change time Acura RDX 2007 Owner's Guide

µµ
When you press the UNLOCK
button, the ceiling lights (if the front
and rear ceiling light switches are in
the door activated position) will
come on. If you do not open any door,
the lights stay on for about 30
seconds, then fade out. If you relock
the doors with the remote
transmitter before 30 seconds have
el ap sed, the lights go off
immediately.
You can change the ‘‘INTERIOR
LIGHT DIMMING TIME’’ setting in
the multi-information display (see
page ).
Press
this button once to
lock all doors and the tailgate. Some
exterior lights will flash once. When
you push LOCK twice within 5
seconds, you will hear a beep to
verify that the security system has
set. You cannot lock the doors and
thetailgateifanydoororthetailgate
is not fully closed or the key is in the
ignition switch. Press
this button once
to unlock the driver’s door. Push it
twice to unlock the remaining doors
and the tailgate. Some exterior lights
will flash twice each time you press
the button.
You can change the ‘‘KEYLESS
LOCK ACKNOWLEDGMENT’’
setting in the multi-information
display (see page ).
You can change the ‘‘DOOR LOCK
MODE’’ setting in the multi-
info rmation display (see page ).
103
110
112
On RDX with Technology Package
model
On RDX with Technology Packagemodel
Remote Transmitter
LOCK UNL OCK
140
UNLOCK
BUTTON
LOCK
BUTTON
PANIC
BUTTON
——
y

y
() y
y

µ
If
you unlock the doors and the
tailgate with the remote transmitter,
but do not open any of the doors or
thetailgatewithin30seconds,the
doors and the tailgate automatically
relock and the security system sets. Protect
the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
Avoid
dropping or thro wing the
transmitter.
You can change the ‘‘SECURITY
RELOCK TIMER’’ setting in the
multi-inf ormation display (see page ).
Pressthisbuttonfor
about 1 second to attract attention;
the horn will sound, and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
button on the remote transmitter, or
turn the ignition switch to the ON
(II) position. 114
On RDX with Technology Package
model
Remote Transmitter
Remote Transmitter Care
PA NIC
Inst rument s and Cont rols
141
——
y

y
() y
y

Open any door.
Remove the key from the ignition
switch.
Unlock the doors with the key,
locktabonthedriver’sdoor,
master door lock switch, or
remote transmitter.
After all doors are closed tightly, the
light(s) dims slightly, then fades out
in about 30 seconds. If
you do not open any door after
unlocking the driver’s door or
removing the key from the ignition
switch, the light(s) fade out in about
30 seconds. If you leave any door
open without the key in the ignition
switch, the light(s) will go off after 3
minutes.
You can use the front ceiling lights
whenever the lights are off.
To turn the lights on or off, push its
lens.
In
the door activated position, both
front and rear ceiling lights come on
when you:
You can change the ‘‘INTERIOR
LIGHT DIMMING TIME’’ setting in
the multi-information display (see
page ).103
On RDX with Technology Package
model
Interior Lights
Inst rument s and Cont rols
159
LENSES
——
y

y
() y
y

The courtesy lights in the ceiling
console come on when the light
switch is in the or the
position. You can adjust their
brightness by turning the Select/
Reset knob on the instrument panel. The
cargo area light has a two
position switch. In the OFF (right)
position, the light does not come on.
In the ON (left) position, the light
comesonwhenyou openthetailgate.
Your
vehicle also has a courtesy light
in the ignition switch. This light
comesonwhenyou;
Unlock the driver’s door.
Remove the key from the ignition
switch. Open any door.
The
courtesy light in each front door
comes on when the door is opened,
and goes out when the door is closed.
After all doors are closed tightly, the
light fades out in about 30 seconds.
You can change the ‘‘INTERIOR
LIGHT DIMMING TIME’’ setting in
the multi-information display (see
page ). 103
On RDX with Technology Package
model
Interior Lights
Courtesy Lights Cargo Area Light
160
COURTESY LIGHTS ON OFF
——
y

y
() y
y

If you press the OFF button, the
climate control system shuts of f
completely.
Air flows from the center
and corner vents in the dashboard.
Airf low is divided between
the vents in the dashboard and the
f loor vents.
Air f lows f rom the f loor
vents.
Airf low is divided between
the f loor vents and the def roster
vents at the base of the windshield. To keep stale air and mustiness
f rom collecting, you should have
the f an running at all times. Keep the system of f f or short
periods only.
The mode indicator in the display
changes to the current mode each
time you press the button.
When the climate control system is
turned off, the temperature in the
display will also turn of f .
Use the MODE button to select the
vents the air flows from. Some air
will f low f rom the dashboard corner
vents in all modes.
To Turn Everything Off
Mode Button
Climate Control System
174
——
y

