change time ACURA CSX 2006 Service Repair Manual

(#')
µµ
µ
INTRODUCTION
How to Use This Manual
Safety Messages
Safety Labels
Safety Messages
Instructions
HONDA MOTOR CO., LTD.
Service Publication Office
As sections with * include SRS components;
special precautions are required when servicing.
This manual is divided into multiple sections. The first page of
each section is marked with a black tab that lines up with its
corresponding thumb index tab on this page and the back cover.
You can quickly find the first page of each section without
looking through a full table of contents. The symbols printed at
the top corner of each page can also be used as a quick
reference system.
Each section includes: 1. A table of contents, or an exploded view index showing:  Parts disassembly sequence.
 Bolt torques and thread sizes.
 Page references to descriptions in text.
2. Disassembly/assembly procedures and tools.
3. Inspection.
4. Testing/troubleshooting.
5. Repair.
6. Adjustments.
Your safety, and the safety of others, is very important. To help
you make informed decisions, we have provided safety
messages, and other safety information throughout this manual.
Of course, it is not practical or possible to warn you about all the
hazards associated with servicing this vehicle. You must use
your own good judgment.
You will find important safety information in a variety of forms
including:  on the vehicle.
 preceded by a safety alert symbol and one of three signal words, DANGER, WARNING, or CAUTION.
These signal words mean:
You WILL be KILLED or SERIOUSLY HURT if
you don’t follow instructions.
You CAN be KILLED or SERIOUSLY HURT if
you don’t follow instructions.
You CAN be HURT if you don’t follow
instructions.
 how to service this vehicle correctly and safely.
All information contained in this manual is based on the latest
product information available at the time of printing. We reserve
the right to make changes at anytime without notice. No part of
this publication may be reproduced, or stored in a retrieval
system, or transmitted, in any form by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the
prior written permission of the publisher. This includes text,
figures, and tables.
As you read this manual, you will find information that is
preceded by a symbol. The purpose of this message is
to help prevent damage to your vehicle, other property, or the
environment.
First Edition 10/2008
All Rights Reserved
Specifications apply to Canada
Specifications Maintenance
*Engine Electrical
Fuel and Emissions
*Transaxle
*Steering
*Body
*Body Electrical
*Restraints *Audio, Navigation,
and Telematics
General Information
Engine Mechanical
Engine Cooling
Brakes
(Including VSA)
*Heating, Ventilation, and Air ConditioningSuspension
(Including TPMS)
08/08/21 14:05:21 61SNR030_000_0002
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 Special Tools Required
Tighten: 3/4 Turn Clockwise
Tightening Torque: 12 N·m (1.2 kgf·m, 8.7 lbf·ft)
8-118-11
Engine Oil Filter Replacement
A
B
07HAA-PJ70101
5. Run the engine for more than 3 minutes, then checkfor oil leakage.
6. Turn the ignition switch to LOCK (0).
7. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
8. Turn the ignition switch to ON (II).
9. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain
control module (PCM). If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
10. Select GAUGES in the BODY ELECTRICAL menu with the HDS.
11. Select ADJUSTMENT in the GAUGES menu with the HDS.
12. Select SERVICE REMINDER in the ADJUSTMENT menu with the HDS.
13. Select RESET in the SERVICE REMINDER menu with the HDS.
14. Select RESETTING THE ENGINE OIL LIFE with the HDS.
NOTE: If you changed the automatic transmission
fluid (ATF) at the same time with the engine oil,
select RESETTING THE ENGINE OIL LIFE AND ATF
with the HDS instead. Oil filter wrench 07HAA-PJ70101
1. Remove the oil filter with the oil filter wrench.
2. Inspect the filter to make sure the rubber seal is not stuck to the oil filter seating surface of the engine.
3. Inspect the threads (A) and rubber seal (B) on the new filter. Clean the seat on the engine block, then
apply a light coat of new engine oil to the filter
rubber seal. Use only filters with a built-in bypass
system.
4. Install the oil filter by hand.
5. After the rubber seal seats, tighten the oil filter clockwise with the oil filter wrench.
(cont’d)
08/08/21 14:36:43 61SNR030_080_0011
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 Special Tools Required
Tighten: 3/4 Turn Clockwise
Tightening Torque: 12 N·m (1.2 kgf·m, 8.7 lbf·ft)
8-118-11
Engine Oil Filter Replacement
A
B
07HAA-PJ70101
5. Run the engine for more than 3 minutes, then checkfor oil leakage.
6. Turn the ignition switch to LOCK (0).
7. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
8. Turn the ignition switch to ON (II).
9. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain
control module (PCM). If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
10. Select GAUGES in the BODY ELECTRICAL menu with the HDS.
11. Select ADJUSTMENT in the GAUGES menu with the HDS.
12. Select SERVICE REMINDER in the ADJUSTMENT menu with the HDS.
13. Select RESET in the SERVICE REMINDER menu with the HDS.
14. Select RESETTING THE ENGINE OIL LIFE with the HDS.
NOTE: If you changed the automatic transmission
fluid (ATF) at the same time with the engine oil,
select RESETTING THE ENGINE OIL LIFE AND ATF
with the HDS instead. Oil filter wrench 07HAA-PJ70101
1. Remove the oil filter with the oil filter wrench.
2. Inspect the filter to make sure the rubber seal is not stuck to the oil filter seating surface of the engine.
3. Inspect the threads (A) and rubber seal (B) on the new filter. Clean the seat on the engine block, then
apply a light coat of new engine oil to the filter
rubber seal. Use only filters with a built-in bypass
system.
4. Install the oil filter by hand.
5. After the rubber seal seats, tighten the oil filter clockwise with the oil filter wrench.
(cont’d)
08/08/21 14:36:43 61SNR030_080_0011
ProCarManuals.com
DYNOMITE -2009-

