Battery ACURA CSX 2006 Service Repair Manual




(#'


)
22-296 Accessory Power Sockets
Front Accessory Power Socket Test/Replacement
BLK
WHT
A B
A
A
NOTE: If both of the front and console accessory power
sockets do not work, check the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box. 1. Remove the center panel.  With audio:– ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
 With navigation: – ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
2. Disconnect the 2P connector (A) from the front accessory power socket (B).
3. Inspect the connector terminals to be sure they are all making good contact.
 If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
 IftheterminalslookOK,gotostep4.
4. Turn the ignition switch to ACC (I).
5. Measure the voltage between front accessory power socket 2P connector terminal No. 1 and body
ground. There should be battery voltage.
 If there is battery voltage, go to step 6.
 If there is no voltage, check for: – Blown No. 29 (15 A) fuse in the under-dash fuse/relay box.
– Faulty front accessory power socket relay.
– Poor ground (G 503).
– Anopeninthewire. 6. Check for continuity between front accessory
power socket 2P connector terminal No. 2 and body
ground. There should be continuity.
 If there is continuity, replace the power socket; go to step 7.
 If there is no continuity, check for: – Poor ground (G 502).
– Anopeninthewire.
7. Remove the socket (A).
8. Remove the housing (A) from the panel.
9. Install the front accessory power socket in the reverse order of removal.
Wire side of
female terminals
08/08/21 14:36:08 61SNR030_220_0298
ProCarManuals.com
DYNOMITE -2009-

Î


(#'



)
22-297
Console Accessory Power Socket Test/Replacement
BLK
YEL
A
B
A
A
NOTE: If both of the front and console accessory power
sockets do not work, check the No. 35 (7.5 A) fuse in the
under-dash fuse/relay box. 1. Remove the center console (see page 20-95).
2. Disconnect the 2P connector (A) from the console accessory power socket (B).
3. Inspect the connector terminals to be sure they are all making good contact.
 If the terminals are bent, loose, or corroded, repair them as necessary and recheck the system.
 IftheterminalslookOK,gotostep4.
4. Turn the ignition switch to ACC (I), and measure the voltage between console accessory power socket
2P connector terminal No. 1 and body ground.
There should be battery voltage.
 If there is battery voltage, go to step 5.
 If there is no voltage, check for: – Blown No. 28 (15 A) fuse in the under-dash fuse/relay box.
– Faulty console accessory power socket relay.
– Poor ground (G 503).
– Anopeninthewire. 5. Check for continuity between console accessory
power socket 2P connector terminal No. 2 and body
ground. There should be continuity.
 If there is continuity, replace the power socket; go to step 6.
 If there is no continuity, check for: – Poor ground (G 601).
– Anopeninthewire.
6. Remove the socket (A).
7. Remove the housing (A) from the panel.
8. Install the console accessory power socket in the reverse order of removal.
Wire side of
female terminals
08/08/21 14:36:08 61SNR030_220_0299
ProCarManuals.com
DYNOMITE -2009-

Î(#'"
)
22-300Seat Heaters
Circuit Diagram
Q16
IG2 HOT in ON (II) G19 C3
M5
LT GRN
GRN/RED LT GRN
OFF 1
2
GRN/RED LT GRN
6
5
3
BLU
BLK HIGH
LOW
4
LT BLU GRY
LT GRN
DRIVER’S SEAT HEATER
3
YEL
BLK
BLK BLK CUSHION
1
2
2
1
BACK
BR TH DRIVER’S SEAT HEATER RELAY BOX
BLU/YEL
BRN
ORN
BLK RED
RED
RED No. 5 (15 A)
No.36(HAC)(10A)
G601
G601 IGNITION SWITCH
IG2
BAT
ORN
WHT
UNDER-HOOD FUSE/RELAY BOX
No. 2 (IG) (50 A)
No. 1 (BAT) (100 A)
BATTERY UNDER-DASH FUSE/RELAY BOX
SEAT
HEATER
RELAY
(HIGH) SEAT
HEATER
RELAY
(LOW)
No.14(7.5A)FUSE
(UNDER-DASH
FUSE/RELAY BOX)
DASH LIGHTS
BRIGHTNESS
CONTROLLER LIGHT
(LED)
INDICATOR
(LED)DRIVER’S SEAT
HEATER SWITCH
INDICATOR
(LED)
H1
G1
1 4
2 343
1 5
2
No. 2 (OP) (80 A) *1
(60 A) *2 WHT*1
RED*2
BLU
BLU*1
ORN*2 GRN*1
BRN*2 MICU
08/08/21 14:36:48 61SNR030_220_0302
ProCarManuals.com
DYNOMITE -2009-


