tailgate Acura RDX 2007 Owner's Guide

The courtesy lights in the ceiling
console come on when the light
switch is in the or the
position. You can adjust their
brightness by turning the Select/
Reset knob on the instrument panel. The
cargo area light has a two
position switch. In the OFF (right)
position, the light does not come on.
In the ON (left) position, the light
comesonwhenyou openthetailgate.
Your
vehicle also has a courtesy light
in the ignition switch. This light
comesonwhenyou;
Unlock the driver’s door.
Remove the key from the ignition
switch. Open any door.
The
courtesy light in each front door
comes on when the door is opened,
and goes out when the door is closed.
After all doors are closed tightly, the
light fades out in about 30 seconds.
You can change the ‘‘INTERIOR
LIGHT DIMMING TIME’’ setting in
the multi-information display (see
page ). 103
On RDX with Technology Package
model
Interior Lights
Courtesy Lights Cargo Area Light
160
COURTESY LIGHTS ON OFF
——
y

y
() y
y

Your vehicle has a cargo area cover
to conceal your luggage and protect
them f rom direct sunlight.To remove it:
Place the cargo area cover on the
cargo area f loor.
Make sure the cargo area cover is
securely placed so it will not move
while you are driving.
Do not put any items on top of the
cargo area cover. They can block
your view and be thrown around the
vehicle during a crash.
The cargo area cover may be
removed to give you more cargo
space. Lif t and pull the rear edge of the
cargo area cover slightly to unlock
it from the hanger bars, then
remove it straight out.
Reverse this procedure to install the
cargo area cover.
Open the tailgate. Remove the
hook f rom the tab on the tailgate.
Make sure you use both hands to
prevent the cargo area cover f rom
f alling accidentally.
1.
2. 3.
Interior Convenience Items
Cargo Area Cover
Inst rument s and Cont rols
167
CARGO
AREA
COVER
HANGER BAR
HOOK TAB
——
y
y
() y
y

The security system automatically
sets 15 seconds after you lock the
doors, hood, and the tailgate. For the
system to activate, you must lock the
doorsandthetailgatefromthe
outside with the key, driver’s lock
tab, door lock master switch, or
remote transmitter. The security
system indicator on the instrument
panel starts blinking immediately to
show you the system is setting itself . The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking lights, side
marker lights, and taillights f lashes if
someone attempts to break into your
vehicleorremovetheradio.This
alarm continues f or 2 minutes, then
the system resets. To reset an
alarming system before the 2
minutes have elapsed, unlock the
driver’s door with the key or the
remote transmitter.Once the security system is set,
opening any door, the tailgate, or the
hood without using the key or the
remote transmitter, will cause it to
alarm. It also alarms if the radio is
removed f rom the dashboard or the
wiring is cut.Do not attempt to alter this system
or add other devices to it.To see if the system is set
af ter you exit the vehicle, press the
LOCK button on the remote
transmitter within 5 seconds. If the
system is set, a beep will sound. The security system will not set if
the hood, tailgate, or any door is not
f ully closed. Bef ore you leave the
vehicle, make sure the doors,
tailgate, and hood are securely
closed. The alarm will also be activated if
the passenger inside the locked
vehicle turns the ignition switch on.
Security System
240
NOTE:SECURITY SYSTEM INDICATOR
——
y
y
() yy

Store or secure all items that could
be thro wn around and hurt
someone during a crash.
Keep the glove box closed while
driving. If it is open, a passenger
could injure their knees during a
crash or sudden stop.
Be
sure items placed on the floor
behind the front seats cannot roll
under the seats and interfere with
the driver’s ability to operate the
pedals, the proper operation of the
seats, or proper operation of the
sensors under the seats.
Do not put any items on top of the
cargo area cover. They can block
your view and be thrown around
the vehicle during a crash. Distribute
cargo evenly on the
floor of the cargo area, placing the
heaviest items on the bottom and
as far forward as possible. Tie
down items that could be thro wn
about the vehicle during a crash or
sudden stop.
Ifyoufoldtherearseatsdown,tie
down items that could be thro wn
about the vehicle during a crash or
sudden stop. Also, keep all cargo
below the bottom of the windows.
If it is higher, it could interfere
with the proper operation of the
side curtain airbags. If you carry large items that
prevent you f rom closing the
tailgate, exhaust gas can enter the
passenger area. To avoid the
possibility of
, f ollow the instructions
on page .
If you carry any items on a roof
rack,besurethetotalweightof
the rack and the items does not
exceed the maximum allowable
weight. Please contact your dealer
for further information.
If you use an accessory roof rack,
the roof rack weight limit may be
lower. Ref er to the inf ormation that
came with your roof rack. 58
Carrying Cargo in the Passenger
Compartment
Carrying Cargo in the Cargo A rea
carbon monoxide
poisoning
Carrying Cargo
Bef ore Driving
289
——
y
y
() yy

