fuse box ACURA CSX 2006 Service Manual Online

Î(#'

)
17-30EPS Components
Circuit Diagram
BATTERY
GAUGE CONTROL
MODULE (TACH) IGNITION
SWITCH
WHT
UNDER-HOOD
FUSE/RELAY BOX
BRN
BLU UNDER-DASH
FUSE/RELAY BOX
DATA LINK
CONNECTOR (DLC) EPS
INDICATOR
BRN
WHT
RED
BLU
WHT
RED
WHT
RED
ORNLT BLU WHT
ECM/PCM
BRN
3
6 F16
Q9
IG1 HOT in ON (II)
and START (III) D2
B1
H1 YEL*
GRY*
No. 10 (7.5 A)
No. 2 (50 A)
No. 4 (7.5 A)
CAN-H 17
1
19
CAN-L IG1
CAN-H A28
A36
A37
CAN-L NEP
CAN-L 6
14
9
SCS
CAN-H
7
K-LINE
No. 1 (70 A)
No. 1 (100 A)
IG11 2
08/08/21 14:54:01 61SNR030_170_0031
ProCarManuals.com
DYNOMITE -2009-


17-32EPS Components
Circuit Diagram (cont’d)
EPS CONTROL UNIT
CONNECTOR A (2P)
EPS CONTROL UNIT
CONNECTOR B (2P)
DATA LINK CONNECTOR (DLC)
GAUGE CONTROL MODULE (TACH) 36P CONNECTOR
UNDER-DASH FUSE/RELAY BOX CONNECTOR F (34P)
EPS CONTROL UNIT
CONNECTOR D (28P)
EPS CONTROL UNIT
CONNECTOR C (2P) TORQUE SENSOR
3P CONNECTOR
UNDER-DASH FUSE/RELAY BOX
CONNECTOR Q (16P)
UNDER-HOOD FUSE/RELAY BOX
CONNECTOR B (1P)
ECM/PCM CONNECTOR A (44P) EPS MOTOR 1P
CONNECTOR EPS MOTOR 2P
CONNECTOREPS MOTOR ANGLE
SENSOR 6P CONNECTOR
Wire side of female terminals
Wire side of female terminals
Terminal side of male terminals
Terminal side of female terminals
Wire side of female terminals
Wire side of female terminals
08/08/21 14:54:03 61SNR030_170_0033
ProCarManuals.com
DYNOMITE -2009-

Î
(#' '


)
µ
µ
µ
µ
DTC 11-01:
DTC 11-02:
YES
NO YES
NO
17-33
DTC Troubleshooting
EPS CONTROL UNIT CONNECTOR D (28P)
IG1 (YEL)* (GRY)*
*1: ’06 model
*2: ’07-09 models
12
Low/High IG1-terminal Voltage
(Initial Diagnosis)
Low/High IG1-terminal Voltage
(Regular Diagnosis)
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0).
4. Start the engine.
5. Wait at least 60 seconds.
Go to step 6.
Check for loose terminals or poor connections.
If the connections are good, the system is OK at
this time.
6. Turn the ignition switch to LOCK (0).
7. Disconnect EPS control unit connector D (28P). 8. Turn the ignition switch to ON (II).
9. Wait at least 60 seconds.
10. Measure the voltage between EPS control unit connector D (28P) terminal No. 16 and body ground.
Check for loose terminals in the EPS control
unit connectors, and repair if necessary. If no poor
connections are found, replace the EPS control unit
(see page 17-84).
If there is no voltage, or the voltage is lower
than specified, repair an open or high resistance in
thewirebetweentheNo.4(7.5A)fuseinthe
under-dash fuse/relay box and the EPS control unit.
If the wire checks OK, check the battery (see page
22-67), and troubleshoot the alternator regulator
circuit (see page 4-28).
Wire side of female terminalsDoes t he E PS i nd i cat or come on?
Is there battery voltage?
08/08/21 14:54:03 61SNR030_170_0034
ProCarManuals.com
DYNOMITE -2009-

µ
Î

(#' '

