steering wheel Acura MDX 2006 User Guide

Accelerate to the desired cruising
speedabove25mph(40km/h).
Cruise control allows you to maintain
asetspeedabove25mph(40km/h)
without keeping your f oot on the
accelerator pedal. It should be used
f or cruising on straight, open
highways. It is not recommended f or
city driving, winding roads, slippery
roads, heavy rain, or bad weather.
Press and release the SET/
DECELbuttononthesteering
wheel. The indicator on the
instrument panel comes on to
show the system is now activated. Push in the cruise control master
switch. The indicator in the switch
will come on.Cruise control may not hold the
set speed when you are going up
and down hills. If your speed
increases going down a hill, use
the brakes to slow down. This will
cancel cruise control. To resume
the set speed, press the RES/
ACCEL button. The CRUISE
CONTROL indicator on the
instrument panel comes on.
1.
2.
3.
Cruise Control
Using Cruise Control
146
CRUISE CONTROL MASTER SWITCH
CANCEL
SET/DECEL
RES/ACCEL
Improper use of cruise control
canleadtoacrash.
Use cruise control only when
traveling on open highways in
good weather.

You can cancel cruise control in any
of these ways:Tap the brake pedal.
Push the CANCEL button on the
steering wheel.
Pushthecruisecontrolmaster
button. When you push the CANCEL button
or tap the brake pedal, the system
remembers the previously set speed.
To return to that speed, accelerate to
above25mph(40km/h),andthen
press and release the RES/ACCEL
button. The CRUISE CONTROL
indicator comes on. The vehicle
accelerates to the same speed as
bef ore.
Pressing the cruise control master
switch turns the system completely
of f and erases the previous cruising
speed.
Canceling Cruise Control
Resuming the Set Speed
Cruise Control
148

µ
ÎÎ
Touring model with Navigation System Touring model without Navigation
System
To operate the HFL, use the HFL
TALK/BACKbuttonontheleftside
of the steering wheel. This inf ormation is displayed
whetherornotthephoneisbeing
used:
Phone Indicates a phone is
currently linked to the HFL.
Here is the function of each HFL
button:
HFLTalk:Thisbuttonisusedbefore
you give a command, to answer
incoming calls, and to conf irm
system inf ormation.
HFLBack:Thisbuttonisusedto
end a call, go back to the previous
voice control command, and to
cancel an operation.
HFL Buttons
HandsFreeL ink
162
Refer to your navigation system
Manual.
SIGNAL
STLENGTH
ROAM STATUS
NAVIGATION SYSTEM BUTTON HFL TALK/BCK BUTTON
PHONE
HFL TALK BUTTON
HFL BACK BUTTON
TM

Î
ε µ
Î Here are some guidelines f or using
voice control:
To enter a command, press the top
of the TALK/BACK button. Then,
af ter the beep, say your command
in a clear, natural tone.
For best system operation, set the
climate control f an speed to low,
and direct the center vents away
f rom the microphone in the ceiling.
If the HFL does not recognize a
command, its response is, ‘‘Pardon.’’
If it doesn’t recognize the
command a second time, its
response is, ‘‘Please repeat.’’ If it
doesn’t recognize the command a
third time, it plays the Help
prompt. To hear a list of available options
at any time, press the top of the
TALK/BACK button, wait f or the
beep, and say, ‘‘Hands f ree link
help.’’
Many commands can be spoken
together. For example, you can
say, ‘‘Dial 123-456-7891.’’
To enter a string of numbers in a
Call or Dial command, you can say
them all at once, or you can
separate them in blocks of 3, 4, 7,
10, and 11.
To skip a voice prompt, press the
Talk button while the HFL is
speaking. The HFL will then begin
listening f or your next command.
Signal Strength Indicates the
network signal strength.
ROAM Status (models without
navigation system) Indicates
your phone is roaming.
Some phones will not send this
inf ormation to the HFL.
TheHFLisoperatedbytheHFL
TALK/BACKbuttonontheleftside
of the steering wheel. The next f ew
pages provide easy-to-use
instructions f or all basic f eatures of
the HFL. All phones may not
operate identically, and some may
cause inconsistent operation of the
HFL. :
CONT INUED
HandsFreeL ink
Using Voice Control
How to Use the HFL
Features
163
NOTE:
TM

To go back one step in a command
process, say, ‘‘Go back,’’ or press
the Back button.
If nothing is said while the HFL is
listening f or a command, the HFL
will time out and stop its voice
recognition. The next time you
press the top of the TALK/BACK
button, the HFL begins listening
f rom the point at which it timed
out.
When you f inish a command
sequence, the HFL goes back to
its main menu. For example, when
you store the name, ‘‘Eric,’’ the
HFL response is, ‘‘Eric has been
stored.’’ The next time you pressthe Talk button, you will be at the
main menu.
To end a command sequence at
any time, press and hold the Back
button, or press the Talk button,
wait f or the beep, and say, ‘‘Cancel.’’
ThenexttimeyoupresstheTalk
button, the HFL begins f rom its
main menu. The HFL will accept a numeric, f our-
digit passcode that you can use f or
security purposes.
With the ignition in the ON (II)
position, press and release the top
of the TALK/BACK button on the
steering wheel. Af ter the beep, say
‘‘Security.’’ The HFL response is
‘‘Security options are lock, unlock,
and set passcode.’’ Press and release the top of the
TALK/BACK button. After the
beep, say the f our-digit passcode
you want to use. For example, say
‘‘1,2,3,4.’’TheHFLresponseis
‘‘1,2,3,4.Isthiscorrect?’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Yes.’’ The HFL
response is ‘‘The new passcode
has been stored. Returning to the
main menu.’’
Once a passcode is set, you can lock
the HFL so it only operates after the
passcode is entered, or you can
unlock it so anyone using your
vehicle can also use the HFL.
The HFL response is ‘‘What is the
new f our-digit passcode?’’ (If you
are changing the passcode, you
will f irst be asked f or the current
passcode.) Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Set passcode.’’
2. 1. 4.
5.
3.
To set your passcode, do this:
Setting Your Passcode L ocking or Unlocking the HFL
HandsFreeL ink
164
TM