Check the seat adjustment (see
page ).
Check the adjustment of the
inside and outside mirrors (see
page ).
Check the steering wheel
ad justment (see page ).
Fasten your seat belt. Check that
your passengers have fastened
their seat belts (see page ).
Make
sure the doors and the
tailgate are secu rely closed and
locked. When
you start the engine, check
the gauges and indicato rs in the
instrument panel, and the
messages in the info rmation
display or multi -information
display (depending on models)
(see pages,,, and
).
Youshoulddothesechecksand
adjustments
before you drive your
vehicle:
Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove frost, snow,
or ice.
Check that the hood is fully closed.
Vi sually check the tires. If a tire
looks low, use a gauge to check its
pressure (see page ).
Check that any items you may be
carrying are stored properly or
f astened down securely.
1.
2.
3.
4. 5.
6.
7.
8.
9.
10.
16
155
126
372 145
63
84 64 75
Preparing to Drive
Driving
293
——
y


y
() yy

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly, or
your vehicle may roll if it is parked
on an incline.Make sure the moonroof and the
windows are closed.
If the vehicle is f acing uphill, turn
the front wheels away from the
curb.
If the vehicle is f acing downhill,
turn the front wheels toward the
curb.
Check the indicator on the
instrument panel to verif y that the
security system is set.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
Set the parking brake bef ore you put
the transmission in Park. This keeps
the vehicle from moving and putting
pressure on the parking mechanism
in the transmission.
Turn of f the lights.
Place any packages, valuables, etc.
in the cargo area or take them
with you.
Lock the doors and the tailgate.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire.
Parking T ips
Parking
Driving
305
——
y
y
() y
y

Each wheel is equipped with a tire
pressure sensor mounted inside the
tire behind the valve stem. You must
use TPMS specific wheels. It is
recommended that you always have
your tires serviced by your dealer or
qualified technician.
Your vehicle has a tire pressure
monitor on the info rmation display. The
tire pressure monitor uses the
same display as the door and tailgate
open monitor. When any of the tires
has low pressure, the low tire
pressure indicator on the instrument
panel comes on, and you will also see
which tire is losing the pressu re on
the tire pressure monitor.
If the TPMS indicator comes on, the
tire pressure monitor does not work
(see page ).
If the low tire pressure indicator and
the low tire position on the low tire
pressure monitor do not go out af ter
inf lating the tires to the specif ied
values, have your dealer check the
system as soon as possible. 73
CONT INUED
On RDX model
Tire Pressure Monitoring System (TPMS)
Tire Pressure Monitor
Driving
311
LOW PRESSURE TIRE
——
y

y
() y
y

Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.
Determine which of the two bulbs
is burned out: taillight or back-up
light.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Turn on the lights to make sure
the new bulb is working.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Reinstall the light assembly cover.
1.
2. 3.
4.5.
6.
7.
Lights
Replacing Rear Bulbs
(in Tailgate)
Maint enance
361
COVER
NOTCH SOCKETS
BULBS
——
y

y
() yy

Remove the two bolt covers on the
rear pillar by prying on the bottom
edge with a flat-tip screwdriver.
Remove the bolts with a Phillips-
head screwdriver, and remove the
light assembly f rom the rear pillar.Determine which of the three
bulbs is burned out: brake/
taillight, turn signal or rear side
marker.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Turn on the lights to make sure
the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Install the rear light assembly in
the rear pillar. Tighten the two
bolts. Snap the bolt covers into
position.
Open the tailgate.
2.
4.
5.6.
7.
8.
3.
1.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
362
COVERS BOLTS
BULBSOCKET
——
y
y
() yy

Install the new bulb into the hole
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Put the undercover in place.
Reinstall the clip, and tighten the
screw securely.Remove the two screw covers on
the light assembly by prying on
the side edge with a flat-tip
screwdriver.
Remove the screws with a Phillips-
head screwdriver, then remove
the light assembly f rom the
tailgate.Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
5.
6.
7.
8.
1.
2.3.
4.
Lights
Replacing a High-mount Brake
Light Bulb
364
COVERS SOCKET
BULB
SCREWS
——
y

y
() yy