)
´ ´
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
DTC 12-01:
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
17-34
EPS Components
DTC Troubleshooting (cont’d)
B(WHT)
EPS CONTROL UNIT CONNECTOR A (2P) EPS CONTROL UNIT CONNECTOR A (2P)
B(WHT)
Low/High VBU Voltage (Regular
Diagnosis)
1. Turn the ignition switch to ON (II).
2. Check the BATTERY in the EPS DATA LIST with the
HDS.
Check for loose terminals or poor
connections. If the connections are good, the
system is OK at this time.
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Check the No. 1 (70 A) fuse in the under-hood fuse/ relay box.
Reinstall the checked fuse, then go to step
13.
Go to step 5.
5. Disconnect the EPS control unit connector A (2P).
6. Check for continuity between EPS control unit connector A (2P) terminal No. 2 and body ground.
Repair short to body ground in the wire
between the EPS control unit and the No. 1 (70 A)
fuse in the under-hood fuse/relay box.
Install a new No. 1 (70 A) fuse in the under-
hood fuse/relay box, then go to step 7. 7. Reconnect the EPS control unit connector A (2P).
8. Turn the ignition switch to ON (II).
9. Clear the DTC with the HDS.
10. Turn the ignition switch to LOCK (0).
11. Start the engine.
12. Check for DTCs with the HDS.
Replace the EPS control unit (see page 17-84).
Troubleshooting is complete. If any other
DTCs are indicated, go to the indicated DTC’s
troubleshooting.
13. Disconnect EPS control unit connector A (2P) and connector D (28P).
14. Measure the voltage between EPS control unit connector A (2P) terminal No. 2 and body ground.
Check for loose terminals in the EPS control
unit connectors, and repair if necessary. If no poor
connections are found, replace the EPS control unit
(see page 17-84).
Repair open in the wire between the EPS
control unit and the No. 1 (70 A) fuse in the under-
hood fuse/relay box.
Wire side of female terminals Wire side of female terminals
Is the voltage at 9.2 17.4 V ?
IsthefuseOK?
Is there continuity? Is DTC 12-01 indicated?
Is there battery voltage?
08/08/21 14:54:03 61SNR030_170_0035
ProCarManuals.com
DYNOMITE -2009-

(#'

)
Î
(#'

)
µ
µ
µ
µ
µ
µ
EPS indicator does not come on EPS indicator does not go off, and no DTCs
are stored
YES
NO
YES
NO
YES
NO
17-6017-60EPS Components
Symptom Troubleshooting
EPS CONTROL UNIT CONNECTOR D (28P)
IG1 (YEL)* (GRY)*
*1: ’06 model
*2: ’07-09 models
12
1. Turn the ignition switch to ON (II), and watch the EPS indicator.
The system is OK at this time.
Troubleshoot the gauge control module (tach)
(see page 22-241). NOTE: Check for gauge DTCs with the HDS (see page
22-3). If gauge DTCs are stored, troubleshoot those
DTCs first.
1. Turn the ignition switch to LOCK (0).
2. Check the No. 4 (7.5 A) fuse in the under-dash fuse/ relay box.
Reinstall the checked fuse, then go to step 5.
Go to step 3.
3. Disconnect EPS control unit connector D (28P).
4. Check for continuity between EPS control unit connector D (28P) terminal No. 16 and body ground.
Repair short to body ground in the wire
between the EPS control unit and the No. 4 (7.5 A)
fuse in the under-dash fuse/relay box.
Install a new No. 4 (7.5 A) fuse in the under-
dashfuse/relaybox,thengotostep5.
Wire side of female terminals
Does t he E PS i nd i cat or come on?
IsthefuseOK?
Is there continuity?
08/08/21 14:55:07 61SNR030_170_0061
ProCarManuals.com
DYNOMITE -2009-

