ignition ACURA CSX 2006 Service Repair Manual

••••••
••• •••
••• •••
••• ••• •••
••• •••
••• •••
Icon Color Information
Icon Icon Color
GREEN REDYELLOW WHITEGRAY
23-299
DisplayResult of
Connection
under the
Display
diagnosis menu
is OK. Result of
Connection
under the
Display
diagnosis menu
is NG. Executing (Not
completed)
Radio Result of
Connection
under the Radio
diagnosis menu
is OK. Result of
Connection
under the Radio
diagnosis menu
is NG. Executing (Not
completed)
XM Result of
Connection
under the XM
diagnosis menu
is OK. Result of
Connection
under the XM
diagnosis menu
is NG. Executing (Not
completed)
GPS Ant. All result of Antenna and
Receiver in NAVI
ECU is OK.Any result of
Antenna and
Receiver in NAVI
ECU is OK. Executing (Not
completed)
R-Camera Result of Connection
under the R-
Cammera
diagnosis menu
is OK. (optional)Result of
Connection
under the R-
Cammera
diagnosis menu
is NG. (optional)Result of the
Connection
under the R-
Cammera
diagnosis menu
is NG. (optional)Executing (Not
completed)
A/C Result of
Connection
under the Aircon
diagnosis menu
is OK. Result of
Connection
under the Aircon
diagnosis menu
is NG. Executing (Not
completed)
HFL Result of
Connection
under the HFL
diagnosis menu
is OK. Result of
Connection
under the HFL
diagnosis menu
is NG. Executing (Not
completed)
: DTC 2703 can be stored when the ignition switch is in ACCESSORY (I). With the ignition switch in ACCESSORY (I), the climate control unit is turned off and the navigation unit loses communication and
stores DTCs. It is possible that the system is normal with DTC 2703 stored. Check the system links with the
engine running, and if it shows normal, the system is OK at this time.
(cont’d)
08/08/21 14:16:38 61SNR030_230_0302
ProCarManuals.com
DYNOMITE -2009-

µ
Î
Î
Factory diagnostic screen In Line DiagDetailed Information & Settings
23-301
In Line Diag
123
456
789
0 Return
Navi ECU
Display XXXXCorrect PIN
GPS Antenna
RR Camera RadioXM
HFL A/C
Exit Diag
Start Diag
BACK
Delete Done
KA
Select Diagnosis Items
Self- Diagnosis Mode
Detail Information & Setting
(Navi will check internal function. connections, etc.
Perform this test with vehicle stopped and engine running.)
(Individual Diagnostic screens to confirma specific diagnostic screen.)
NOTE: If the vehicle left the factory in the factory
diagnostic mode, or if the navigation unit is replaced
you will see this screen every time you turn on the
ignition.
When a navigation unit is powered up for the first time
at the factory or after replacement with a new or
remanufactured navigation unit, the factory diagnosis
screen (In Line Diag) appears. Normally the factory
does the steps necessary to verify proper operation and
terminate the factory diagnostic.
Until the proper confirmation sequence is done, the
screen appears every time the vehicle is started.
Follow the steps below to prevent the screen from
showingupinthefuture:
 Press and hold the buttons (MENU, MAP/GUIDE, and CANCEL) for about 3 seconds. The Select Diagnosis
items screen appears.
 Press and hold the MAP/GUIDE button for 5 10 seconds. A screen with a Complete button,
appears.
 Press complete, then Return, and then shut the key off for 5 seconds. Do not disconnect the battery
during this period as the unit is saving the setting to
the SRAM memory. The In Line Diag should not
appear again.
 Restart the vehicle, and confirm normal operation by completing the TQI of the Navigation System Service
Bulletin. These section allows you to run a specific diagnostic
and allows additional setting choices for some screens
that are not shown when selecting an icon from the
System Links screen.
When you select the menu item Detail Information &
Setting menu, the main diagnosis menu is displayed.
(cont’d)
08/08/21 14:16:39 61SNR030_230_0304
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#

)(#'# 
#


)
µ
µ µ
µ
DTC 1001: DTC 1101:
YES
NO YES
NO
23-32023-320Navigation System
DTC Troubleshooting
FROM System Info Error
Media Bus Send Error
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Turn the ignition switch to LOCK (0), and then back to ON (II).
2. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355),
because there is an internal problem with the
Flash-ROM.
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-255).
Intermittent failure, the system is OK at this
time.
Is DTC 1001 indicated?
I s DT C 1101 i nd i cat ed ?
08/08/21 14:16:45 61SNR030_230_0323
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#