(#'
)
22-305
Circuit Diagram
C3 N11
G12
DEFOGGER
DEFOGGER 4
6
ORN
BRN
BRNBRN
G503 G502
PUR
PNK BLK PURBLUBLK1
6
8
1
6
8 2
7
2
7
GRN
ORN ORN
WHT
BLK
G503 BLK
BLK
UP RIGHTLEFT
DOWN
RIGHT MIRROR
LEFT MIRROR POWER MIRROR SWITCH
BRN LT GRN
IG2 HOT in ON (II)
BLU
PNK
LT GRN WHT
DOWN LEFT
RIGHT
UP IGNITION SWITCH
BAT
IG2
UNDER-HOOD FUSE/RELAY BOX
No. 2 (IG) (50 A)
BATTERY
ORN
2
DOWN RIGHT
LEFT UP
RIGHT
LEFT LEFTRIGHT
5
PUR 10 11
12 139
WHT
No. 1 (BAT) (100 A)
UNDER-DASH
FUSE/RELAY BOX
No. 1 (7.5 A) FUSE
(UNDER-DASH
FUSE/RELAY BOX)
CLIMATE
CONTORL
UNIT LIGHT
(LED)
POWER MIRROR
DEFOGGER
RELAY
UNDER-HOOD
FUSE/RELAY BOX H1
D7 E2
F8 F15 No.36(HAC)(10A)
08/08/21 14:36:51 61SNR030_220_0307
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
Both mirrors Left mirror
Right mirror
Defogger
22-306Power Mirrors
Function Test
BLK
WHTGRN
WHTPNK BLU PUR
BRN
BLK
A
B
1. Remove the power window master switch (A).
2. Disconnect the 13P connector (B) from the powermirror switch.
3. Choose the appropriate test based on the symptom:
 Both mirrors don’t work, go to step 4.
 Leftmirrordoesn’twork,gotostep6.
 Right mirror doesn’t work, go to step 7.
4. Measure the voltage between terminal No. 2 and body ground with the ignition switch turned to ON
(II).
There should be battery voltage.
 If there is no voltage, check for: – Blown No. 36 (10 A) fuse in the under-dash fuse/relay box.
– AnopenintheBRNwire.
 If there is battery voltage, go to step 5.
5. Check for continuity between terminal No. 6 and body ground. There should be continuity.
 If there is no continuity, check for: – AnopenintheBLKwire.
– Poor ground (G 503).
 If there is continuity, check both mirrors individually as described in the next steps. 6. Connect terminals No. 2 and No. 10, and terminals
No. 5 (or No. 12) and No. 6 with jumper wires.
The left mirror should tilt down (or swing left) with
the ignition switch to ON (II).
 If the left mirror does not tilt down (or does not swing left), check for an open in the PUR (or PNK)
wire between the left mirror and the 13P
connector.
If the wire is OK, check the left mirror actuator.
 If the mirror neither tilts down nor swings left, repair the GRN wire.
 If the mirror works properly, check the mirror switch.
7. Connect terminals No. 2 and No. 11, and terminals No. 5 (or No. 13) and No. 6 with jumper wires. The
right mirror should tilt down (or swing left) with the
ignition switch to ON (II).
 If the mirror does not tilt down (or does not swing left), check for an open in the PUR (or BLU) wire
between the right mirror and the 13P connector.
If the wire is OK, check the right mirror actuator.
 If the mirror neither tilts down nor swings left, repair the WHT wire.
 If the mirror works properly, check the mirror switch.
8. Connect the power mirror defogger relay terminals No. 1 and No. 2 in the under-hood fuse/relay box
with a jumper wire, and measure the voltage
between mirror connectors terminal No. 1 and
body ground. There should be battery voltage and
both mirrors should warm up with the ignition
switch to ON (II). If there is no voltage or neither warms up, check for:
– AnopenintheORNwire.
– Blown No. 36 (10 A) fuse in the under-dash fuse/relay box.
 If only one fails to warm up, check: – Its defogger.
– Poor ground (G 503).
 If both warm up, check the defogger switch.
Wire side of female terminals
08/08/21 14:36:52 61SNR030_220_0308
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
22-311
Circuit Diagram
IG2 HOT in ON (II) G12C3
CLIMATE CONTROL UNIT LT GRN
BLK
G603 2 BRN
LT GRN LT GRN
BLK No. 2 (IG) (50 A)
G801
1
RED RED UNDER-HOOD FUSE/RELAY BOX
G504BLK
RED
BRN
No. 8
(30 A)
No. 36
(HAC)
(10 A)
ORN
IGNITION SWITCH
IG2
BAT
WHT
BATTERY
No. 1 (BAT) (100 A)
UNDER-DASH
FUSE/RELAY
BOX
REAR
WINDOW
DEFOGGER
RELAY
REAR WINDOW
DEFOGGER
SWITCH
INDICATOR
(Rear window defogger
switch and defogger
timer circuit built into
the climate control unit.)
NOISE
CONDENSER REAR
WINDOW
DEFOGGER POWER
MIRROR
DEFOGGER
RELAY
H1
D1
J4 F17 F8
2 3
5
1
1 MICU
Q16
08/08/21 14:36:55 61SNR030_220_0313
ProCarManuals.com
DYNOMITE -2009-


