lock Acura MDX 2002 Manual Online

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on page
.)
Your vehicle’s air conditioning is a
sealed system. Any major mainte-
nance, such as recharging, should be
done by a qualif ied mechanic. You
can do a couple of things to make
sure the air conditioning works
ef f iciently.
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. 342
A ir Condit ioning Syst em
Maint enance284
A A
I
IRR C
COON NDDI
ITT I
IOON NIINNG G
C
CO ON NDDE
EN
NS SEER
R
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.
01/09/07 12:40:32 31S3V610_289

Open the hood.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustment of the headlights should
be perf ormed by a Acura technician
or other qualif ied mechanic.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Your vehicle has halogen headlight
bulbs, two on each side. When
replacing a bulb, handle it by its steel
base and protect the glass from
contactwithyourskinorhard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
1.
2.
CONT INUED
Replacing a Headlight Bulb
Headlight A iming
Lights
Maint enance295
C CO ON NNNEEC
CT TO
OR R
B
BU
UL LBBHalogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
01/09/07 12:42:20 31S3V610_300

Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb. Remove the socket f rom theheadlight assembly by turning it
one-quarter turn counterclockwise.
Push the electrical connector onto
the new bulb.
Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Turn on the headlights to test the
new bulb. To remove the f ront turn signal
bulb, push it in slightly and turn it
counterclockwise. To remove the
side marker bulb, pull it straight
out of its socket.
Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb into the
socket.
1.
2. 3.
4.
5.
3.
4.
5.
6. Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
Lights
Maint enance296
T T
A
A B
B
01/09/07 12:42:34 31S3V610_301

Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Your car uses halogen f og light
bulbs. See page f or inf ormation
on replacing a halogen bulb.
Remove the electrical connector
fromthebulbbysqueezingthe
connector to unlock the tab, then
slide the connector of f the bulb.
Push the electrical connector onto
the new bulb.
Use a wrench to loosen the light
assembly’s mounting bolt.
Remove the light assembly f rom
the bumper.
1.
2.
3.
4.
5.
295
CONT INUED
ReplacingaFogLightBulb
Lights
Maint enance297
C CO
ON NNNEEC
CT TO
OR R
B
BO
OL LTT
01/09/07 12:42:44 31S3V610_302

Turn on the headlights to test the
new bulb. Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
Put the light assembly into the
bumper. Tighten the mounting
bolt.Remove the socket by turning it
one-quarter turn counterclockwise.
Open the tailgate. Use a
screwdriver protected with a cloth
to pry open the two covers.
Determine which of the f our bulbs
is burned out: stop/taillight, turn
signal/hazard lights, side marker
light, or back-up light. Remove the two screws and
remove the rear light assembly
f rom the rear pillar. Remove the burned out bulb. To
remove the stop/taillight, back-up
or side marker light bulb, pull the
bulb straight out of its socket. To
remove the turn signal/hazard
light bulb, push it in and turn it
counterclockwise until it unlocks.
1.
2.
3.
4.
8. 6.
7.
5.
Replacing Rear Bulbs
Lights
Maint enance298
01/09/07 12:42:57 31S3V610_303

Put the socket back into the light
assembly and turn it clockwise to
lock it in place. Test the light to make sure the
new bulb is working. Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Install the new bulb into the
socket.
Push the socket into the light
assembly and turn it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Install the rear light assembly in
the body.Tighten the two screws.
Snap the covers back into position.
Remove the light assembly cover
by prying caref ully with a cloth-
covered screwdriver in the
notches along the top edge.Then
pivot the cover out and down.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Place the cover back into the light
assembly. Push it up until it locks
in place.
1. 4.
5.
6.
2. 3.
6.
7.
8.
9. Replacing a High-mount Brake
Light Bulb
Lights
Maint enance299
01/09/07 12:43:09 31S3V610_304

If you need to park your vehicle f or
an extended period (more than one
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors.Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the vehicle is being stored
indoors).
Fill the f uel tank.
Change the engine oil and f ilter
(see page ).
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc. are
completely dry.
Leave the parking brake off. Put
the transmission in Park. Support the f ront and rear wiper
blade arms with a f olded towel or
ragsotheydonottouchthe
windshield. Disconnect the battery.
To minimize sticking, apply a
silicone spray lubricant to all door
and tailgate seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and tailgate seals.Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Nonporous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If possible, run the engine f or a
while periodically (pref erably once
amonth).
If you store your vehicle f or 12
months or longer, have your Acura
dealer perf orm the inspections called
f or in the 24 months/30,000 miles
(48,000 km) maintenance schedule
(Normal Conditions) as soon as you
take it out of storage (see page ).
The replacements called f or in the
maintenance schedule are not
needed unless the vehicle has
actually reached that time or mileage.
263
252
St oring Your Vehicle
Maint enance303
01/09/07 12:43:47 31S3V610_308

If you have a f lat tire while driving,
stop in a saf e place to change it.
Stopping in traf f ic or on the shoulder
of a busy road is dangerous. Drive
slowly along the shoulder until you
gettoanexitoranareatostopthat
is far away from the traffic lanes.Turn on the hazard warning lights
and turn the ignition switch to
LOCK (0). Have all the
passengers get out of the vehicle
while you change the tire.
Park the vehicle on f irm, level and
non-slippery ground away f rom
traffic. Put the transmission in
Park. Apply the parking brake.
2.
1.
CONT INUED
Changing a Flat T ire
T aking Care of t he Unexpect ed315
S SP PA
A R
REE T
TI
IRRE E
J
JA
A C
CKK
T
T O
OO OLLSS
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.
01/09/07 12:45:22 31S3V610_320

Open the tailgate.Take the tools out of the storage
compartment.
Turn the jack’s end bracket
counterclockwise to loosen it, then
remove the jack.
Thetoolsandjackarebehinda
cover in the cargo area on the
driver’s side. Remove the cover by
pushing the top of the cover. The spare tire is stored
underneath the rear cargo area.
Remove the plastic cover on the
cargo area lining to access the
shaft for the spare tire hoist.
3.
4.
5.
6.7.
Changing a Flat T ire
T aking Care of t he Unexpect ed316
C CO
OV VE
ER
R C
CO
OV VE
ER
R
01/09/07 12:45:32 31S3V610_321

Loosen the f ive wheel nuts 1/2
turn with the wheel wrench.
Put the wheel nut wrench on the
hoist shaf t.Turn the wrench
counterclockwise to lower the
spare tire on the ground. Keep turning the wheel wrench to
create slack in the cable.
Remove the bracket from the
spare tire.11.
10.
8. 9.
CONT INUED
Changing a Flat T ire
T aking Care of t he Unexpect ed317
S SP
PA
A R
REE T
TI
IRRE E W
WR REEN
NC CHH B
BR
RAA C
CKKEET
T
01/09/07 12:45:42 31S3V610_322