)µµ
µ
µ(#'# 
#
)
µ
µ µ
µ
DTC 1201: DTC 1202:
YES
NO YES
NO
23-32123-321
DVD High Temp
DVD Low Temp
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 This code sets when the internal temperature of the navigation unit ECU rises above 70 °C (158 °F). The
unit is designed to shut down to protect the
navigation unit ECU. This could be caused by an
inoperative navigation unit ECU fan or if the
passenger’s compartment temperature exceeds the
maximum. Do the troubleshooting when the unit is
within the allowable temperature range.
1. Check that the temperature is below 70 °C (158 °F) in the passenger’s compartment.
2. Clear the hard error code (see page 23-274).
3. Turn the ignition switch to LOCK (0), and then back to ON (II).
4. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time. If the unit repeatedly comes back with the
DTC, replace the navigation unit. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 This code sets when the internal temperature of the navigation unit ECU falls below 20 °C ( 4 °F). The
unit is designed to shut down to protect the
navigation unit ECU. This is usually caused by very
cold exterior temperatures. Do the troubleshooting
when the unit is within the allowable temperature
range.
1. Check that the temperature is above 20 °C ( 4 °F) in the passenger’s compartment.
2. Clear the hard error code (see page 23-274).
3. Turn the ignition switch to LOCK (0), and then back to ON (II).
4. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
I s DT C 1201 i nd i cat ed ? I s DT C 1202 i nd i cat ed ?
08/08/21 14:16:45 61SNR030_230_0324
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#

)
µ
µ µ
µ
µ
µ
DTC 1301:
YES
NO YES
NO
YES
NO
23-322Navigation System
DTC Troubleshooting (cont’d)
GPS Antenna Error
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Go to step 4.
Intermittent failure, the system is OK at this
time. 4. Turn the ignition switch to LOCK (0).
5. Check for poor connections or loose terminals at
the navigation unit connector H (2P).
6. Clear the hard error code.
7. Turn the ignition switch to LOCK (0), and then back to ON (II).
8. Check for the hard error code.
Go to step 9.
Intermittent failure, the system is OK at this
time.
9. Turn the ignition switch to LOCK (0).
10. Replace a known-good GPS antenna (see page 23-358).
11. Turn the ignition switch to ON (II).
12. Clear the hard error code.
13. Turn the ignition switch to LOCK (0), and then back to ON (II).
14. Check for the hard error code.
Replace the original GPS antenna.
Replace the navigation unit (see page 23-355).
Is DTC 1301 indicated? Is DT C 1301 ind icated ?
Is DT C 1301 ind icated ?
08/08/21 14:16:45 61SNR030_230_0325
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)
µ
µ µ
µ
µ
µ
DTC 1302:
YES
NO YES
NO
YES
NO
23-323
GPS Receiver Error 1
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside, away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Go to step 4.
Intermittent failure, the system is OK at this
time. 4. Turn the ignition switch to LOCK (0).
5. Check for poor connections or loose terminals at
the navigation unit connector H (2P).
6. Clear the hard error code (see page 23-274).
7. Turn the ignition switch to LOCK (0), and then back to ON (II).
8. Check for the hard error code (see page 23-273).
Go to step 9.
Intermittent failure, the system is OK at this
time.
9. Turn the ignition switch to LOCK (0).
10. Replace a known-good GPS antenna (see page 23-358).
11. Turn the ignition switch to ON (II).
12. Clear the hard error code (see page 23-274).
13. Turn the ignition switch to LOCK (0), and then back to ON (II).
14. Check for the hard error code (see page 23-273).
Replace the original GPS antenna.
Replace the navigation unit (see page 23-355).
Is DTC 1302 indicated? Is DTC 1302 indicated?
Is DT C 1301 ind icated ?
08/08/21 14:16:45 61SNR030_230_0326
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)µµ(#'# 
#
)
µ
µ µ
µ
DTC 1303: DTC 1305:
YES
NO YES
NO
23-32423-324Navigation System
DTC Troubleshooting (cont’d)
GPS Receiver Error 2
Gyro Error 2: ECU Temp XX °C
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside and away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Make sure the vehicle is parked outside and away from buildings.
 Aftermarket electronic devices located near the navigation unit or GPS antenna can potentially
interfere with the operation of the navigation system.
 Do this test only when the dash temperature is between 20 °C ( 4 °F) and 70 °C (158 °F).
1. Clear hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
Is DTC 1303 indicated?
Is DTC 1304 indicated?
08/08/21 14:16:46 61SNR030_230_0327
ProCarManuals.com
DYNOMITE -2009-

