mirror Acura MDX 2008 User Guide

Turn the ignition switch to the ON
(II) position.
Move the selector switch to L
(driver’s side) or R (passenger’s
side).Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown.
When you f inish, move the
selector switch to the center (off)
position. This turns the
adjustment switch of f to keep your
settings.
1.
2. 3.
4.
Mirrors
A djusting the Power Mirrors
Inst rument s and Cont rols
155
SELECTOR
SWITCH
There is also a sensor on the back of
the mirror. Items hung on the mirror
may block this sensor and af f ect its
perf ormance.
\f—\f—\fy\f
y
()-
\fy\f
\fy
2008 MDX

Both outside door mirrors have a
reverse tilt f eature. When in reverse,
the selected mirror will tilt down
slightly to improve your view as you
parallel park. Shif ting out of reverse
will return the mirrors to their
original position.To tilt the driver’s mirror, place
the selector switch in the left
position.
To tilt the passenger’s mirror,
place the switch in the right
position.
To turn the feature off, place the
switch in the center position.
Outside mirror positions can be
stored in the driving position
memory system (see page ). The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off. Pressing this button also
turns the rear window def ogger on
and off.
157
Mirrors
Reverse Tilt Door Mirror Heated Mirrors
156
HEATED MIRROR BUTTON
\f—\f—\fy\fy
()-
\fy\f

y
2008 MDX

Adjust the seat to a comfortable
position (see page ).
Store a driving position only when
the vehicle is parked.
Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Your vehicle has a memory feature
f or the steering wheel, driver’s seat,
and outside mirror positions.
Seat, except f or power lumbar,
steering wheel and outside mirror
positionscanbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Driver 1 or
Driver 2). For more inf ormation see
page .
Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current positions of the driver’s
seat, steering wheel, and outside
mirrors are now stored.
Adjust the steering wheel to a
comf ortable position (see page
).
Adjust the outside mirrors f or best
visibility (see page ). 3.
1.
2.
139
124140
155
CONT INUED
Storing a Driving Position in
Memory
Driving Position Memory System
Inst rument s and Cont rols
157
MEMO BUTTON
MEMORY BUTTONS
\f—\f—\fy\fy
()-
\fy\f
y
2008 MDX

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
Readjusting the seat position.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button. To select a memorized position, do
this:
To stop the system’s automatic
adjustment, do any of these actions:
Press any button on the control
panel: MEMO, 1, or 2.
Push any of the adjustment
switches f or the seat.
Shif t out of Park.
Adjust the outside mirrors.
Make sure the vehicle is parked.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
To change the ‘‘MEMORY
POSITION LINK’’ setting, see page . If desired, you can use the
adjustment switches to change the
positions of the seat, steering wheel
or outside mirrors af ter they are in
their memorized position. If you
change the memorized position, the
indicator in the memory button will
go out. To keep this driving position
f or later use, you must store it in the
driving position memory.
The system will move the seat,
steering wheel, and outside mirrors
to the memorized positions. The
indicator in the selected memory
button will f lash during movement.
When the adjustments are complete,
you will hear two beeps, and the
indicator will remain on.
1.
2.
98
Selecting a Memorized Position
Driving Position Memory System
158
\f—\f—\fy\fy
()-
\fy\f
y
2008 MDX

Interior Convenience Items
162
GLOVE BOXSUN VISOR VANITY MIRROR
SUNGLASSES HOLDER COAT HOOK
GROCERY HOOK
ARMREST/BEVERAGE HOLDER
CONSOLE COMPARTMENT
CENTER POCKET
BEVERAGE HOLDER
STORAGE COMPARTMENTS
ACCESSORY
POWER SOCKET ACCESSORY POWER SOCKET
\f—\f—\fy

y
()-
\fy\f
y
2008 MDX

To use the sun visor, pull it down.
Whenusingthesunvisorforthe
side window, remove the support rod
f rom the clip, and swing it out.Your vehicle has two or three
accessory power sockets, depending
on the model. All models have the
f ront accessory power socket under
the audio system and rear socket
behind the third row seat on the
driver’s side.
To use the vanity mirror on the back
of the sun visor, pull up the cover.
The vanity mirror light will not come
on if the sun visor is slid outward.
Make sure you put the sun visor
back in place when you are getting
into or out of the vehicle.
In this position, the sun visor can be
adjusted by moving it on its slider.
Do not use the extended sun visor
over the inside mirror.
Interior Convenience Items
Sun Visor Vanity Mirror A ccessory Power Sockets
166
SUN VISOR
Slide
\f—\f—\fy\f\f
y
()-
\fy\f

