Low Voltage ON (see page 11-253)
P2123 (37) Accelerator Pedal Position (APP) Sensor A (Throttle Position (TP)
Sensor D) Circuit High Voltage ON (see page 11-256)
P2127 (37) Accelerator Pedal Position (APP) Sensor B (Throttle Position (TP)
Sensor E) Circuit Low Voltage ON (see page 11-257)
P2128 (37) Accelerator Pedal Position (APP) Sensor B (Throttle Position (TP)
Sensor E) Circuit High Voltage ON (see page 11-260)
P2135 (7) Throttle Position (TP) Sensor A/B Incorrect Voltage Correlation ON (see page 11-262)
P2138 (37) Accelerator Pedal Position (APP) Sensor A/B (Throttle Position (TP)
Sensor D/E) Incorrect Voltage Correlation ON (see page 11-264)
P2176 (40) Throttle Actuator Control System Idle Position Not Learned ON (see page 11-266)
P2183 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit Range/
Performance Problem ON (see page 11-168)
P2184 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit Low Voltage ON (see page 11-170)
P2185 (192) Engine Coolant Temperature (ECT) Sensor 2 Circuit High Voltage ON (see page 11-172)
P2195 (48) Air Fuel Ratio (A/F) Sensor (Sensor 1) Signal Stuck Lean ON (see page 11-174)
NOTE:  The above DTCs are indicated when the PGM-FI system is selected with the HDS.
 Some automatic transmission DTCs cause the MIL to come on. If the MIL is on and no DTCs are indicated in the PGM-FI system, select the A/T system, and check for automatic transmission DTCs.
: These DTCs are indicated by a blinking MIL when the SCS line is jumped with the HDS.
1: A/T
2: The D indicator and the MIL may come on at the same time (A/T).
3: M/T
4: K20Z2 engine
5: K20Z3 engine
9: ’09 model
(cont’d)
1
9
1, 2
3
4
5
5
3
1
08/08/21 14:12:36 61SNR030_110_0011
ProCarManuals.com
DYNOMITE -2009-

(#')
Symptom Diagnostic procedure Also check for
11-13
Symptom Troubleshooting Index
When the vehicle has one of these symptoms, check for a diagnostic trouble code (DTC) with the HDS. If there is no
DTC, do the diagnostic procedure for the symptom, in the sequence listed, until you find the cause.












Engine will not start
(MIL works OK, no DTCs set)
1.
2.
3.
4.Test the battery (see page 22-67).
Test the starter (see page 4-9).
Check the fuel pressure (see page 11-325).
Troubleshoot the fuel pump circuit (see page 11-
318).Low compression
No ignition spark
Intake air leaks
Locked up engine
Broken cam chain
Fuel contamination
Engine will not start
(MIL comes on and stays on,
no DTCs set) Troubleshoot the DLC circuit (see page 11-204).
MIL comes on and stays on,
or never comes on at all, no
DTCs set Troubleshoot the MIL circuit (see page 11-203).
Engine will not start
(MIL works OK, no DTCs set,
immobilizer indicator stays
on or flashes) Check the immobilizer system (see page 22-321).
Engine starts but stalls
immediately
(MIL works OK, no DTCs set,
immobilizer indicator stays
on or flashes) Check the immobilizer system (see page 22-323).
Engine is hard to start
(MIL works OK, no DTCs set) 1.
2.
3.Test the battery (see page 22-67).
Check the fuel pressure (see page 11-325).
Clean the throttle body (see page 11-
344).Low compression
Intake air leaks
Fuel contamination
Weak spark
Cold fast idle too low
(MIL works OK, no DTCs set) 1.
2.
3.DotheECM/PCMidlelearnprocedure(seepage
11-310).
Check the idle speed (see page 11-309).
Clean the throttle body (see page 11-
344).
Cold fast idle too high
(MIL works OK, no DTCs set) 1.
2.
3.DotheECM/PCMidlelearnprocedure(seepage
11-310).
Check the idle speed (see page 11-309).
Do the throttle position learning check (see page
11-343). Intake air leaks
Idle speed fluctuates
(MIL works OK, no DTCs set) 1.
2.
3.
4.DotheECM/PCMidlelearnprocedure(seepage
11-310).
Check the idle speed (see page 11-309).
Do the carbon accumulation check (see page 11-343).
Troubleshoot the A/C signal circuit (see page 11-306). Incorrect valve
timing or clearance
adjustment
Intake air leaks
After warming up, idle speed
is below specification without
load
(MIL works OK, no DTCs set) 1.
2.
Troubleshoot the alternator FR signal circuit
(see page 11-307).
Do the carbon accumulation check (see page 11-343). Incorrect valve
timing or clearance
adjustment
After warming up, idle speed
is above specification without
load
(MIL works OK, no DTCs set) 1.
2.
Troubleshoot the alternator FR signal circuit
(see page 11-307).
Inspect the APP sensor (see page 11-268). Intake air leaks
(cont’d)
08/08/21 14:12:36 61SNR030_110_0013
ProCarManuals.com
DYNOMITE -2009-