y
() y
y

To load a single disc:Press and release the LOAD
button on the changer unit. You
will see ‘‘BUSY’’ on the center
display, and the disc load indicator
turns red and starts blinking.
Insert a disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display at the same time.
Insert the disc only about half way;
the drive will pull it in the rest of
the way. You will see the disc
indicator blinking on the center
display.
To load multiple discs in one
operation:
When the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display again, insert the
next CD in the slot.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
Repeat steps 1 through 3 until all
six positions are loaded. If you are
not loading all six positions, press
the LOAD button again after the
last CD has loaded. ‘‘DISC READ’’
appears on the center display, then
the system begins playing the last
CD loaded.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 10 seconds, stop the load
operation, and begin playing the last
disc loaded.
Press and hold the LOAD button
on the changer unit until you hear
a beep. You will see ‘‘BUSY’’ on
the center display, and disc load
indicator turns red and starts
blinking.
Insert the disc into the disc slot
when the disc load indicator turns
green and ‘‘LOAD’’ appears on the
center display at the same time.
Insert it only half way; the drive
will pull it in the rest of the way.
You will see ‘‘BUSY’’ on the center
display, and the disc load indicator
turns red again and blinks as the
CD is loaded.
Do not try to insert a disc until
‘‘LOAD’’ appears. You could
damage the audio unit.
1.
2.
3.
1.
2. 4.
Audio System
L oading CDs in the Changer
186
——
y
y
() y

y

Each time you press the DISP/
MODE (U.S. model) or DISP
(Canadian model) button while
playing a CD (CD-DA), the center
display changes f rom album name,
to track name, to artist name, and
then to normal display. If the disc
was not recorded with CD-TEXT,
‘‘NO INFO’’ will be shown on the
center display.If the title is too long, it will not show
all at once. Press and hold the DISP/
MODE (U.S. model) or DISP
(Canadian model) button, and the
rest of the title will show on the
center display.
When playing a disc compressed in
MP3/WMA format, the display
changes f rom f older name, to f ile
name, to artist tag, to album tag, to
track tag, and then to normal display
each time you press the DISP/
MODE (U.S. model) or DISP
(Canadian model) button. If the disc
was not recorded with this
inf ormation, ‘‘NO INFO’’ will be
shownonthecenterdisplay. You will also see the album and track
name (CD-TEXT), or the f older and
f ile name (MP3/WMA) under these
conditions:
Each time a new track, file, or
folder plays. When you insert a disc, and the
system begins to play.
The specif ications of the compatible
MP3 f ile are:
Sampling f requency: 32/44.1/48 kHz
(MPEG1), 24, 22.05, 16 kHz
(MPEG2)
Bit rate: 32/40/48/56/64/80/96/
112/128/160/192/224/256/320 kbps
(MPEG1), 8/16/24/32/40/48/56/
64/80/96/112/128/160 kbps
(MPEG2)
Compatible with variable bit rate and
multi-session.
Maximum layers
(including ROOT): 8 layers
The specif ications of the compatible
WMA f ile are:
Sampling f requency: 32/44.1/48 kHz
Bit rate: 48/64/80/96/128/160/192
kbps
Compatible with variable bit rate and
multi-session.
Maximum layers (including ROOT):
8 layers
Name Display Funct ion
Audio System
188
——
y
y
() y
y

µµ
µ
While a disc is playing you can use
the SEEK/SKIP bar to select
passages and change tracks (f iles in
MP3/WMA mode).
In MP3/WMA mode, use the
TUNE/FOLDER bar to select
f olders in the disc, and use the
SEEK/SKIP bar to change f iles.
Each time you
press and release the side of
the SEEK/SKIP bar, the system
skips forward to the beginning of the
next track (f ile in MP3/WMA mode).
Press and release the side of
the bar to skip backward to the
beginning of the current track/f ile.
Press it again to skip to the
beginning of the previous track/f ile. To
select a dif f erent f older, press and
releasethe sideof theTUNE/
FOLDERbartomovetothe
beginning of the next f older. Press
and release the side of the bar
to move to the beginning of the
current f older. Press it again to skip
to the beginning of the previous
f older.
This f eature, when
activated, continuously replays the
current track (f ile in MP3/WMA
mode). To activate it, press and
release the RPT button. You will see
‘‘RPT’’ on the center display. To turn
of f this f eature, press the RPT
button for more than 2 seconds.
To move rapidly within a track/f ile,
press and hold the or side
of the SEEK/SKIP bar.In MP3/WMA mode
CONT INUED
T o Change or Select T racks/FilesSEEK /SK IP
FOLDER SELECTION
REPEAT
Audio System
Features
189
——
y