µ
Î



Knock Sensor
Manifold Absolute Pressure (MAP) Sensor
Malfunction Indicator Lamp (MIL) Indication (In relation
to Readiness Codes) Mass Air Flow (MAF) Sensor/Intake Air Temperature
(IAT) Sensor
Output Shaft (Countershaft) Speed Sensor
A/T
11-34
Fuel and Emissions Systems
System Description (cont’d)
TERMINAL
PIEZO
CERAMIC
ELEMENT
DIAPHRAGM
O-RING TERMINAL HOT WIRE
SENSOR
O-RING
COLD WIRE
SENSOR IAT SENSOR
(THERMISTOR)
MAGNET O-RING
TERMINAL
The knock control system adjusts the ignition timing to
minimize knock.
The MAP sensor converts manifold absolute pressure
into electrical signals to the ECM/PCM.
The vehicle has certain readiness codes that are part of
the on-board diagnostics for the emissions systems. If
the vehicle’s battery has been disconnected or gone
dead, if the DTCs have been cleared, or if the ECM/PCM
has been reset, these codes are reset. In some states,
part of the emissions testing is to make sure these
codes are set to complete. If all of them are not set to
complete, the vehicle may fail the test, or the test
cannot be finished.
To check if the readiness codes are set to complete,
turn the ignition switch to ON (II), but do not start the
engine. The MIL will come on for 15 20 seconds. If it
then goes off, the readiness codes are complete. If it
flashes five times, one or more readiness codes are not
complete. To set each code, drive the vehicle or run the
engine as described in the procedures (see page 11-69). The mass air flow (MAF) sensor/intake air temperature
(IAT) sensor contains a hot wire sensor, a cold wire
sensor, and a thermistor. It is located in the intake air
passage. The resistance of the hot wire sensor, the cold
wire sensor, and the thermistor change due to intake air
temperature and air flow. The control circuit in the MAF
sensor controls the current to keep the hot wire at a set
temperature. The current is converted to voltage in the
control circuit, then output to the ECM/PCM.
This sensor detects countershaft speed.
08/08/21 14:13:38 61SNR030_110_0034
ProCarManuals.com
DYNOMITE -2009-

(#' 