Î
´
ECM/PCM Electrical Connections
11-16Fuel and Emissions Systems
System Description (cont’d)
IGNITION
SWITCH
IG1
ST B
IG2
IG1 HOT in ON (II)
and START (III) IGNITION COIL
RELAY
ELD PGM-FI MAIN
RELAY 2 (FUEL PUMP)P
FUEL PUMP
PGM-FI MAIN
RELAY 1
BATTERY A/C CONDENSER
FAN RELAYRADIATOR
FAN RELAY
A/C COMPRESSOR
CLUTCH RELAY
To
COOLING
FAN CONTROL
RELAY E
A8 IGPC36 IG1
A14 ACC
A5 FANH A23 ELD
A4 FANL GF
C
B
D
A
PG1 B36PG2 B1
MRLY A6
IMOFPR A15
SUBRLY A21
ETCSRLY A20 STARTER CUT
RELAY (ST CUT)
PGMETCS C2 PGM-FI
SUBRELAY
ETCS CONTROL
RELAY
I
IG1ETCS C1
ECM/PCM
CLUTCH
INTERLOCK
SWITCH
H
J*2
*1
T
*3
*1: A/T
*2: M/T
*3: K20Z3 engine
UNDER-HOOD
FUSE/RELAY BOX:
No. 1 MAIN FUSE (100 A)
No.19FIMAIN(15A)
No. 2 IG MAIN (50 A)
No. 23 BACK UP (10 A)
No. 12 STOP & HORN
(15 A) No. 18 IG COIL (15 A)
UNDER-DASH
FUSE/RELAY BOX: No. 3 ALTERNATOR
(10 A) No. 2 FUEL PUMP (15 A)
No. 36 IG2 HAC (A/C)
(10 A)
UNDER-HOOD
FUSE/RELAY BOX: No.15OILLVL(7.5A)
No. 11 FI SUB (15 A)
No. 21 DBW (THROTTLE
ACTUATOR CONTROL) (15 A)
08/08/21 14:12:37 61SNR030_110_0016
ProCarManuals.com
DYNOMITE -2009-


´µ
ECM/PCM Electrical Connections (cont’d)
11-18 Fuel and Emissions Systems
System Description (cont’d)
D
C
EVAP CANISTER
PURGE VALVE
EVAP CANISTER
VENT SHUT VALVE
ALTERNATOR
ICM
To
SPARK
PLUG
No. 1 IGNITION COIL
To
SPARK
PLUG ICM
No. 2 IGNITION COIL
To
SPARK
PLUG ICM
No. 3 IGNITION COIL
To
SPARK
PLUG ICM
No. 4 IGNITION COIL A10 VSV B3 PCS
B42 ALTL
B43 ALTF
C15 IGPLS1
C16 IGPLS2
C17 IGPLS3
C18 IGPLS4 B41 ALTC LG1 C40 I
VTS B34 ROCKER ARM
OIL CONTROL
SOLENOID
VTC C23
AFSHTC C9
AFS C29
SHO2S C27
SO2SHTC B4
LG2 C44
AFS C30
SECONDARY
HO2S
(SENSOR 2) A/F SENSOR
(SENSOR 1)
S-NET5V A44 G
CMPA C41 K
Q
CMP SENSOR A
ROCKER ARM
OIL PRESSURE
SWITCH
P
VTPSW C22 VTC OIL CONTROL
SOLENOID VALVE
To MICU
08/08/21 14:12:38 61SNR030_110_0018
ProCarManuals.com
DYNOMITE -2009-

´´ µ
´µ µ
µ µ
µµ µ
µ
µ
ÎÚ
ECM/PCM Inputs and Outputs at Connector B ( ) (44P)
Terminal
numberWire color Terminal name DescriptionSignal
11-30Fuel and Emissions Systems
System Description (cont’d)
NOTE: Standard battery voltage is about 12 V.