y
() y
y

µ
µ µ
µ
In MP3/WMA mode In MP3/WMA mode
This feature,
when activated, replays all the f iles
on the current f older in the order
they are compressed in MP3/WMA.
To activate f older repeat mode, press
the RPT button twice. You will see
‘‘F-RPT’’ on the center display. Press
andholdtheRPTbuttonformore
than 2 seconds to turn off this
feature.
Press the RPT
button twice to continuously replay
the current CD. In MP3/WMA mode,
press the RPT button three times.
You will see ‘‘D-RPT’’ on the center
display. Press and hold the RPT
button for more than 2 seconds to
turn off this feature. The scan f unction samples
all the tracks (f iles in a f older in
MP3/WMA mode) of the current
disc in the order they are recorded
on the CD. To activate this feature,
press and release the SCAN button.
You will see ‘‘SCAN’’ and the track/
f ile number f lashing on the center
display. The system will then play
the track/f ile f or approximately 10
seconds. To hear the rest of the
track/file, press and hold the SCAN
button for more than 2 seconds. If
you do nothing, the system will then
play the f ollowing tracks/f iles f or 10
seconds each. When the system
f inishes scanning all the tracks/f iles
in the current disc, the system
returns to the track/f ile it f irst
started scanning with, scan is
canceled and the system begins to
play that track/file normally. The folder scan
f unction samples the f irst f ile of each
f older of the current disc in the
order they are compressed in MP3/
WMA. To activate this feature, press
the SCAN button twice. The first file
of each f older plays f or about 10
seconds. You will see ‘‘F-SCAN’’ and
the f older number f lashing on the
center display. To hear the rest of
the f ile in the f older currently
scanning, press and hold the SCAN
button for more than 2 seconds.
When the system f inishes scanning
all the f olders of the current disc, the
system returns to the f older it
started scanning with, f older scan is
canceled and the system begins to
play that folder normally.
Each time you press and release the
RPT button, the mode changes from
repeat to f older repeat, disc repeat
then to normal playing. FOLDER REPEAT
DISC REPEAT SCAN
FOLDER SCAN
Audio System
190
——
y
y
() y
y

µµ
µ
The disc scan
f unction samples the f irst track (f ile
in MP3/WMA mode) of each disc
within the changer in numerical
order. To activate this f eature, press
the SCAN button twice. In MP3/
WMA mode, press the SCAN button
three times. The f irst track/f ile of
each disc plays f or about 10 seconds.
You will see ‘‘D-SCAN’’ and disc
number f lashing on the center
display. To hear the rest of the
track/f ile in the disc currently
scanning, press and hold the SCAN
button for more than 2 seconds.
When the system f inishes scanning
all the discs, disc scan is canceled
and the system begins to play the
first track/file of that disc normally. This
f eature plays the f iles within a f older
in random order, rather than in the
order they are compressed in MP3/
WMA. To activate it, press the
A. SEL/RDM button once. You will
see ‘‘F-RDM’’ on the center display.
The system will then select and play
f iles randomly. This continues until
you deactivate folder random play by
pressing and holding the RDM
button for more than 2 seconds.
Each time you press and release the
SCAN button, the mode changes
f rom scan to f older scan, disc scan
then to normal playing.
This f eature plays the
tracks (all f iles in each f older in
MP3/WMA mode) within a disc in
random order. To activate it, press
and release the A. SEL/RDM button.
In MP3/WMA mode, press the
A. SEL/RDM button twice to select
within a disc random play. You will
see ‘‘RDM’’ on the center display.
Press and hold the A. SEL/RDM
button for more than 2 seconds to
return to normal play. Each time you press and release the
A. SEL/RDM button, the mode
changes f rom f older random to
random, then to normal playing.In MP3/WMA modeDISC SCAN
FOLDER RANDOM
RANDOM (Random within a
Disc)
Audio System
Features
191
——
y
y
() y
y