Press this button to contact an
OnStar advisor. You will hear a
chime, f ollowed by the
announcement, ‘‘Connecting to
OnStar.’’ The connection should take
20 to 30 seconds. The advisor will
assist you with any of the services
included in your plan.
Depending on what service you
request, you may need to give your
Personal Identification Number
(PIN) to the advisor. Your PIN is a
number you make up and provide
when you establish your OnStar
service.
If cellular telephone service is not
available in the area you are driving
in, you will hear a f ast busy signal.
The system will retry the connection
several times bef ore returning to the
ready mode.A microphone is located on the
ceiling, between the f ront map lights
and the console buttons you can
speak to the advisor without taking
your hands of f the steering wheel or
diverting your attention f rom the
road. The OnStar advisor’s voice
comes f rom the audio system’s
speakers. Use the volume control on
the audio system or on the steering
wheel to adjust the volume.
You can record up to 5 minutes of
inf ormation f rom your OnStar
AdvisorortheVirtualAdvisor.This
is helpf ul f or reviewing the route,
hotel, or restaurant information you
receive f rom the OnStar center.To record a message:
During your call, the Advisor or
Virtual Advisor, press and release
the OnStar button. The system
beeps to indicate that it is
recording.
When you are f inished recording,
press and release the OnStar
button again. The system beeps
and stops recording.
To hear the first playback of a
message:
Say ‘‘Advisor playback.’’ The
recorded message is played
through the audio system
speakers. Press the CALL ANSWER/CALL
END button. The system responds
with ‘‘OnStar replay.’’
When you are f inished listening,
press the CALL ANSWER/CALL
END button. The system responds
with ‘‘Goodbye.’’
To cancel these retries, press the
white phone button.
OnStar Services Button
Recording an A dvisor or Virtual
Advisor Message
OnStar
176

Some examples are:Larger or smaller wheels and tires
can interf ere with the operation of
your vehicle’s anti-lock brakes and
other systems.
Removing parts f rom your vehicle,
or replacing components with
af termarket components could
seriously af f ect your vehicle’s
handling, stability, and reliability. Modif ying your steering wheel or
any other part of your vehicle’s
safety features can make the
systems inef f ective.
If you plan to modif y your vehicle,
consult your dealer.
Lowering your vehicle with a
non-Acura suspension kit that
signif icantly reduces ground
clearance can allow the
undercarriage to hit speed bumps
or other raised objects, which
could cause the airbags to deploy.
Raising your vehicle with a non-
Acura suspension kit can af f ect
the handling and stability.
Non-Acura wheels, because they
are a universal design, can cause
excessive stress on suspension
components and will not be
compatible with the tire Pressure
Monitoring System.
A ccessories and Modif ications
Modif ying Your Vehicle
194

Your vehicle has higher ground
clearance that allows you to travel
over bumps, obstacles, and rough
terrain. It also provides good
visibility so you can anticipate
problems earlier.
Because your vehicle rides higher
of f the ground, it has a high center
of gravity that can cause it to roll
over if you make abrupt turns. Utility
vehicles have a signif icantly higher
roll over rate than other types of
vehicles.
To prevent rollovers or loss of
control:Take corners at slower speeds
than you would with a passenger
vehicle.
Avoid sharp turns and abrupt
maneuvers whenever possible. Do not modif y your vehicle in any
way that would raise the center of
gravity.
Do not carry heavy cargo on the
roof .
Youshoulddothefollowingchecks
and adjustments bef ore you drive
your vehicle. Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove f rost, snow,
or ice. Make sure the doors and tailgate
are securely closed and locked. Check the steering wheel
adjustment (see page ). Check the adjustment of the
inside and outside mirrors (see
page ). Check the seat adjustment (see
page ). Check that any items you may be
carrying are stored properly or
f astened down securely.
When you start the engine, check
the gauges and indicators in the
instrument panel (see page ).
Visually check the tires. If a tire
looks low, use a gauge to check its
pressure. Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).
1.
2. 3.
4.
5.
6.
7.
8.
9.
95
1659
86
78
See page f or of f -highway drivingguidelines. 224
Driving Guidelines, Preparing to Drive
Driving Guidelines
Preparing to Drive
200

Check the brakes after driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious in your driving.
Your vehicle is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The anti-lock
brake system (ABS) helps you retain
steering control when braking very
hard.
The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear. Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, and reduces their ef f ectiveness.
It also keeps your brake lights on all
the time, conf using drivers behind
you. Braking System DesignBrake Wear Indicators
Braking System
210

on loose or
uneven surf aces, such as gravel or
snow, than a vehicle without anti-
lock.
If the ABS indicator and the brake
system indicator come on together
and the parking break is f ully
released, the front-to-rear braking
distribution system may also shut
down.
It only helps with steering
control during braking.
such as trying to take a
corner too f ast or making a sudden
lane change.
Always steer moderately
when you are braking hard. Severe
or sharp steering wheel movement
can still cause your vehicle to veer
into oncoming traffic or off the road. Important Saf ety Reminders A vehicle with A BS may require a longer distance to stop
A BS does not reduce the time or
distance it takes to stop the
vehicle.
A BS will not prevent a skid that
results f rom changing direction
abruptly,
A BS cannot prevent a loss of
stability.
Anti-lock Brakes (ABS)
212