(#'


)
22-312Rear Window Defogger
Function Test
A
B
About 2.0 V About 6 V About 11 V
About 8.5 V
About 4.2 V
NOTE:
 Be careful not to scratch or damage the defogger wires with the tester probe.
 Before testing, check the No. 8 (30 A) fuse in the under-hood fuse/relay box and the No. 36 (10 A) fuse
in the under-dash fuse/relay box.
1. Measure the voltage between the positive terminal (A) and body ground with the ignition switch turned
to ON (II) and the defogger switch ON.
There should be battery voltage.
 If there is no voltage, check for: – Faulty rear window defogger relay.
– Faulty climate control unit.
– An open in the RED wire to the positive terminal.
 If there is voltage, go to step 2. 2. Disconnect the negative terminal (B) from the rear
window defogger.
3. Check for continuity between the negative terminal and body ground.
If there is no continuity, check for an open in the
wire or poor ground (G 801). If there is continuity,
go to step 4.
4. Reconnect the negative terminal to the rear window defogger.
5. Turn the ignition switch to ON (II) and the rear window defogger switch ON.
6. Touch the voltmeter positive probe to each point on each defogger wire, and the negative probe to
the negative terminal.
 If the voltage is as specified, the defogger wire up to that point is OK.
 If the voltage is not as specified, repair the defogger wire.
– If it is more than specified at one of the points, there is a break in the negative half of the wire.
– If it is less than specified at one of the points, there is a break in the positive half of the wire.
08/08/21 14:36:55 61SNR030_220_0314
ProCarManuals.com
DYNOMITE -2009-

Î
(#')
µ
µ
µ
22-316Immobilizer System
Circuit Diagram
LT GRN
PNK R9
F8 LT GRN
28
21
PNK
F24 G2D2
Q1
R12
PNK R6 R16 PNK
BRN/YEL C40
BRN/YEL LG1
LG2
BRN/YEL C44 B-CAN
Q6
G504 BLK
2 1
BRN/YEL IG1
2
YEL MICU
B-CAN
VBU
K-LINE
IGKEYSW
LG
7
BLK
BRN
IG1 C36
BLK/GRN
5
LT BLU
WHT
A44
B1
B36 PG2
PG1
BLK
G101 PNK
BRN
PNK
1
No. 2 (15 A)
WHT
KEY
IMOCD
ECM/PCM UNDER-DASH FUSE/RELAY BOX
ORN IG1
BAT
BLU
No. 23 (10 A)
UNDER-HOOD FUSE/RELAY BOX
No. 2 (IG) (50 A)
BATTERY IGNITION SWITCH
No. 1 (BAT) (100 A)
IMMOBILIZER-KEYLESS CONTROL UNIT6
3 4
PGM-FI
MAIN RELAY 2
(FUEL PUMP)
DATA LINK
CONNECTOR
IGNITION
KEY SWITCH
(Closed: Key inserted)
IG1 HOT in ON (II)
and START (III)
GAUGE CONTROL
MODULE (TACH)
UNDER-DASH
FUSE/RELAY BOX IMMOBILIZER
INDICATOR
(LED)
PARKING
BRAKE
SWITCH
(Closed:
Lever pulled)
UNDER-DASH
FUSE/RELAY
BOX
D4
H1
1: CAN line
: Other communication line
*1: ’06 07 models
*2: ’07 09 models
*3: ’08 09 models
ORN
IMOES UNIT
(Built into the MICU) MICU
BLK*2
IMOCD
BLK/RED*1 BLK*3
08/08/21 14:36:58 61SNR030_220_0318
ProCarManuals.com
DYNOMITE -2009-