)
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
DTC P0101:
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
11-74
PGM-FI System
DTC Troubleshooting
MAF Sensor Circuit Range/
Performance Problem
NOTE:
 Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
 If DTC P1128, P1129, P2228, and/or P2229 are stored at the same time as DTC P0101, troubleshoot those
DTCs first, then recheck for DTC P0101.
1. Check for poor connections or damage to these parts:
 PCV hose
 Intake air duct
 Air cleaner
 Purge (PCS) line
 Brake booster
 Brake booster hose
Go to step 2.
Repair or replace the damaged part(s), then
go to step 17.
2. Check for damage or looseness at the air duct in the air cleaner.
Go to step 3.
Reconnect or replace the air duct in the air
cleaner, then go to step 15.
3. Check for a dirty air cleaner element.
Replace the air cleaner element (see page
11-346), then go to step 15.
Go to step 4. 4. Turn the ignition switch to LOCK (0).
5. Turn the ignition switch to ON (II).
6. Check the MAF SENSOR in the DATA LIST with the
HDS.
Go to step 7.
Go to step 13.
7. Start the engine.
8. Vary the engine speed between 2,000 rpm and 3,000 rpm.
9. Check the MAF SENSOR in the DATA LIST with the HDS.
Go to step 10.
Go to step 13.
10. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in neutral) until the radiator fan
comes on, then let it idle.
11. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
 ENGINE S PEED
 VSS
 MAP SENSOR
 MAF SENSOR
12. Monitor the OBD STATUS for DTC P0101 in the DTCs MENU with the HDS.
Go to step 13.
If the screen indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals at the MAF
sensor/IAT sensor and the ECM/PCM. If the screen
indicates NOT COMPLETED, go to step 11 and
recheck.
Ar e t he par t s OK ?
Is it OK ?Is it dirty? Is t her e about 0.2 gm/ s or 0.5 V ?
Does t he r ead i ng change?
Does t he scr een i nd i cat e F AILE D?
08/08/21 14:15:37 61SNR030_110_0074
ProCarManuals.com
DYNOMITE -2009-

(#' 



)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0111:
YES
NO
YES
NO YES
NO
YES
NO
11-85
IAT Sensor Circuit Range/
Performance Problem
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Check for poor connections or loose terminals at ECT sensor 1, ECT sensor 2, and the IAT sensor.
Go to step 2.
Repair the connections or the terminals, then
go to step 15.
2. Remove the MAF sensor/IAT sensor (see page 11-224).
3. Allow the IAT sensor to cool to ambient temperature.
4. Note the ambient temperature.
5. Connect the MAF sensor/IAT sensor to its 5P connector, but do not install the sensor onto the air
cleaner.
6. Turn the ignition switch to ON (II).
7. Note the value of the IAT SENSOR quickly in the DATA LIST with the HDS.
8. Compare the value of IAT SENSOR and the ambient temperature.
Go to step 13.
Go to step 9.
9. Disconnect the MAF sensor/IAT sensor from its 5P connector.
10. Using a heat gun, blow hot air on the MAF sensor/ IAT sensor for a few seconds. Do not apply the heat
longer than a few seconds or you will damage the
sensor. 11. Connect the MAF sensor/IAT sensor to its 5P
connector, but do not install the sensor onto the air
cleaner.
12. ChecktheIATSENSORintheDATALISTwiththe HDS.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the MAF sensor/IAT sensor and the ECM/PCM.
Go to step 13.
13. Turn the ignition switch to LOCK (0).
14. Replace the MAF sensor/IAT sensor (see page 11-224).
15. Turn the ignition switch to ON (II).
16. Reset the ECM/PCM with the HDS.
17. Do the ECM/PCM idle learn procedure (see page 11-310).
18. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the MAF sensor/IAT sensor and the
ECM/PCM, then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Ar e t he connect i ons and t he t er mi nal s OK ?
Does t he v al ue of I AT SE N SOR d i f f er 3 ° C( 5.4 °F ) or mor e f r om t he ambi ent t emper at ur e? Does t he I AT SE N SOR change 33 ° C ( 5 9 ° F ) or
mor e f r om t he ambi ent t emper at ur e?
Is DTC P0111 indicated?
08/08/21 14:15:41 61SNR030_110_0085
ProCarManuals.com
DYNOMITE -2009-

(#' 


