buttons Acura MDX 2006 Owner's Guide

Unplug the garage door opener
motor f rom the electrical outlet.
Holdtheendof thegaragedoor
opener remote transmitter 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red indicator in
HomeLink.Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time.
Plug in the garage door opener
motor, then test the HomeLink
button by pushing it f or about 1
second. Press and hold the remote
transmitter button and one of the
HomeLink buttons at the same
time. While continuing to hold the
HomeLink button, press and
release the remote transmitter
button every 2 seconds.If the red indicator in HomeLink
continues to f lash slowly (does
not begin to f lash rapidly),
repeat steps 2 thru 4.
If the button does not work
go to step 6. If the button works,
programming is complete.
If the red indicator in HomeLink
continues to f lash slowly (does
not f lash rapidly), your remote
transmitter may stop
transmitting after a short time.
Go to step 4. If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5.
If the red indicator in HomeLink
begins to f lash slowly at f irst,
then rapidly, release both
buttons, and go to step 5.
2. 3.
1. 5. 4.
HomeL ink Universal Transceiver
Features
157

Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.
For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes.
Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure.
Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer.
PushandholdtheHomeLink
button f or a f ew seconds, then
watch the red indicator on
HomeLink.
If the indicator stays on or
flashes slowly, repeat steps 2
thru 5.
If the indicator f lashes rapidly
f or 2 seconds then stays on, you
have a rolling code transmitter:
Go to ‘‘Training with a Rolling
Code System’’ (see page ).
Repeat these steps to train the
other two HomeLink buttons to
operate any other compatible
remotely controlled devices
around your home (lighting,
automatic gate, security system,
etc.).
2. 1. 3.
6.
7.
158
HomeL ink Universal Transceiver
T raining With a Rolling Code
System
158
TRAINING BUTTON

Press and hold the button on
HomeLink f or 3 to 4 seconds.
Press and hold the HomeLink
button again f or 3 to 4 seconds.
This should turn of f the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
Press the HomeLink button again.
It should operate the garage door.Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red
indicator begins to f lash, then
release the buttons.
Youshoulderaseallthreecodes
bef ore selling the vehicle.
If you want to retrain a programmed
button f or a new device, you do not
have to erase all button memory.
You can replace the existing memory
code using this procedure:
Press and hold the HomeLink
button to be trained until the
HomeLink indicator begins to
flash slowly.If a rolling code transmitter was
previously programmed, the
indicator will f lash rapidly f or 2
seconds, and then stay on f or
about 23 seconds. If a standard transmitter was
programmed, the indicator will
stay on f or about 25 seconds.
Once the HomeLink indicator
begins to f lash slowly, continue to
hold the HomeLink button, and
f ollow steps 3thru 6under
‘‘Training HomeLink’’ (see page ).
6. 4.
5.
156
1. 2.
HomeL ink Universal Transceiver
Erasing Codes
Retraining a Button
Features
159

Your vehicle is equipped with the
HandsFreeLink (HFL). HFL uses
Bluetooth technology as a wireless
link between it and your Bluetooth
compatible cell phone. When you are
in your vehicle and your phone is
linked to the HFL, you’ll enjoy saf e,
hands-f ree phone use. The HFL is
available only in English.When the HFL is in use, the sound
comes through the vehicle’s f ront
audio system speakers. If the audio
system is in use while making a call,
the HFL over-rides the audio system.
To change the volume level, use the
audio system volume knob. The HFL can store up to 50 names
and phone numbers in its phonebook.
Withalinkedphone,youcanthen
automatically dial any name or
number in the phonebook.
Here are the main features of the
HFL. Instructions f or using the HFL
begin on page .
HFL recognizes simple voice
commands, such as phone numbers
and names. It uses these commands
to automatically dial, receive, and
store numbers. For more
inf ormation on voice control, see
UsingVoiceControlonpage .Bluetooth
is a registered trademark
of Blootooth SIG, Inc.
Bluetooth is the wireless technology
that links your phone to the HFL.
TheHFLusesaClass3Bluetooth,
which means the maximum range
between your phone and vehicle is
30 f eet (10 meters). Here are the main components of
the HFL system:
The HFL microphone is on the
ceiling, between the f ront map lights
and the console buttons. On models
with navigation system, the
microphone is shared with the
navigation system.
With a linked phone, the HFL allows
you to send and receive calls in your
vehicle without holding the phone. To use the HFL, your phone must
have approved Bluetooth capability
along with the Hands Free Prof ile.
This type of phone is available
through many phone makers and
cellular carriers. You can also find an
approved phone by visiting In Canada, visit
163
163
www.acura.com. (www.acura.ca.) or by calling the HandsFree Link customer support at (888)528-7876.
CONT INUED
BluetoothWireless Technology
Audio System Phonebook
Voice Control Microphone
Incoming/Outgoing Calls
HandsFreeL ink
Features
161
TM