(#')
Symptom Troubleshooting by the Immobilizer Indicator Lighting Pattern
General Check before Troubleshooting
Normal operation
Immobilizer code is not identified
Immobilizer indicator does not come on
Immobilizer indicator does not go off
22-321
Symptom Troubleshooting Information
Immobilizer system condition can be checked by the immobilizer indicator lighting pattern.
If the immobilizer code is identified, the immobilizer indicator comes on for 2 seconds, then goes off after turning the
ignition switch to ON (II).
The immobilizer indicator does not come on when the ignition switch is turned to LOCK (0).
If the immobilizer code is not identified, the immobilizer indicator comes on for 2 seconds, then blinks after turning the
ignition switch to ON (II).
The immobilizer indicator blinks ten times, then goes off when the ignition switch is turned to LOCK (0).
If the immobilizer indicator does not come on after turning the ignition switch to ON (II), there may be an open or short
in the F-CAN lines between the ECM/PCM and the gauge control module (tach). Watch the malfunction indicator lamp
(MIL). If the MIL stays on, go to the PGM-FI system troubleshooting (see page 11- 203).
If the immobilizer indicator does not go off after turning the ignition switch to ON (II), do the gauge control m odule
(tach) self-diagnostic function (see page 22- 241). If the indicator drive circuit is OK, verify the SYSTEM CHECK with the
HDS.
Before troubleshooting the immobilizer system, check the following general points and solve any if applicable.
 Battery is low; charge the battery fully, then troubleshoot the immob ilizer system.
 Ignition key is not a genuine Honda part; use the Acura-approved key blank, register the key, then troubleshoot the immobilizer system.
 Key ring, or keys, or a key case is used; remove the key from it, and troubleshoot the immob ilizer system with a key
only.
 Aftermarket electrical part is attached; remove it, then troubleshoot the immob ilizer system.
(cont’d)
08/08/21 14:36:59 61SNR030_220_0323
ProCarManuals.com
DYNOMITE -2009-

Î
How to Troubleshoot
Symptom Troubleshooting of an open Power Supply and Ground Circuit
22-322Immobilizer System
Symptom Troubleshooting Information (cont’d)
Immobilizer
Indicator
Symptom
Line Error Engine StartKey
RegistrationTester
Communication
Keyless Operation
VBU line open
or short Comes on,
then goes off.
Possible
Possible Possible
Impossible
1
IG1 line open
or short Blinking Impossible
Impossible
Impossible
Possible
2
Blinking Impossible Impossible
Possible
Possible
IMOCD line
open or short
3
4 Immobilizer:
Possible
Keyless:
Impossible Impossible
Possible Possible
Comes on,
then goes off.
B-CAN line
open or short
Comes on,
then goes off. Impossible
Impossible
Possible
Possible
5
KEYSW line
short to groundGND (LG) line
open
6
7 (in spite of the key is
in the ignition switch)
Possible
Possible Possible Possible
Comes on,
then goes off.
KEYSW line
open
K-LINE line
open or short
Blinking Impossible Impossible
Impossible ImpossibleImpossible
Cause of
Malfunction
Terminal
No.
NOTE: If the HDS does not communicate with the vehicle, troubleshoot the DLC circuit (see page 11-
204).
1. Do the PGM-FI system DTCs check. If there are any DTCs, troubleshoot the indicated DTC.
2. Do the Body Electrical DTCs check. If there are any DTC, troubleshoot the indicated DTC.
3. Do the system check using the HDS. If there is a system check number, do the troubleshooting for the item indicated (see page 22-326).
4. Check the status log using the HDS. Troubleshoot the line with the highest counts (see page 22-328). If all the lines are ‘‘0’’ zero, the problem may not be caused by the immobilizer system, check for ignition or fuel problems.
NOTE: Once repaired, clear the status log by removing the back up power fuse, or disconnecting the battery.
If a malfunction occurs in the immobilizer circuit for the VBU, IG1 and GND (LG) lines, identify the lines to check with
this table.
08/08/21 14:37:00 61SNR030_220_0324
ProCarManuals.com
DYNOMITE -2009-