Î
µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
17-61
EPS CONTROL UNIT CONNECTOR D (28P)
IG1 (YEL)* (GRY)*
*1: ’06 model
*2: ’07-09 models EPS CONTROL UNIT CONNECTOR A (2P)
PG (BLK)
12
5. Reconnect EPS control unit connector D (28P).
6. Turn the ignition switch to ON (II), and watch theEPS indicator.
Troubleshooting is complete.
Replace the EPS control unit (see page 17-84).
7. Disconnect EPS control unit connector D (28P).
8. Turn the ignition switch to ON (II).
9. Measure the voltage between EPS control unit connector D (28P) terminal No. 16 and body ground.
Go to step 10.
Repair open in the wire between the EPS
control unit and under-dash fuse/relay box.
10. Turn the ignition switch to LOCK (0).
11. Disconnect EPS control unit connector A (2P). 12. Check for continuity between EPS control unit
connector A (2P) terminal No. 1 and body ground.
Go to step 13.
Repair open in the wire between the EPS
control unit and body ground (G 402).
(cont’d)
Wire side of female terminals Wire side of female terminals
Does the EPS indicator come on, then go of f ?
Is there battery voltage? Is there continuity?
08/08/21 14:55:07 61SNR030_170_0062
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
18-48TPMS
Component Location Index
TIRE PRESSURE SENSOR
DATA LINK CONNECTOR (DLC) UNDER-DASH FUSE/RELAY BOX
TPMS CONTROL UNIT
TIRE PRESSURE SENSOR
TIRE PRESSURE SENSOR
TIRE PRESSURE SENSOR UNDER-HOOD FUSE/RELAY BOX
Replacement, page 18-76 Replacement, page 18-75
Replacement, page 18-76
Replacement, page 18-76
Replacement, page 18-76
08/08/21 14:58:21 61SNR030_180_0048
ProCarManuals.com
DYNOMITE -2009-


(#'

)
´
18-61
Circuit Diagram
BATTERYUNDER-HOOD
FUSE/RELAY BOX
G1
H1WHT 36
IGNITION SWITCH
No. 10
(7.5 A)
No. 2
(60 A)
No. 2
(50 A)
No. 1
(100 A)
No. 7
(7.5 A)
UNDER-DASH
FUSE/RELAY BOX
G19
D2
TPMS INDICATOR ECM/PCM WHT
RED
WHT
RED
BLK TPMS CONTROL UNIT
CAN
CONTROLLER
RED WHT RED WHT
VOLTAGE
REGULATOR8
10 IG1
B BRN
3
GND BLK
G502 G504 K-LINE
:12V
:5V
CAN H
CAN L
IG1
POWER CIRCUIT
INDICATOR
DRIVER
CIRCUIT IG1 HOT in ON (II) and START (III)
DATA LINK
CONNECTOR (DLC) LT BLUBLU
RED
BLU
2
11
LOW TIRE PRESSURE
INDICATOR
GAUGE CONTROL MODULE (TACH)
1
A36
A37 19
6
14 7
4 7Q10
Q9
MICU
(cont’d)
08/08/21 14:58:58 61SNR030_180_0061
ProCarManuals.com
DYNOMITE -2009-


18-62TPMS
Circuit Diagram (cont’d)
DATA LINK CONNECTOR (DLC)
TPMS CONTROL UNIT 20P CONNECTOR
UNDER-DASH FUSE/RELAY BOX CONNECTOR Q (16P)
ECM/PCM CONNECTOR A (44P) GAUGE CONTROL MODULE (TACH) 36P CONNECTOR
Wire side of female terminals
Terminal side of female terminals Wire side of female terminals
Wire side of female terminals
Terminal side of female terminals
08/08/21 14:58:58 61SNR030_180_0062
ProCarManuals.com
DYNOMITE -2009-


(#'

)
µ
µ µ
µ
YES
NO YES
NO
Low tire pressure indicator does not go off,
andnoDTCsarestored
18-7218-72TPMS
Symptom Troubleshooting (cont’d)
TPMS CONTROL UNIT 20P CONNECTOR
GND (BLK) IG1 (BRN)
8. Disconnect the TPMS control unit 20P connector.
9. Measure the voltage between TPMS control unit
20P connector terminals No. 3 and No. 8.
Repair short to power in the wire between
the TPMS control unit and the No. 10 (7.5 A) fuse in
the under-dash fuse/relay box.
Check for loose terminals and poor
connections at the TPMS control unit. If necessary,
substitute a known-good TPMS control unit
(see page 18-75), and recheck. 1. Turn the ignition switch to LOCK (0).
2. Disconnect the TPMS control unit 20P connector.
3. Turn the ignition switch to ON (II).
4. Check the low tire pressure indicator for several
seconds when the ignition switch is turned ON (II).
Check for loose terminals and poor
connections at the TPMS control unit. If necessary,
substitute a known-good TPMS control unit
(see page 18-75), and recheck.
Do the troubleshooting for the gauge control
module (see page 22- 241). If necessary, substitute a
known-good gauge control module (tach) (see page
22-277), and recheck.
Wire side of female terminals
Is there battery voltage? Di d t he i nd i cat or come on, and t hen go of f ?
08/08/21 14:59:00 61SNR030_180_0072
ProCarManuals.com
DYNOMITE -2009-