)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0116:
YES
NO
YES
NO YES
NO
YES
NO
11-90PGM-FI System
DTC Troubleshooting (cont’d)
ECT Sensor 1 Circuit Range/
Performance Problem
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Check ECT SENSOR 1 in the DATA LIST with the HDS.
Go to step 6.
Go to step 3.
3. Note the value of ECT SENSOR 1 in the DATA LIST with the HDS.
4. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
5. Check ECT SENSOR 1 in the DATA LIST with the HDS.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at ECT sensor 1 and the ECM/PCM.
Go to step 11.
6. Note the value of ECT SENSOR 1 in the DATA LIST with the HDS.
7. Turn the ignition switch to LOCK (0).
8. Open the hood, and let the engine cool for 3 hours.
9. Turn the ignition switch to ON (II). 10. Check ECT SENSOR 1 in the DATA LIST with the
HDS.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at ECT sensor 1 and the ECM/PCM.
Go to step 11.
11. Turn the ignition switch to LOCK (0).
12. Replace ECT sensor 1 (see page 11-225).
13. Turn the ignition switch to ON (II).
14. Reset the ECM/PCM with the HDS.
15. Do the ECM/PCM idle learn procedure (see page 11-310).
16. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at ECT sensor 1 and the ECM/PCM, then
go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
I s about 80 ° C ( 17 6 ° F ) or mor e, or 0.7 8 V or l ess indicated?
Does E CT SE N SOR 1 change 10 ° C ( 18 ° F ) ormor e? Does E CT SE N SOR 1 change 10 ° C ( 18 ° F ) or
mor e?
Is DTC P0116 indicated?
08/08/21 14:15:42 61SNR030_110_0090
ProCarManuals.com
DYNOMITE -2009-

µ
µ
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
11-119
12. Turn the ignition switch to LOCK (0).
13. Exchange the ignition coil from the problem
cylinder with one from another cylinder.
14. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
 ENGINE S PEED
 VSS
 REL TP SENSOR
 CLV (calculated load value)
 APP SENSOR
15. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 16.
Intermittent misfire due to poor contact at an
ignition coil connector(s). (no misfire at this time).
Check for poor connections or loose terminals at
the ignition coils.
16. Determine which cylinder had the misfire.
Replace the faulty ignition coil (see page
4-21), then go to step 60.
Go to step 17.
17. Turn the ignition switch to LOCK (0).
18. Exchange the spark plug from the problem cylinder with one from another cylinder.
19. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
 ENGINE S PEED
 VSS
 REL TP SENSOR
 CLV (calculated load value)
 APP SENSOR 20. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3
MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 21.
Intermittent misfire due to spark plug fouling
(no misfire at this time).
21. Determine which cylinder had the misfire.
Replace the faulty spark plug, then go to step
60.
Go to step 22.
22. Turn the ignition switch to LOCK (0).
23. Exchange the injector from the problem cylinder with one from the another cylinder.
24. Start the engine, and let it idle for 2 minutes.
25. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
 ENGINE S PEED
 VSS
 REL TP SENSOR
 CLV (calculated load value)
 APP SENSOR
26. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST
for 10 minutes with the HDS.
Go to step 27.
Intermittent misfire due to bad contact at an
injector connector (no misfire at this time). Check
for poor connections or loose terminals at the
injector(s).
(cont’d)
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Does the misf ir e occur in the cylinder wher e thei gni t i on coi l w as ex changed ? Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3
M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
Does the misf ir e occur in the cylinder wher e thespar k pl ug w as ex changed ?
Does the CYL1 MISFIRE, CYL2 MISFIRE, CYL3M I SF I RE , and / or CY L4 M I SF I RE show mi sf i r ecounts?
08/08/21 14:17:25 61SNR030_110_0119
ProCarManuals.com
DYNOMITE -2009-