µ
ÎÎ
Touring model with Navigation System Touring model without Navigation
System
To operate the HFL, use the HFL
TALK/BACKbuttonontheleftside
of the steering wheel. This inf ormation is displayed
whetherornotthephoneisbeing
used:
Phone Indicates a phone is
currently linked to the HFL.
Here is the function of each HFL
button:
HFLTalk:Thisbuttonisusedbefore
you give a command, to answer
incoming calls, and to conf irm
system inf ormation.
HFLBack:Thisbuttonisusedto
end a call, go back to the previous
voice control command, and to
cancel an operation.
HFL Buttons
HandsFreeL ink
162
Refer to your navigation system
Manual.
SIGNAL
STLENGTH
ROAM STATUS
NAVIGATION SYSTEM BUTTON HFL TALK/BCK BUTTON
PHONE
HFL TALK BUTTON
HFL BACK BUTTON
TM

The OnStarsystem in your vehicle
gives you access to a wide range of
services and information with the
touch of a button. An OnStar advisor
is available 24 hours a day, 7 days a
week.
The Saf e and Sound Plan provides
these f eatures: Roadside Assistance
Emergency Services
Automatic Notif ication of Airbag
Deployment
Accident Assist
Remote Door Locking/Unlocking
Stolen Vehicle Tracking
Misplaced Vehicle Assistance
Online Concierge Services. The Directions and Connections
Plan provides these additional
f eatures:
Route Support
Ride Assist
Inf ormation and Convenience
Services
The Luxury and Leisure Plan adds
personal concierge services.
The OnStar buttons and indicator
are located on the ceiling near the
f ront map lights.
U.S. Touring model with NavigationSystemOnStar Control Panel
OnStar
Features
175
EMERGENCY BUTTON SYSTEM
STATUS
INDICATOR
CALL ANSWER/
CALL END BUTTON
OnStar
BUTTON
VOICE
ACTIVATED
KEYPAD

Press this button to contact an
OnStar advisor. You will hear a
chime, f ollowed by the
announcement, ‘‘Connecting to
OnStar.’’ The connection should take
20 to 30 seconds. The advisor will
assist you with any of the services
included in your plan.
Depending on what service you
request, you may need to give your
Personal Identification Number
(PIN) to the advisor. Your PIN is a
number you make up and provide
when you establish your OnStar
service.
If cellular telephone service is not
available in the area you are driving
in, you will hear a f ast busy signal.
The system will retry the connection
several times bef ore returning to the
ready mode.A microphone is located on the
ceiling, between the f ront map lights
and the console buttons you can
speak to the advisor without taking
your hands of f the steering wheel or
diverting your attention f rom the
road. The OnStar advisor’s voice
comes f rom the audio system’s
speakers. Use the volume control on
the audio system or on the steering
wheel to adjust the volume.
You can record up to 5 minutes of
inf ormation f rom your OnStar
AdvisorortheVirtualAdvisor.This
is helpf ul f or reviewing the route,
hotel, or restaurant information you
receive f rom the OnStar center.To record a message:
During your call, the Advisor or
Virtual Advisor, press and release
the OnStar button. The system
beeps to indicate that it is
recording.
When you are f inished recording,
press and release the OnStar
button again. The system beeps
and stops recording.
To hear the first playback of a
message:
Say ‘‘Advisor playback.’’ The
recorded message is played
through the audio system
speakers. Press the CALL ANSWER/CALL
END button. The system responds
with ‘‘OnStar replay.’’
When you are f inished listening,
press the CALL ANSWER/CALL
END button. The system responds
with ‘‘Goodbye.’’
To cancel these retries, press the
white phone button.
OnStar Services Button
Recording an A dvisor or Virtual
Advisor Message
OnStar
176