¦§ ¦§
(#'# 
#
)(#'# 
#
)
µ
µ
µ
µ µ
µ
µ
µ
DTC 1306: DTC 1307:
YES
NO
YES
NO YES
NO
YES
NO
23-32523-325
Vehicle Speed Pulse
DVD Read Error
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then start the engine.
3. Check for the hard error code (see page 23-273).
Go to step 4.
Intermittent failure, the system is OK at this
time.
4. Drive the vehicle and watch the VSP signal.
Replace the navigation unit (see page 23-355).
Do the symptom troubleshooting for vehicle
position icon constantly leaves road, moves
erratically or is very far from actual position
(see page 23-344). NOTE:
 Check the vehicle battery condition first.
 Check any official Honda service website for more information about the navigation system.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
 Inspect the navigation DVD for scratches or damage.
1. Turn the ignition switch to ON (II).
Go to DVD screen error messages (see page
23-319).
Go to step 2.
2. Clear the heard error code (see page 23-274).
3. Turn the ignition switch to LOCK (0), then back to ON (II).
4. Check for the hard error code (see page 23-273).
Replace the navigation unit (see page 23-355).
Intermittent failure, the system is OK at this
time.
Is DTC 1306 indicated?
Does t he V SP si gnal change f r om 0 t o 1as you drive? Is there a DVD error message?
Is DTC 1307 indicated?
08/08/21 14:16:46 61SNR030_230_0328
ProCarManuals.com
DYNOMITE -2009-

(#'# 
#
)(#'# 
#
)
µ
µ µ
µ
DTC 1402: DTC 1409:
YES
NO YES
NO
23-32623-326Navigation System
DTC Troubleshooting (cont’d)
Audio Error 2
Audio Error 9
NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Check if the audio unit functions are working
properly. If any problems are found, go to the
applicable troubleshooting in audio section.
Intermittent failure, the system is OK at this
time. NOTE:
 Check the vehicle battery condition first.
 Before you troubleshoot, make sure to follow the general troubleshooting information (see page
23-266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back to ON (II).
3. Check for the hard error code (see page 23-273).
Check the XM error codes (see page 23-194).
If any codes are detected, go to the applicable
troubleshooting in audio (XM) section.
Intermittent failure, the system is OK at this
time.
I s DT C 1402 i nd i cat ed ? I s DT C 1409 i nd i cat ed ?
08/08/21 14:16:46 61SNR030_230_0329
ProCarManuals.com
DYNOMITE -2009-

Î
(#'# 
#)
´ µ
µ
µ µ
µ
DTC 2607:
YES
NO YES
NO
23-327
NAVIGATION UNIT CONNECTOR E (14P)
GA-NET
BUS
(BLU) GA-NET
BUS
(PNK)
JUMPER WIRE
XM Diag
NOTE: Before you troubleshoot, make sure to follow the
general troubleshooting information (see page 23- 266).
1. Clear the hard error code (see page 23-274).
2. Turn the ignition switch to LOCK (0), and then back ON (II).
3. Go into the Diagnostic Menu, and select the Self- Diagnosis Mode in the Select Diagnosis Items
menu (see page 23-297).
4. Check the System Links.
Go to step 5.
Intermittent failure, the system is OK at this
time.
5. Turn the ignition switch to LOCK (0). 6. Check for poor connections or loose terminals at
navigation unit connector E (14P), USB adapter unit
connector A (14P), and XM receiver connector A
(14P).
Go to step 7.
Repair poor connections or loose terminals,
and recheck the self-diagnosis mode (see page
23-297).
7. Disconnect navigation unit connector E (14P) and XM receiver connector A (14P).
8. Connect navigation unit connector E (14P) terminals No. 9 and No. 10 with a jumper wire.
(cont’d)
Wire side of female terminals
Is the X M icon red? Ar e t he connect i ons OK ?
08/08/21 14:16:46 61SNR030_230_0330
ProCarManuals.com
DYNOMITE -2009-