µ
µ
µ
µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
11-299
14. Monitor the OBD STATUS for DTC P0506 in the
DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 13,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, go to step 19. If
the screen indicates EXECUTING, keep idling until
a result comes on. If the screen indicates OUT OF
CONDITION, go to step 11.
15. Remove the intake air duct from the throttle body; K20Z2 engine (see page 11-348), K20Z3 engine
(see page 11-349).
16. Check for dirt, carbon, or damage in the throttle bore.
If there is dirt or carbon, clean the throttle
body (see page 11- 344). Also check for damage to
the air cleaner element (see page 11-346), then go
to step 9. If there is damage in the throttle bore, go
to step 8.
Go to step 17.
17. Recheck with different load conditions (turn on the headlights, blower motor, rear window defogger
and/or A/C, change the gear position, etc.).
18. Monitor the OBD STATUS for DTC P0506 in the DTCs MENU with the HDS.
Intermittent failure, the system is OK at this
time.
If the screen indicates FAILED, check the A/C
system and/or the charging system, then go to step
1 and recheck. If the screen indicates EXECUTING,
keep idling until a result comes on. If the screen
indicates OUT OF CONDITION, go to step 17. 19. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
20. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle.
21. Check under these DATA LIST conditions with the HDS:
 ECTSENSOR1above70°C(156°F)
 IAT SENSOR above 0 °C (32 °F)
 VSSis0km/h(0mph)
 ST FUEL TRIM between 0.69 1.47
 FSS is CLOSED
22. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the throttle body and the ECM/PCM. If
the ECM/PCM was updated, substitute a known-
good ECM/PCM (see page 11-7), then go to step 20.
If the ECM/PCM was substituted, go to step 1.
Go to step 23.
23. Monitor the OBD STATUS for DTC P0506 in the DTCs MENU with the HDS.
If the ECM/PCM was updated,
troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM
(see page 11-228). If any other Temporary DTCs or
DTCs were indicated in step 22, go to the indicated
DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the throttle body
and the ECM/PCM. If the ECM/PCM was updated,
substitute a known-good ECM/PCM (see page 11-7),
then go to step 20. If the ECM/PCM was substituted,
go to step 1. If the screen indicates EXECUTING,
keep idling until a result comes on. If the screen
indicates OUT OF CONDITION, go to step 20.
Does t he scr een i nd i cat e PASSE D?
Is there dirt, carbon, or damage in the throttlebor e?
Does t he scr een i nd i cat e PASSE D? Is DT C P0506 ind icated ?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:28:31 61SNR030_110_0299
ProCarManuals.com
DYNOMITE -2009-

(#' 
)
µ
µ
µ
µ µ
µ
µ
µ
DTC P0507:
YES
NO
YES
NO YES
NO
YES
NO
11-300Idle Control System
DTC Troubleshooting (cont’d)
Idle Control System RPM Higher
Than Expected
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle for at least 20 seconds.
4. Monitor the OBD STATUS for DTC P0507 in the DTCs MENU with the HDS.
Go to step 5.
If the screen indicates PASSED, intermittent
failure, the system is OK at this time. If the screen
indicates EXECUTING, keep idling until a result
comes on. If the screen indicates OUT OF
CONDITION, recheck with different load conditions
(electrical, A/C, gear position, etc.), then go to
step 3.
5. Check for vacuum leaks at these parts:  PCV valve
 PCV hose
 EVAP canister purge valve
 Throttle body
 Intake manifold
 Brake booster hose
 Brake booster
Repair or replace the leaking part(s), then go
to step 6.
Go to step 6. 6. Turn the ignition switch to ON (II).
7. Reset the ECM/PCM with the HDS.
8. Do the ECM/PCM idle learn procedure (see page
11-310).
9. Start the engine. Hold the engine speed at 3,000 rpm without load (A/T in P or N, M/T in
neutral) until the radiator fan comes on, then let it
idle for at least 20 seconds.
10. Check for Temporary DTCs or DTCs with the HDS.
Go to step 12.
Go to step 11.
11. Monitor the OBD STATUS for DTC P0507 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 10,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the throttle body
and the ECM/PCM, then go to step 1. If the screen
indicates EXECUTING, keep idling until a result
comes on. If the screen indicates OUT OF
CONDITION, recheck with different load conditions
(turn on the headlights, blower motor, or A/C;
change the gear position, etc.), then go to step 9.
Does t he scr een i nd i cat e F AILE D?
Ar e t her e any l eak s? Is DT C P0507 ind icated ?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:28:31 61SNR030_110_0300
ProCarManuals.com
DYNOMITE -2009-