If you cannot drive the vehicle
without f ixing the problem, and you
do not have a spare fuse, take a fuse
of the same rating or a lower rating
f rom one of the other circuits. Make
sureyoucandowithoutthatcircuit
temporarily (such as the accessory
power socket or radio).
If you replace the blown f use with a
spare f use that has a lower rating, it
might blow out again. This does not
indicate anything wrong. Replace the
f use with one of the correct rating as
soon as you can.
Look f or a burned wire inside the
f use. If it is burned out, replace it
withoneof thesparefusesof the
same rating or lower.
If the radio f use is removed, the
audio system will disable itself . The
nexttimeyouturnontheradioyou
will see ‘‘ ’’ in the f requency
display. Use the preset buttons to
enter the f ive-digit code (see page).
If the replacement fuse of the
same rating blows in a short time,
there is probably a serious
electrical problem with your
vehicle. Leave the blown fuse in
that circuit, and have your vehicle
checked by a qualif ied mechanic.
6.
5.
131
Fuses
278
BLOWN
Replacing a f use with one that has a
higher rating greatly increases the
chances of damaging the electrical
system. If you do not have a
replacement f use with the proper rating
f or the circuit, install one with a lower
rating.

...............
Gas Mileage, Improving . 192
.........................................
Gasoline .188
...............
Fuel Reserve Indicator . 63
...........................................
Gauge .68
................
Octane Requirement . 188
........................
Tank, Filling the .189
................
Gas Station Procedures . 189
Gauges ...
Engine Coolant Temperature . 69
...............................................
Fuel .68
...............................
Speedometer .68
.................................
Tachometer .68
GAWR (Gross Axle Weight .......................................
Rating) .216
GCWR (Gross Combined Weight .......................................
Rating) .216
............
Gearshif t Lever Positions . 202
......................................
Glove Box .102
GVWR (Gross Vehicle Weight .......................................
Rating) .216 .............
Halogen Headlight Bulbs . 245
.............................
HandsFreeLink .161
..............................
HFL Buttons .162
..............
Hazard Warning Flashers . 76
........................................
Headlights .74
........................................
Aiming .245
....................
Automatic Lighting .75
............
Daytime Running Lights . 76
..................
High Beam Indicator . 63
...........
High Beams, Turning on . 74
............
Low Beams, Turning on . 74
.........................
Reminder Chime .74
........
Replacing Halogen Bulbs . 245
...................................
Turning on .74
...................................
Headphones .142
..............................
Head Restraints .88
.................................
Heated Mirror .96
.................................
Heaters, Seats .91
.....................
Heating and Cooling .106
.................
High-Low Beam Switch . 74
HomeLink Universal ................................
Transceiver .156
.......................
Hood, Opening the .190
..................................................
Horn .70 ...
Identif ication Number, Vehicle . 282
Ignition ..............................................
Keys .79
...........................................
Switch .81
............
Timing Control System . 290
........................
Immobilizer System .80
.........
Important Safety Precautions . 8
.........
Indicators, Instrument Panel . 60
...............
ABS (Anti-lock Brake) . 61
....................................
A/T Temp .64
Brake (Parking and Brake ....................................
System) .61
.................................
Brake Lamp .62
........................
Charging System .60
.............................
Cruise Control .63
DRL (Daytime Running ......................................
Lights) .63
...................................
High Beam .63
........
Key (Immobilizer System) . 61
.....................................
Lights On .64
......................................
Low Fuel .63
........................
Low Oil Pressure .60
......................
Low Tire Pressure .66
...............
Maintenance Required . 67
Index
GHI
IV