y
2008 MDX

Climate Control System
FRONT CONT ROL PA NELREA R CONT ROL PA NEL
170
OFF BUTTON
AUTO BUTTON
MODE BUTTON
DUAL BUTTON
REAR BUTTON
REAR PASSENGER
COMPARTMENT TEMPERATURE
AUTO BUTTON MODE BUTTON
AUTO SYNC INDICATOR
AUTO INDICATOR
FRONT PASSENGER’S SIDE TEMPERATURE
DRIVER’S SIDE TEMPERATURE
DRIVER’S SIDE
TEMPERATURE
CONTROL
BUTTONS
WINDSHIELD DEFROSTER BUTTON RECIRCULATION BUTTON
REAR PASSENGER
COMPARTMENT
TEMPERATURE
CONTROL BUTTONS OFF BUTTONFAN CONTROL BUTTONS
FAN CONTROL BUTTONS
REAR WINDOW DEFOGGER/HEATED MIRROR BUTTON
AIR CONDITIONING
BUTTON
FRONT PASSENGER’S
SIDE TEMPERATURE
CONTROL BUTTONS
\f—\f—\fy\fy
()-
\fy\f
y
2008 MDX

For your saf ety, make sure you have
a clear view through all the windows
bef ore driving.
When the indicator in the button is
on, the f ront passenger’s and rear
passenger compartment
temperatures cannot be set
separately f rom the driver’s.
Airf low is divided between
the f loor and corner vents and the
defroster vents at the base of the
windshield.
This button directs the main airflow
to the windshield for faster
def rosting. It also overrides any
mode selection you may have made.
When you select , the system
automatically switches to f resh air
mode and turns on the A/C. For
f aster def rosting, manually set the
fanspeedtohigh.Youcanalso
increase airf low to the windshield by
closing the corner vents on the
dashboard. To close the vents, rotate
the wheel under each corner vent.
When you turn of f by
pressing the button again, the
system returns to its former settings.
This button turns the rear window
def ogger of f and on (see page ).
Pushing this button also turns the
power mirror heaters on and of f .
Use the mode control button to
select the vents the air flows from.
Some air will flow from the
dashboard vents in all modes.
Air flows from the center
and corner vents in the dashboard.
Airf low is divided between
the vents in the dashboard and the
f loor vents.
Air f lows f rom the f loor
vents. 122
Climate Control System
Windshield Def rost er But t on
Rear Window Def ogger But t on
Mode Cont rol
174
\f—\f—\fy\f

y
()-
\fy\f
y
2008 MDX

Because your vehicle rides higher
of f the ground, it has a high center
of gravity that can cause it to roll
over if you make abrupt turns. Utility
vehicles have a signif icantly higher
roll over rate than other types of
vehicles.
To prevent rollovers or loss of
control:Take corners at slower speeds
than you would with a passenger
vehicle.
Avoid sharp turns and abrupt
maneuvers whenever possible. Do not modif y your vehicle in any
way that would raise the center of
gravity.
Do not carry heavy cargo on the
roof .
Your vehicle has higher ground
clearance that allows you to travel
over bumps, obstacles, and rough
terrain. It also provides good
visibility so you can anticipate
problems earlier. Youshoulddothefollowingchecks
and adjustments bef ore you drive
your vehicle.
Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove f rost, snow,
or ice.
Check that the hood is f ully closed.
Visually check the tires. If a tire
looks low, use a gauge to check its
pressure.
Check that any items you may be
carrying are stored properly or
f astened down securely.
Check the seat adjustment (see
page ).
1.
2.
3.
4.
5.
140
See page f or of f -highway driving
guidelines. 377
Driving Guidelines, Preparing to Drive
Driving Guidelines Preparing to Drive
338
——y

y
()-
yy
2008 MDX

CONT INUED
Check the adjustment of the
inside and outside mirrors (see
page ).
Check the steering wheel
adjustment (see page ).
Make sure the doors and tailgate
are securely closed and locked.
Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).
When you start the engine, check
the gauges and indicators in the
instrument panel, and the
messages on the multi-inf ormation
display (see pages , and). Without touching the accelerator
pedal, turn the ignition switch to
the START (III) position, then
release the ignition switch. You do
not need to hold the ignition
switch in the START (III) position
to start the engine. Depending on
the outside temperature, the starter motor runs f or about 6 to 9
seconds until the engine starts.
If you hold the ignition switch in
the START (III) position f or more
than 7 seconds, the starter motor,
depending on the outside
temperature, runs f or about 10 to
25 seconds until the engine starts.
If the engine does not start, wait at
least 10 seconds bef ore trying
again.
Make sure the shif t lever is in
Park. Press on the brake pedal. In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery. Apply the parking brake.
Your vehicle’s starting system has an
auto control mode. When you turn
the ignition switch to the START
(III) position, this f eature keeps the
engine’s starter motor running until
the engine starts. Follow these
instructions to start the engine:
1.
2.
3.
4.
6.
7.
8.
9.
15
124
81
10.
63 72
154
Preparing to Drive, Starting the Engine
Starting the Engine
Driving
339
T he immobilizer system protects your
vehicle f rom thef t. If an improperly-
coded key (or other device) is used, the
engine’s f uel system is disabled. For
more inf ormation, see page .
128
——y

y
()-
yy
2008 MDX