30 RED/BLK VG (MASS AIR FLOW
(MAF) SENSOR SIDE) Detects MAF sensor signal At idle: about 1.1 1.6 V
(between VG terminal and VG terminal)
31 RED/YEL IAT (INTAKE AIR TEMPERATURE (IAT)
SENSOR) Detects IAT sensor signal With ignition switch ON (II): about 0.1 4.0 V
(about 1.8 V at normal operating temperature)
32 BLK/BLU VG (MASS AIR FLOW (MAF) SENSOR SIDE) Ground for MAF sensor
signal
33 GRN/BLK SG2 (SENSOR GROUND) Sensor ground Less than 1.0 V at all times
34 GRN/YEL VTS (ROCKER ARM OIL CONTROL SOLENOID) Drives rocker arm oil
control solenoidAt idle: about 0 V
35 BRN LSB (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE B) Drives A/T clutch pressure
control solenoid valve B
With ignition switch ON (II): current controlled
36 BLK PG1 (POWER GROUND) Ground circuit for ECM/ PCMLess than 1.0 V at all times
40 BRN SDNP (PADDLE SHIFTER (DOWN SHIFT SWITCH)) Detects paddle shifter
(downshift switch) signalIn S:
With paddle shifter (downshift switch) pressed:
about 0 V
With paddle shifter (downshift switch) released:
about 5.0 V
41 WHT/GRN ALTC (ALTERNATOR CONTROL) Sends alternator control
signalWith warmed up engine running: about 5.0 V
(depending on electrical load)
42 WHT/BLU ALTL (ALTERNATOR L SIGNAL) Detects alternator L signal With ignition switch ON (II): about 0 V
With engine running: battery voltage
43 WHT/RED ALTF (ALTERNATOR FR SIGNAL) Detects alternator FR signal With engine running: about 2.6 3.4 V
(depending on electrical load)
44 RED/BLK LSA (A/T CLUTCH PRESSURE CONTROL
SOLENOID VALVE A) Drives A/T clutch pressure
control solenoid valve A
With ignition switch ON (II): current controlled
1: A/T
1
1
1
Terminal side of female terminals
08/08/21 14:12:44 61SNR030_110_0030
ProCarManuals.com
DYNOMITE -2009-

Throttle Body
Brake Pedal Position Switch
Electrical Power Steering (EPS) Signal
Fuel Cutoff Control
Fuel Pump Control
PGM-FI Main Relay 1 and 2
Idle Control System
Fuel Supply System
11-36Fuel and Emissions Systems
System Description (cont’d)
THROTTLE VALVE
THROTTLE POSITION
(TP) SENSOR and
THROTTLE ACTUATOR
The throttle body is a single-barrel side draft type. The
lower portion of the throttle valve is heated by engine
coolant from the cylinder head to prevent icing of the
throttle plate. When the engine is cold, the A/C compressor is on, the
transmission is in gear, the brake pedal is pressed, the
power steering load is high, or the alternator is
charging, the ECM/PCM sends signal to the throttle
position to maintain the correct idle speed.
The brake pedal position switch signals the ECM/PCM
when the brake pedal is pressed.
The EPS signals the ECM/PCM when the power steering
load is high.
During deceleration with the throttle valve closed,
current to the injectors is cut off to improve fuel
economy at engine speeds over 1,000 rpm. Fuel cutoff
control also occurs when the engine speed exceeds
6,900 rpm (K20Z3: 8,200 rpm), regardless of the
position of the throttle valve, to protect the engine from
over-revving. When the vehicle is st
opped, the ECM/
PCM cuts the fuel at engine speeds over 5,000 rpm
(K20Z3: 7,700 rpm). On a cold engine, fuel cut occurs at
a lower engine speed.
When the ignition switch is turned to ON (II), the ECM/
PCM grounds PGM-FI main relay 2 (FUEL PUMP) which
feeds current to the fuel pump for 2 seconds to
pressurize the fuel system. With the engine running, the
ECM/PCM grounds PGM-FI main relay 2 (FUEL PUMP)
and feeds current to the fuel pump. When the engine is
not running and the ignition is turned to ON (II), the
ECM/PCM cuts ground to PGM-FI main relay 2 (FUEL
PUMP) which cuts current to the fuel pump.
PGM-FI main relay 1 is energized whenever the ignition
switch is ON (II), to supply battery voltage to the ECM/
PCM, power to the injectors, and power for PGM-FI
main relay 2 (FUEL PUMP). PGM-FI main relay 2 (FUEL
PUMP) is energized to supply power to the fuel pump
for 2 seconds when the ignition switch is turned to
ON (II), and when the engine is cranking or running.
08/08/21 14:13:39 61SNR030_110_0036
ProCarManuals.com
DYNOMITE -2009-